High performance engineering materials, poly(arylene ether)s, having very good mechanical properties, excellent oxidative and hydrolytic stability are promising candidates for alternative materials used in the field of Proton Exchange Membrane Fuel Cells (PEMFCs) and Reverse Osmosis (RO) applications. In particular, wholly aromatic sulfonated poly(arylene ether sulfone)s are of considerable interest in the field of PEMFCs and RO, due to their affordability, high Tg, and the ease of sulfonation. Proton exchange membrane fuels cells (PEMFCs) are one of the primary alternate source of energy. A Proton exchange membrane (PEM) is one of the key component in a PEMFC and it needs to have good proton conductivity under partially humidified conditions. One of the strategies to increase proton conductivity under partially RH conditions is to synthesize hydrophobic-hydrophilic multiblock copolymers with high Ion exchange capacity (IEC) values to ensure sufficient ion channel size. In this thesis two multiblock systems were synthesized incorporating trisulfonated hydrophilic oligomers and were characterized in the first two chapters of the thesis. The first multiblock system incorporated a non-fluorinated biphenol-based hydrophobic block. The second study was focused on synthesizing a fluorinated benzonitrile-based hydrophobic block. A fluorinated monomer was incorporated with the aim to improve phase separation which might lead to increased performance under partially humidified conditions. The third study featured synthesis and characterization of a novel hydroquinone-based random copolymer system precursor, which after post-sulfonation, shall form mono-sulfonated polysulfone materials with potential applications in reverse osmosis. The ratio of the amount of hydroquinone incorporated in the copolymer were varied during the synthesis of the precursor to facilitate control over the post-sulfonation process. The simple and low cost process of post-sulfonating the random copolymer enables the precursor to be a promising material to be used in the reverse osmosis application. / Master of Science

The polyamide poly(ε-caprolactam) or "nylon 6" is a very important fiber forming polymer which finds many applications in the carpet industry and elsewhere due to the very high strength of this fiber. However, a major drawback is its hydrophilicity. This feature influences both the surface and bulk mechanical behavior. Siloxane based macromolecules are hydrophobic, thermally stable and exhibit dimensional stability over a wide temperature range. Unlike the polyamide nylon 6, these hydrophobic materials display relatively low surface free energy. Thus, they can be used for the surface modification of nylon 6, provided a suitable adhesion or "anchoring" method is feasible. Polyamide-polydimethylsiloxane segmented or block copolymers were found to be suitable "interfacial" agents. They were synthesized by reacting aminopropyl-terminated polydimethylsiloxane (PDMS) oligomers with sebacyl chloride via an interfacial polymerization in which methylene chloride was used as the solvent or organic phase. A second diamine "chain extender" was also utilized, if desired. By varying the mole ratio of soft segment to the chain extender p-aminocyclohexylmethane (PACM-20), copolymers with various percentages of hard segments can be synthesized. Weight fractions of 2, 5, or 10% of the polyamide-poly-dimethylsiloxane block copolymers were physically melt mixed with nylon 6 in an extruder. The presence of polydimethylsiloxane on the surface of the blend was detected by determining the critical surface tensions of wetting using water as the contact angle test liquid. Such modified polyamides were successfully melt spun into fibers which displayed good mechanical properties and enhanced soil resistance. Fibers spun from these modified nylon 6 blends showed surface hydrophobicity. These modified polyamides or related materials may become technologically important in carpeting applications. Additional studies involving attempts at directly polymerizing ε-caprolactam via hydrolytic ring opening polymerization from functional polysiloxanes are also reported. In general, the structural integrity of these copolymers is less well defined. Certain procedures utilizing the aminopropyl polydimethylsiloxane initiated lactam oligomerization, followed by adipic acid chain extension produced interesting materials and should be further examined. / Master of Science / incomplete_metadata

