Video summarizing Ph.D. dissertation for a non-specialist audience. / National Science Foundatio (Grant No. 0846861) / Civil and Environmental Engineering / College of Engineering

Sustainability presents a pathway for future generations to have a better life. Cradle to cradle methodology is the essence of sustainability. In cradle to cradle approach, we aim to reuti-lize a given waste instead of disposing or landfilling it. Each year, millions of waste tires are dis-posed of in landfills. This poses a major challenge environmentally and economically. Environ-mentally, those tires become prone to fire hazards as well as being a place for rodents and mos-quitos to reside at. Economically, on the other hand, each tire has an average of about 50% valu-able polymers as well as oily components. One of the methods to utilize the valuable raw materi-als in waste tires is to recycle it in the form of ground tire rubber also known as crumb rubber modifier (CRM). Although CRM has been widely used as an asphalt modifier, however, due to the complexity of asphalt as well as the waste nature of CRM, the full understanding of the CRM modification mechanism with asphalt has not been fully understood. Understanding of the modi-fication mechanisms involved in the CRM interaction with asphalt would enable us to produce a crumb rubber modified asphalt (CRMA) with enhanced properties. In the current research work, an attempt is made to better understand the mechanism of interaction between CRM and asphalt and the nature of components from asphalt and CRM that take part in the interaction between them. In addition, we investigate the effectiveness of CRM as a modifier for asphalt on the mac-ro and microscale aspects. Another part of the current research work deals with a second waste material; used motor oil. Used motor oil (UMO) presents yet another challenge to environment. With the ever increas-ing motor vehicles produced with advanced technologies and increased advanced motor oil de-mand. This presents a burden on the environment, with the continuous production of UMO. In the current research work, we investigated the feasibility of utilizing UMO as a modifier for asphalt and CRMA. We also investigated the effect of UMO on the micro and macroscale aspects of asphalt.

Recycling of millions of scrap tires produced everyday is crucial challenge encountered by waste management systems. Recycling tire rubbers in form of ground tire rubber, known as crumb rubber modifier (CRM), in asphalt industry was introduced in early 1960's and is proved as an effective recycling method. Interaction between CRM and asphalt is physical in nature which happens mainly due to exchange of components between CRM and asphalt and enhances the time temperature dependant properties of asphalt. In this work, the interaction between CRM and asphalt was evaluated through monitoring the evolutions of CRM in asphalt in macro and micro-level. The mechanism and extent of CRM dissolution were monitored under several interaction conditions. The composition of materials released from CRM was investigated using thermo-gravimetric analysis (TGA). The molecular status of the released components were studied using gel permeation chromatography (GPC) analysis. The composition analysis indicated that the CRM start releasing its polymeric components into the asphalt matrix at dissolutions higher than 20%. The released polymeric component of CRM alters the microstructure of the asphalt and creates an internal network at certain interaction temperatures according to viscoelastic analysis. At these temperatures, the released polymeric components are at their highest molecular weight based on GPC results. The effect of released components of CRM on the time temperature dependent properties of asphalt and its glass transition kinetic was monitored using dynamic shear rheometer (DSR) and differential scanning calorimetry (DSC), respectively. The DSC results showed that the intensity of glass transition of the asphalt binder which is mainly defined by the aromatic components in asphalt reduced by absorption of these components by CRM. The evolution of CRM was investigated during short-term aging of the modified asphalt binder. In addition, the effect of presence of CRM and release of its component on oxidization of asphalt binder was evaluated using Fourier transform infrared spectroscopy (FTIR). The results revealed that CRM continue absorbing the aromatic components of asphalt during aging which stiffen the asphalt binder. Also, it was observed that release of oily components of the CRM, which contain antioxidant, reduces oxidization rate of asphalt significantly. / National Science Foundatio (Grant No. 0846861)

Asphalt-rubber mixtures have been shown to have useful properties with respect to distresses observed in asphalt concrete pavements. The most notable change in properties is a large increase in viscosity and improved low-temperature cracking resistance. Warm mix additives can lower production and compaction temperatures. Lower temperatures reduce harmful emissions and lower energy consumption, and thus provide environmental benefits and cut costs. In this study, the effects of crumb rubber modification on various asphalts such as California Valley, Boscan, Alaska North Slope, Laguna and Cold Lake were also studied. The materials used for warm mix modification were obtained from various commercial sources. The RAF binder was produced by Imperial Oil in their Nanticoke, Ontario, refinery on Lake Erie. A second commercial PG 52-34 (hereafter denoted as NER) was obtained/sampled during the construction of a northern Ontario MTO contract. Some regular tests such as Dynamic Shear Rheometer (DSR) and Bending Beam Rheometer (BBR), Multiple Stress Creep Recovery (MSCR) and some modified new protocols such as the extended BBR test (LS-308) and the Double-Edge Notched Tension (DENT) test (LS-299) are used to study, the effect of warm mix and a host of other additives on rheological, aging and failure properties. A comparison in the properties of RAF and NER asphalts has also been made as RAF is good quality asphalt and NER is bad quality asphalt. From the studies the effect of additives on chemical and physical hardening tendencies was found to be significant. The asphalt samples tested in this study showed a range of tendencies for chemical and physical hardening. / Thesis (Master, Chemistry) -- Queen's University, 2014-01-30 11:56:43.978

