71 |
Steady state analysis of soft-switching DC-DC and magamp forward convertersAlsharqawi, Abdelhalim M. 01 July 2002 (has links)
No description available.
|
72 |
Constant-frequency, clamped-mode resonant convertersTsai, Fu-Sheng January 1989 (has links)
Two novel clamped-mode resonant converters are analyzed. These clamped-mode converters operate at a constant frequency while retaining many desired features of conventional resonant converters such as fast responses, zero-voltage turn-on or zero-current turn-off, and low EMI levels, etc. The converters are able to regulate the output from no load to full load and are particularly suitable for off-line, high-power applications.
To provide insights to the operations and derive design guidelines for the clamped-mode resonant converters, a complete dc characterization of both the clamped-mode series-resonant converter and the clamped-mode parallel-resonant converter, operating above and below resonant frequency, is performed. State-plane analysis techniques are employed. By portraying the converters' operation on a state-plane diagram, various circuit operating modes are identified. The boundaries between different operating modes are determined. The regions for natural and force commutation of the active switches are defined. Important dc characteristics, such as control-to-output transfer ratio, rms inductor current, peak capacitor voltage, rms switch currents, average diode currents, switch turn-on currents, and switch turn-off currents are derived to facilitate the converter designs.
To illustrate the converter designs in different operating regions, several design examples are given. Finally, three prototype circuits are built to verify the analytical results. / Ph. D.
|
73 |
Simulation of spacecraft power systems using a modular state variable approachNelms, Robert Mark January 1987 (has links)
The power requirements for future spacecraft power systems will be on the order of a few hundred kilowatts to a few megawatts. Because of these power levels, a high-voltage, high-power distribution subsystem may be utilized to transmit power from the source to the different loads. Using current state-of-the-art power conditioning electronics, complex series and parallel configurations will be required at the interface between the source and the distribution subsystem and between the distribution subsystem and the loads.
The dynamic response of such a spacecraft power system may be obtained using a general purpose program such as SPICE2. However, for large and complex spacecraft power systems, the input file will be large and complex with correspondingly large computation times. As an alternative, the spacecraft power system can be considered as an interconnection of modular components. Each component is treated as a two-port network, and a state model is written with the port voltages as the inputs. The state model of each component is solved using the state transition matrix and assuming that the port voltages are . clamped for each time step. This calculation proceeds as if all two-port networks are decoupled. After the state variables have been updated, the inputs to all components are calculated using network analysis principles. The solution procedure alternates between solving the dynamic model of all components and the network equations for the component inputs.
The modular state variable approach and SPICE2 are compared using two example systems. This comparison shows the advantages of the modular state variable approach. First, for the modular state variable approach the system is considered as an interconnection of modular components. In SPICE2, the system is treated as an interconnection of circuit elements. As a result, the system description for large and complex spacecraft power systems is much _ larger and more complex than a modular state variable description. Secondly, the modular state variable approach requires less CPU time than SPICE2. For one of the example systems presented here, the modular state variable approach uses one-twentieth of the CPU time used by SPICE2. / Ph. D.
|
74 |
Topology and analysis in power conversion and inversionTymerski, Richard P. E. January 1988 (has links)
Basic PWM dc-to-dc converter structure is examined wherein a basic substructure of converters, known as a converter cell, is identified. Converter cells can be used in generation and classification of basic PWM dc-to-dc converters. A large number of new converters are generated.
Converter analysis, whereby the nonlinear response of the system to perturbations in the control or the input, is determined by two different methods.
A classical approach to nonlinear systems analysis is first used wherein the system is represented by a Volterra functional series. The alternative approach presented concentrates on deriving circuit models for the PWM switch. The PWM switch represents the static nonlinear substructure of the vast majority of converter cells. Analysis of converters then proceeds in an analogous fashion to ordinary transistor circuit analysis whereby the nonlinear device is replaced by its circuit model.