The time dependence of the physical properties of ethylene/1-octene (EO)-copolymers after primary crystallization is investigated by calorimetry, density, and creep measurements. The temporal evolution of the multiple melting of EO-copolymers is monitored by differential scanning calorimetry. The low temperature endotherm displays an evolution similar to that observed for the enthalpy recovery in glasses after physical aging. Using this analogy, a calorimetry-aging rate is defined, which quantifies the change in the low endotherm temperature with time. Similarly a density-aging rate is defined from the evolution of density with time. A non-classical creep behavior is observed for short aging times, consistent with crystallization-induced shrinkage. The change in crystallinity during aging leads to a change in the shape of the relaxation spectrum. Hence, analysis of creep data cannot be carried out using Struik's superposition method. For both short and long aging times, the creep rate exhibits a dependence on copolymer composition similar to those associated with the calorimetry- and the density-aging rates, suggesting a common origin for the evolution of the low endotherm, the creep behavior and the bulk density. The calorimetry, density, and creep data are reexamined based on the following assumptions: First, a single population of small crystals is formed during crystallization at low temperature; Second, these small crystals increase in stability under isothermal conditions, easily melt and recrystallize during heating and serve as efficient thermo-reversible cross-links to increase the conformational constraints in the residual amorphous fraction. These assumptions appear to be consistent with all observations made to date. / Master of Science

For the first time, triblock copolymers of novel styrenic-based macromolecules were investigated in detail and examined for structure-morphology-performance relationships. We were able to design novel imidazolium- and phosphonium-containing styrenic macromolecules using controlled radical polymerization and conventional free radical polymerization strategies, for a variety of potential applications including electromechanical devices, ionic liquids, adhesives, and lithium-ion batteries. Block copolymers have a unique architecture providing physical crosslinking to behave as thermoplastic elastomers. We preferred ABA triblock copolymers as compared to random and diblock copolymers for improved mechanical performance. ABA triblock copolymers synthesized using nitroxide-mediated polymerization (NMP) of polystyrene external blocks and a charged imidazolium-containing central block, exhibited sufficient modulus and ionic conductivity for electromechanical transducers. We successfully reported the actuation behavior of triblock copolymers in the presence of added ionic liquid for the first time. We proposed that diluting the ion concentration of the ion-rich phase with neutral polymer comonomers that reduces Tg, increases ion dissociation, and potentially maximizes ionic conductivity. Tendency of ethylene-oxide units to coordinate cations, forming stable crown ether-like, multi-nuclear coordination complexes, promotes solvation and dissociation of ionic aggregates. In situ Fourier transform infrared spectroscopy (FTIR) was used to monitor the thermal polymerization in various acrylate and methacrylate monomers. It was found that acrylates have lower activation energy than methacrylates. The copolymerizations of poly(ethylene glycol)methyl ether acrylate (EG9MEA) and imidazole-containing monomer (VBIm) resulted in controlled polymerization kinetics with narrow molecular weight distributions. The control behavior of the copolymerizations is likely attributed to the observed decrease in calculated apparent rate constants for the copolymerizations with addition of VBIm as comonomer. Reversible addition fragmentation transfer (RAFT) successfully synthesized well-defined A-BC-A triblock copolymers containing a synergy of pendant ether and imidazolium sites. We demonstrated that electromechanical transducers derived from these triblock copolymer membranes with added ionic liquid showed superior actuation performance compared to a benchmark Nafion® membrane, suggesting potential for ionic polymer device applications. This was attributed to optimum modulus, improved ionic conductivity, and microphase-separated morphology of triblock copolymers. Conventional free radical polymerization and anion metathesis of 4-(diphenylphosphino)styrene (DPPS) successfully generated high molecular weight triaryl phosphine-containing copolymers. These macromolecules have no -CH2 group at the benzylic position increasing the thermal stability of the DPPS-containing polymers. Counterion exchange to fluorinated, bulkier anions broadened the library of polyelectrolytes, led to improved thermal stabilities, lower glass transition temperatures, and tunable wetting behavior. We also reported the synthesis of salt-responsive copolymers using conventional free radical polymerization. Adhesive performance measurements such as peel tests and probe tack enforced the application of these polymers as pressure sensitive adhesives. We also demonstrated the synthesis and subsequent neutralization of novel, well-defined A-BC-A triblock copolymers containing a soft central 'BC' block consisting of Sty-Tf2N and DEGMEMA with polystyrene external blocks. Sty-Tf2N monomer enables an important delocalization of the negative charge. Li+ has weak interactions with this anionic structure, consequently enabling a high dissociation level. Li+ ions are associated to the polymer chain to produce high transport numbers. Furthermore, incorporating DEGMEMA lowers the Tg of the charged block copolymers, thereby increasing the segmental mobility and thus ionic conductivity. Finally, the structure-property-morphology study of these triblock copolymers will be helpful for their use in potential applications such as ion-containing membranes, lithium-ion batteries. / Ph. D.

