This thesis presents a new output passive filter for voltage source inverter applications which is based on a shunt connected single tuned filter topology. The proposed circuit has the advantage of tracing harmonic components wherever its location in the frequency spectrum. The change in the harmonic location might be as a result of a change in the inverter operating frequency. Also, the proposed filter achieves harmonic reduction close to the traditional single tuned passive filter. In order to show the superiority of the proposed model, a comparison is introduced with other self tuning harmonic filters showing merits and drawbacks of each technique. The proposed circuit (when integrated in square wave inverter) has also shown a tremendous reduction in the switching losses in comparison with high frequency Pulse Width Modulation inverter. Mathematical analyses showing the design of the proposed filter together with extensive simulation results to verify the design are also introduced. The practical implementation of the system is presented and the results show excellent agreement with the theory and simulation. In order to appreciate the proposed filter a new method for classifying passive power filters is introduced. The review includes a comparison of these configurations showing their merit and drawbacks.

This thesis presents a new DC/AC inverter circuit which is based on a switched-capacitor circuit topology with reduced components (power switch and capacitor) count for low power applications. The proposed circuit has distinct features of both voltage boost-up and near sinusoidal (multi-level/staircase) AC output voltage. The main idea is to utilise a simple circuit technique called resonant-based Double Switch Single Capacitor Switched-Capacitor (DSSC SCC) with variable duty cycle Pulse Width Modulation (PWM) control technique in such a way that multi-level voltage can be realised across a capacitor. In order to show the superiority of the applied technique, comparisons with other techniques/circuits configurations are presented. The circuit technique can significantly reduce the number of multiple stages of switched-capacitor circuit cells of the recent switched-capacitor multi-level inverter topology. The proposed inverter (with integrated DSSC SCC technique) can generate a line-frequency with 13-levels near sinusoidal AC output voltage with low total harmonics distortion. The output voltage can be achieved with the least number of components use and only a single DC source is used as an input. The proposed inverter topology is also reviewed against other inverter-based switched-capacitor circuit topology and the well-known multi-level inverter topology. The proposed inverter has shown a tremendous reduction in the total harmonics distortion and circuit component count in comparison with the recent Switched-Capacitor Boost multi-level inverter and the classical Cascaded H-Bridge multi-level inverter. Mathematical analysis shows the design of the proposed inverter and PSPICE simulation result to verify the design is also presented. The practical experiment implementation of the proposed system is presented and proves the correct operation of the proposed inverter topology by showing consistency between simulation results and practical results.

The grid-connected photo-voltaic (PV) system is one of the most promising renewable energy solutions which offers many benefits to both the end user and the utility network and thus it has gained the popularity over the last few decades. However, due to the very nature of its invariability and weather dependencies, the large scale integration of this type of distributed generation has created challenges for the network operator while maintaining the quality of the power supply and also for reliable and safe operations of the grids. In this study, the behavioral impact of large scale PV system integration which are both steady and dynamic in nature was studied.  An aggregate PV model suited to study the impacts was built using MATLAB/Simulink.  The integration impacts of PV power to existing grids were studied with focus on the low voltage residential distribution grids of Mälarenergi Elnät AB (10/0.4 kV). The steady state impacts were related to voltage profile, network loss. It was found that the PV generation at the load end undisputedly improves the voltage profile of the grid especially for the load buses which are situated at farther end of the grid. Further, with regard to the overvoltage issue, which is generally a concern during the low load demand period it was concluded that, at a 50% PV penetration level, the voltage level for the load buses is within the limit of 103% as prescribed by the regulator excepting for few load buses. The voltage level for load buses which deviate from the regulatory requirement are located at distance of 1200 meter or further away from the substation. The dynamic impact studied were for voltage unbalancing in the grid, which was found to have greater impact at the load buses which is located farther compared to a bus located nearer to the substation. With respect to impact study related to introduction of harmonics to the grid due to PV system integration, it was found that amount of harmonic content which was measured as total harmonic distortion (THD) multiplies with integration of more number of PV system. For a 50 % penetration level of PV, the introduced harmonics into the representative network is very minimal. Also, it was observed from the simulation study that THD content are be less when the grid operates at low load condition with high solar irradiance compared to lower irradiance and high load condition.

In this thesis is presented detail design of power part of DC/DC converter and output inverter. This device will serve for creating an artificial network in a family house where it will be used for supplying selected household appliances which are designed for use in AC network. The converter will be supplied with DC voltage. This tension will be obtained from a system of photovoltaic panels. The output voltage will have alternate character and it will be close to the network voltage 230 V/50 Hz. In the introductory part of thesis are discussed possible topologies of converters and output inverters. Subsequently are designed individual parts of supply inverter. In the final part there are shown waveforms of important values and is given a thesis evaluation.

The aim of this project is to describe, design and create a converter from 12V DC to 230 VRMS. The power of this device is about 500W. The device consists of two main converters. The first one is step-up DC/DC converter and the other is DC/AC inverter. Step-up converter is designed as a resonant converter. It is useful for pushing down losses in semiconductors and inceasing efficiency. The inverter is changing DC voltage from the first converter to AC voltage. Control of this device is realized with DSP Motorola. This device should be used mainly for supply common devices up to 500W. Main usage is planed in a car or to another place where is not posible to connect some device to plug.

This work is focused on single phase inverters, which are used for the conversion of the direct current to the alternating current and are nowdays used especially in systems of back-up power supply. The specific aim of this work is implementation of design hight power circuit of inverter include calculation of control algorithm. It describes the complete solution of power circuit. Next step is a analysis of problems concerning the digital control with help of signal processor which is used for solution of regulator structure. Check of the design and checkout of control algorithm is made in the form of simulation in the MATLAB Simulink. Debugged program algorithm is subsequently implemented into the signal microprocessor. The work results rate estimation functionality of inverter and solution of control algorithm.