The study deals with the formulation development and thermorheological properties of crumb rubber/ethylene vinyl acetate (EVA) modified bitumen with the aim of optimizing the amount of crumb rubber and EVA loadings in bitumen based on thermorheological parameters complex shear modulus, phase angle and rutting parameter. In the modified binders EVA offers plastomer properties whereas the crumb rubber confers elasticity to the bitumen. 13.75% crumb rubber and 2.5% EVA loadings based on aging indices gave the best optimized mixture. The thermorheological behaviour of the best optimized mixture was compared to industrial grade EVA (AP-1) and crumb rubber (AR-1) modified bitumen. Improving aging behaviour of the bitumen was evaluated using four antioxidants: carbon black, hydrated lime, Irganox 1010 and Irgafos 168. The least aging indices at 58˚C and 64˚C were obtained from a 1:1:1 Irganox 1010/hydrated lime/carbon black mixture. SARA (saturates, aromatics, resins and asphaltene) analysis gave the chemical background for application of antioxidants to reduce the propensity of short term aging. To further improve the EVA/crumb rubber optimized mixture for workability FT wax (Sasobit®) was assayed at loadings from 0-2.5%. This was done to match the EVA content and maintain the original maximum loading of 2.5% in the optimized mixture. The phase change abilities of FT wax owing to the high latent heat enabled co-crystallization with the EVA with the elastomeric backbone of crumb rubber acting as support material. The energy-sustainability nexus was found to have worked at less than 1% loading of FT wax in the EVA/crumb rubber modified bitumen. Response surface methodology approach to all the sections of work was used to come up with the optimized mixtures based on rheological parameters complex shear modulus, phase angle and rutting parameter at test temperature 64˚C. The interaction chemistry of bitumen, crumb rubber, EVA and FT wax was found to be first and second order in all cases involving individual contributions and co-interaction amongst the factors. Project costing for each section of work (optimizing section, antioxidant section and FT wax section) was conducted involving the raw materials used, equipment used, labour involved and other costs incurred for all the project work.

abstract: ABSTRACT Pre-treated crumb rubber technologies are emerging as a new method to produce asphalt rubber mixtures in the field. A new crumb rubber modifier industrially known as "RuBind" is one such technology. RuBindTM is a "Reacted and Activated Rubber" (RAR) that acts like an elastomeric asphalt extender to improve the engineering properties of the binder and mixtures. It is intended to be used in a dry mixing process with the purpose of simplifying mixing at the asphalt plant. The objectives of this research study were to evaluate the rheological and aging properties of binders modified with RuBindTM and its compatibility with warm mix technology. Two binders were used for this study: Performance Grade (PG) 70-10 and PG 64-22, both modified with 25% by weight of asphalt binder. Laboratory test included: penetration, softening point, viscosity, Dynamic Shear Rheometer (DSR) and Bending Beam Rheometer (BBR). Tests were conducted under original, short and long -term aging conditions. Observations from the test results indicated that there is a better improvement when RuBindTM is added to a softer binder, in this case a PG 64-22. For short-term aging, the modified binder showed a similar aging index compared to the control. However, long term aging was favorable for the modified binders. The DSR results showed that the PG 64-22 binder high temperature would increase to 82 °C, and PG 70-10 would be increased to 76 °C, both favorable results. The intermediate temperatures also showed an improvement in fatigue resistance (as measured by the Superpave PG grading parameter |G*|sinä). Test results at low temperatures did not show a substantial improvement, but the results were favorable showing reduced stiffness with the addition of RuBindTM. The evaluation of warm mix additive using EvothermTM confirmed the manufacturer information that the product should have no negative effects on the binder properties; that is the modified binder can be used in a warm mix process. These results were encouraging and the recommendation was to continue with a follow up study with mixture tests using the RuBindTM modified binders. / Dissertation/Thesis / M.S. Civil and Environmental Engineering 2014

abstract: Crumb rubber use in asphalt mixtures by means of wet process technology has been in place for several years in the United States with good performance record; however, it has some shortcomings such as maintaining high mixing and compaction temperatures in the field production. Organosilane (OS), a nanotechnology chemical substantially improves the bonding between aggregate and asphalt by modifying the aggregate structure from hydrophilic to hydrophobic contributing to increased moisture resistance of conventional asphalt mixtures. Use of Organosilane also reduces the mixing and compaction temperatures and facilitates similar compaction effort at lower temperatures. The objective of this research study was first to perform a Superpave mix design for Crumb Rubber Modified Binder (CRMB) gap-graded mixture with and without Organosilane; and secondly, analyse the performance of CRMB mixtures with and without Organosilane by conducting various laboratory tests. Performance Grade (PG) 64-22 binder was used to create the gap-graded Hot Mix Asphalt (HMA) mixtures for this study. Laboratory tests included rotational viscometer binder test and mixtures tests: dynamic modulus, flow number, tensile strength ratio, and C* fracture test. Results from the tests indicated that the addition of Organosilane facilitated easier compaction efforts despite reduced mixing and compaction temperatures. Organosilane also modestly increased the moisture susceptibility and resistance to crack propagation yet retaining equal rutting resistance of the CRMB mixtures. / Dissertation/Thesis / Masters Thesis Civil, Environmental and Sustainable Engineering 2018