Three block copolymer systems where one block was that of an engineering thermoplastic were examined. The first was that of polysulfone-polyarylester block copolymers where glassy-crystalline block copolymers were synthesized and characterized. The morphology of the block copolymers could be controlled by varying the chemical microstructure of the polyester segment. Solvent resistance was shown to improve as the level of crystallinity was increased. Segmented block copolymers of an amorphous polyarylester and polydimethylsiloxane were also investigated. Both the random-block and perfectly alternating synthetic routes were used and it was found that the perfectly alternating technique produced a more regular morphology; than the random-block technique. A study was also carried out on the incorporation of small amounts of polysulfone-polydimethylsiloxane block copolymers blended into homopolysulfone. Improved fracture toughness was observed without a significant loss of stiffness. The morphology of block copolymer particles dispersed in the polysulfone matrix was directly observed through transmission electron microscopy. / Ph. D.

The Variable Temperature Size Exclusion Chromatography (VTSEC) was used to study the dilute solution properties of various homo- and block copolymers as well as polymer blends, focus being primarily on the configuration-dependent properties such as average chain dimensions and hydrodynamic behavior of polymers. The study constituted of three parts. In the first part, the dilute solution properties of a series of poly(alkyl methacrylates) with varying side alkyl(ester) group were investigated as to the effect of the size of the side group on the average chain dimensions at various temperatures. The VTSEC results were found to reveal that the effect of the side group depends on the extent of chain flexibility imparted by the side group. In the second part, VTSEC was employed to investigate the applicability and validity of the various models for block copolymers in solution. For this purpose, several series of samples (all anionically synthesized) with various composition and molecular weight were used: i) poly(alkyl methacrylates), their diblock copolymers and blends and ii) diblock and triblock copolymers of poly(styrene/substituted styrene) and poly(butadiene/isoprene). VTSEC results showed that the applicability of each model to a block copolymer in solution depends on the compatibility among the components, the composition of the samples, the solvating power of the solvent used and the operating temperature. Micellization in the hydrocarbon diblock copolymer solutions was found to occur in selective solvent, its extent depending on the solubility parameter difference between the components, molecular weight, composition and solvent power. In the third part, poly(methyl methacrylate) samples with varying tacticities were studied as to the effect of stereochemical configuration on their dilute solution behavior and found to indicate that both syndiotactic and isotactic stereosequences are required for stereoassociation. Two new VTSEC data reduction procedures were devised in order to correct for the temperature drifts due to instrumentation in the first and to neutralize the effect of molecular weight in the second. In the second, termed as the Molecular Weight-Elution Volume Superposition Procedure, the effect of molecular weight alone was enutralized leaving only the effect of the intrinsic character (such as the size of the side group) of the sample in the elution behavior. Numerical computations, using the Matxrix Generation method based on the Rotational Isomeric State approximation, were carried out for stereoregular chains in order to evaluate their chain dimensions at various temperatures. / Ph. D.

The accuracy and utility of using Inverse Gas Chromatography (IGC) to characterize the microphase structure of block copolymers, and the strength of the thermodynamic interactions between the components of polymer blends and the unlike segments of block copolymers was examined. There were three parts to the study. First, the Scott ternary solution model, which is used for the study of thermodynamic interactions in polymer blends, was extended to low molecular weight mixtures. From vapor-liquid equilibrium data in the literature, the Gibbs free energy of mixing of binary mixtures (G_M ) calculated with the model were compared to experimental values. Mixtures containing ketones, aromatics hydrocarbons, chlorinated hydrocarbons, alcohols and water were studied. With the exception of mixtures containing water and low molecular weight alcohols, a fair to good correlation between theoretical and experimental values was observed. Second, the Gibbs free energy of mixing of nitrocellulose, polyvinyl chloride and poly(vinylidene fluoride) containing blends were measured with the Scott model from IGC data. For the nitrocellulose containing blend, the calculated Gibbs free energy of mixing values were large in magnitude (-2.0 to -5.0 calories/gram) and in fair agreement with the experimental heats of mixing determined from microcalorimetry measurements. For the remaining blends, the IGC data could not be distinguished from the results normally obtained for immiscible blends. The calculated G_M values were small in magnitude relative to the experimental error of the quantities. Concerning the block copolymers, the relative incompatibility of the constituent blocks of perfectly alternating block copolymers of polydimethylsiloxane and bis-A-polycarbonate and styrene-isoprene-styrene triblock copolymers was reflected in the measured G_M values. Overall, it was concluded that IGC is a good method for characterizing thermodynamic interaction between blend and copolymer constituents, but a severe limitation of the method is that the interactions are often too weak to measure accurately. Finally, the microphase structure of the above copolymers were studied by IGC from the retention behavior of hydrocarbon probes below the upper glass transition temperature of the copolymers. The degree of microphase separation, the size of the hard phases and the continuity of the soft phases in the copolymers characterized, and the results obtained were consistent with small angle x-ray, electron microscopy and differential scanning calorimetry data on the same materials. / Doctor of Philosophy