Topological considerations of single-phase dc-to-ac inverters are discussed. A number of zero-current switching quasi-resonant inverter topologies are derived. Schemes that permit these topologies to handle reactive loads are identified. / Ph. D.
|
75 |
Complete and Exact Small Signal Analysis of DC-to-DC Switched Power Converters Under Various Operating Modes and Control MethodsSimmons, Justin French 01 January 2011 (has links)
A method to obtain the exact control-to-output and input-to-output transfer functions for switched DC-to-DC pulse-width modulated power converters is applied to different combinations of operating conditions such as continuous conduction mode (CCM), discontinuous conduction mode (DCM), and discontinuous voltage mode (DVM) and methods of control such as normal voltage mode (NVM), current programming mode (CPM), and V-squared control. The majority of these combinations have not previously had their transfer functions of interest derived to the accuracy provided by the method. The derivation of the method is covered, and the results from its application are verified by simulation. The simulation method is also justied and proposed as an improvement to the methods used by simulation engines for switched mode power supply design such as SIMPLIS.
|
76 |
MEMS-based fabrication of power electronics components for advanced power convertersGallé, William Preston 24 August 2012 (has links)
Fabrication technology, based on MEMS processes, for constructing components for use in switched-mode power supplies are developed and presented. Capacitors, magnetic cores, and inductors based on sacrificial multilayer electroplating are designed, fabricated, and characterized. Characterization of the produced inductors' core losses at high frequency and high flux is presented, confirming the aptness of the featured microfabrication processes for reducing eddy current losses in magnetic cores. As well, the demonstration of the same inductors in DC/DC converters at high switching frequencies, up to 6 MHz, is presented.
Initial work addressing the top-down development of a fully-integrated DC/DC converter is presented. As well, the comprehensive advancement of the central process - sacrificial multilayer electroplating - is presented, including the development of a second-generation automated multilayer electroplating system. The advanced sacrificial multilayer plating process is applied to produce microfabricated capacitors, which achieved in excess of 1.5 nF/mm² capacitance density,
The fabrication of highly-laminated magnetic cores and power inductors based on sacrificial multilayer electroplating is presented, along with the design and development of a system for characterizing inductor behavior at high-frequency, high-flux conditions. The design and operation of both buck and boost DC/DC converters, switching at up to 6 MHz, built around these highly-laminated-core inductors are presented.
|
77 |
Submicron CMOS programmable analog floating-gate circuits and arrays using DC-DC convertersHooper, Mark S. January 2005 (has links) (PDF)
Thesis (Ph. D.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2005. / Kucic, Matthew, Committee Member ; Hasler, Paul, Committee Chair ; Heck, Bonnie, Committee Member ; Cressler, John, Committee Member ; Anderson, David, Committee Member. Vita. Includes bibliographical references.
|
78 |
Chaos In Switched Mode D.C - D.C ConvertersParvati, R 01 1900 (has links) (PDF)
No description available.
|
79 |
Control Strategy For Maximizing Power Conversion Efficiency And Effectiveness Of Three Port Solar Charging Station For Electric VehiclesHamilton, Christopher 01 January 2010 (has links)
Recent trends in the energy sector have provided opportunities in the research of alternative energy sources and optimization of systems that harness these energy sources. With the rising cost of fossil fuel and rising concern about detrimental effects that fossil fuel consumption has on the environment, electric vehicles are becoming more prevalent. A study put out in 2009 gives a prediction that in the year 2025, 20% of new vehicles will be PHEVs.[1] As energy providers become more concerned about a growing population and diminishing energy source, they are looking into alternative energy sources such as wind and solar power. Much of this is done on a large scale with vast amounts of land used for solar or wind farms to provide energy to the grid. However, as population grows, requirements of the physical components of a power transmission system will become more demanding and the need for remote micro-grids will become more prevalent. Micro-grids are essentially smaller subsystems of a distribution system that provide power to a confined group of loads, or households. Using the idea of micro grid technology, a solar charging station can be used as a source to provide energy for the immediate surroundings, or also to electric vehicles that are demanding energy from the panels. Solar charging stations are becoming very popular, however the need for improvement and optimization of these systems is needed. This thesis will present a method for redesigning the overall architecture of the controls and power electronics of typical carports so that efficiency, reliability and modularity are achieved. Specifically, a typical carport, as seen commonly today, has been built on the University of Central Florida campus in Orlando. This iii carport was designed in such a way that shifting from conventional charging methods is made easy while preserving the fundamental requirements of a practical solar carport.