abstract: Concrete columns constitute the fundamental supports of buildings, bridges, and various other infrastructures, and their failure could lead to the collapse of the entire structure. As such, great effort goes into improving the fire resistance of such columns. In a time sensitive fire situation, a delay in the failure of critical load bearing structures can lead to an increase in time allowed for the evacuation of occupants, recovery of property, and access to the fire. Much work has been done in improving the structural performance of concrete including reducing column sizes and providing a safer structure. As a result, high-strength (HS) concrete has been developed to fulfill the needs of such improvements. HS concrete varies from normal-strength (NS) concrete in that it has a higher stiffness, lower permeability and larger durability. This, unfortunately, has resulted in poor performance under fire. The lower permeability allows for water vapor to build up causing HS concrete to suffer from explosive spalling under rapid heating. In addition, the coefficient of thermal expansion (CTE) of HS concrete is lower than that of NS concrete. In this study, the effects of introducing a region of crumb rubber concrete into a steel-reinforced concrete column were analyzed. The inclusion of crumb rubber concrete into a column will greatly increase the thermal resistivity of the overall column, leading to a reduction in core temperature as well as the rate at which the column is heated. Different cases were analyzed while varying the positioning of the crumb-rubber region to characterize the effect of position on the improvement of fire resistance. Computer simulated finite element analysis was used to calculate the temperature and strain distribution with time across the column's cross-sectional area with specific interest in the steel - concrete region. Of the several cases which were investigated, it was found that the improvement of time before failure ranged between 32 to 45 minutes. / Dissertation/Thesis / M.S. Mechanical Engineering 2011

abstract: Crumb rubber use in asphalt mixtures using wet process technology has been in practice for years in the United States with good performance history; however, it has some drawbacks that include the need for special blending equipment, high rubber-binder temperatures, and longer waiting time at mixing plants. Pre-treated crumb rubber technologies are emerging as a new method to produce asphalt rubber mixtures in the field. A new crumb rubber modifier known as Reacted and Activated Rubber (RAR) is one such technology. RAR (industrially known as “RARX”) acts like an Enhanced Elastomeric Asphalt Extender to improve the engineering properties of the binder and mixtures. It is intended to be used in a dry mixing process with the purpose of simplifying mixing at the asphalt plant. The objective of this research study was first to perform a Superpave mix design for determination of optimum asphalt content with 35% RAR by weight of binder; and secondly, analyse the performance of RAR modified mixtures prepared using the dry process against Crumb Rubber Modified (CRM) mixtures prepared using the wet process by conducting various laboratory tests. Performance Grade (PG) 64-22 binder was used to fabricate RAR and CRM mixtures and Performance Grade (PG) 70-10 was used to fabricate Control mixtures for this study. Laboratory tests included: Dynamic Modulus Test, Flow Number Test, Tensile Strength Ratio, Axial Cyclic Fatigue Test and C* Fracture Test. Observations from test results indicated that RAR mixes prepared through the dry process had excellent fatigue life, moisture resistance and cracking resistance compared to the other mixtures. / Dissertation/Thesis / Masters Thesis Civil, Environmental and Sustainable Engineering 2018

abstract: It is common to use crumb rubber as modifier in bitumen. Good performance of crumb rubber in bitumen has been reported in terms of improving characteristics like higher skid resistance, reducing noise, higher rutting resistance and longevity. However, due to the vulcanization, the polymeric crosslinked structure of crumb rubber suffers from inadequate dispersion and incompatibility in bitumen where storage stability becomes an issue. To solve this problem, partial surface devulcanization of the rubber via chemical and microbial surface activation was examined in this study showing both method can be effective to enhance rubber-bitumen interactions and subsequently storage stability of the rubberized bitumen. To ensure proper surface activation, it is important to thoroughly understand chemo-mechanics of bitumen containing rubber particles as well as underlying interaction mechanism at the molecular level. Therefore, this study integrates a multi-scale approach using density functional theory based computational modeling and laboratory experiments to provide an in-depth understanding of the mechanisms of interaction between surface activated rubber and bitumen. To do so, efficacy of various bio-modifiers was examined and compared it terms of both surface activation capability and durability of resulting rubberized bitumen. It was found that biomodifiers with various compositions can have either synergistic or antagonistic effect onchemo-mechanics of rubberized bitumen. The study was further extended to study the interplay of Polyphosphoric Acid (PPA) and these biomodified rubberized bitumens showing not all modifiers have high synergy with PPA in bitumens. Finally, durability of rubberized bitumen was studied in terms of its resistance to Ultraviolet (UV) aging. It was shown that there is a strong relation between composition of biomodified rubberized bitumen and its resistance to UV-aging. / Dissertation/Thesis / Doctoral Dissertation Civil, Environmental and Sustainable Engineering 2020