Yes / 2D materials such as graphene, LAPONITE® clays or molybdenum disulfide nanosheets are of extremely high interest to the materials community as a result of their high surface area and controllable surface properties. While several methods to access 2D inorganic materials are known, the investigation of 2D organic nanomaterials is less well developed on account of the lack of ready synthetic accessibility. Crystallization-driven self-assembly (CDSA) has become a powerful method to access a wide range of complex but precisely-defined nanostructures. The preparation of 2D structures, however, particularly those aimed towards biomedical applications, is limited, with few offering biocompatible and biodegradable characteristics as well as control over self-assembly in two dimensions. Herein, in contrast to conventional self-assembly rules, we show that the solubility of polylactide (PLLA)-based amphiphiles in alcohols results in unprecedented shape selectivity based on unimer solubility. We use log Poct analysis to drive solvent selection for the formation of large uniform 2D diamond-shaped platelets, up to several microns in size, using long, soluble coronal blocks. By contrast, less soluble PLLA-containing block copolymers yield cylindrical micelles and mixed morphologies. The methods developed in this work provide a simple and consistently reproducible protocol for the preparation of well-defined 2D organic nanomaterials, whose size and morphology are expected to facilitate potential applications in drug delivery, tissue engineering and in nanocomposites. / University of Warwick, Materials GRP, EPSRC, The Royal Society, ERC

Yes / Developing medical devices that resist bacterial attachment and subsequent biofilm formation is highly desirable. In this paper, we report the optimization of the molecular structure and thus material properties of a range of (meth)acrylate copolymers which contain monomers reported to deliver bacterial resistance to surfaces. This optimization allows such monomers to be employed within novel coatings to reduce bacterial attachment to silicone urinary catheters. We show that the flexibility of copolymers can be tuned to match that of the silicone catheter substrate, by copolymerizing these polymers with a lower Tg monomer such that it passes the flexing fatigue tests as coatings upon catheters, that the homopolymers failed. Furthermore, the Tg values of the copolymers are shown to be readily estimated by the Fox equation. The bacterial resistance performance of these copolymers were typically found to be better than the neat silicone or a commercial silver containing hydrogel surface, when the monomer feed contained only 25 v% of the “hit” monomer. The method of initiation (either photo or thermal) was shown not to affect the bacterial resistance of the copolymers. Optimized synthesis conditions to ensure that the correct copolymer composition and to prevent the onset of gelation are detailed. / Impact Accelerators Account at the University of Nottingham; Camstent Ltd; The Wellcome Trust (ref 085245 and 103882)

Yes / In this work we report a facile method to prepare a fluorescence active self-healable hydrogel via incorporation of fluorescence responsive ionic block copolymers (BCPs). Ionic block copolymers were prepared via a combined effect of ring opening polymerization (ROP) of ε-caprolactone and xanthate mediated reversible addition–fragmentation chain transfer (RAFT) polymerization. Here polycaprolactone (PCL) was modified with xanthate to prepare a PCL based macro-RAFT agent and then it was utilized to prepare block copolymers with cationic poly(2-(methacryloyloxy)ethyltrimethyl ammonium chloride) (PCL-b-PMTAC) and anionic poly(sodium 4-vinylbenzenesulfonate) (PCL-b-PSS). During the block formation, the cationic segments were randomly copolymerized with a trace amount of fluorescein O-acrylate (FA) (acceptor) whereas the anionic segments were randomly copolymerized with a trace amount of 9-anthryl methylmethacrylate (AMMA) (donor) to make both the segments fluorescent. The block copolymers form micelles in a DMF : water mixture (1 : 4 volume ratio). The ionic interaction of two BCPs was monitored via Förster resonance energy transfer (FRET) and zeta potential measurements. The oppositely charged BCPs were incorporated into a polyacrylamide (PAAm) based hydrogel that demonstrated self-healing behavior and is also highly fluorescent. / IIT Kharagpur and MRC (MR/N501888/2)