|
80 |
Power Enhancement of Piezoelectric Technology based Power Devices by Using Heat Transfer Technology / Amélioration de la puissance des transformateurs piézoélectriques par gestion de l'échauffementSu, Yu-Hao 04 July 2014 (has links)
L’objectif de cette étude est d’améliorer les performances des transformateurs piézoélectriques en terme de courant de sortie et de puissance pour des applications d’alimentation DC/DC, grâce à la gestion de l’échauffement. Le courant de sortie des transformateurs piézoélectriques, et donc la puissance transmise, sont directement liés à la vitesse de vibration qui pour des valeurs élevées engendre des pertes et une forte élévation de température. Cette élévation excessive de la température a comme conséquence le changement des caractéristiques du transformateur et plus particulièrement la diminution du facteur de qualité Q. Ainsi cela entraine une limite structurelle de la puissance transmise du transformateur. Une solution pour augmenter le courant de sortie est l’utilisation d’un redresseur doubleur de courant, qui grâce à 2 inductances permet, à courant de charge donné, de diminuer la vitesse de vibration du transformateur, mais ne permet pas de régler le problème d’échauffement du transformateur. Dans cette thèse nous proposons des moyens d’évacuation de la chaleur ainsi que le choix de l’environnement dans lequel le transformateur devra fonctionner. L’influence de différents systèmes de refroidissement d’un convertisseur DC/DC à base transformateur piézoélectrique est étudiée. L’étude thermique du transformateur piézoélectrique multicouche polarisé en épaisseur et ayant des électrodes circulaires met en évidence un comportement non linéaire. Une plaque vibrante piézoélectrique est d’abord envisagée pour créer un flux d’air qui augmente l’évacuation de chaleur par convection, puis un module de refroidissement utilisant l’effet thermoélectrique. Les mesures montrent que la première solution est plus avantageuse car elle améliore sensiblement les performances du transformateur pour un coût énergétique très faible. Une étude thermique par éléments finis complète cette étude, montrant que l’approche par schéma électrique est pertinente. La puissance que peut délivrer le transformateur sur une charge optimale est encore augmentée. Enfin, ce travail montre qu’en combinant les dispositifs de refroidissement tout en respectant la condition de température inférieure à 55°C, le rendement du convertisseur reste raisonnable (70%) et la puissance disponible peut doubler dans le meilleur des cas. / The objective of this study was to increase the output current and power in a piezoelectric transformer (PT) based DC/DC converter by adding a cooling system. It is known that the output current of PT is limited by temperature build-up because of losses especially when driving at high vibration velocity. Excessive temperature rise will decrease the quality factor Q of piezoelectric component during the operational process. Simultaneously the vibration energy cannot be increased even if under higher excitation voltage. Although connecting different inductive circuits at the PT secondary terminal can increase the output current, the root cause of temperature build-up problem is not solved.This dissertation presents the heat transfer technology to deal with the temperature build-up problem. With the heat transfer technology, the threshold vibration velocity of PT can be increased and thus the output current and output power (almost three times).Furthermore, a comparison between heat transfer technology and current-doubler rectifier applied to the piezoelectric transformer based DC/DC converter was also studied. The advantages and disadvantages of the proposed technique were investigated. A theoretical-phenomenological model was developed to explain the relationship between the losses and the temperature rise. It will be shown that the vibration velocity as well as the heat generation increases the losses. In our design, the maximum output current capacity can increase 100% when the operating condition of PT temperature is kept below 55°C. The study comprises of a theoretical part and experimental proof-of-concept demonstration of the proposed design method.
|
Page generated in 0.0882 seconds