1 |
Evaluation of tomographic methods for limestone characterization : Using synchrotron-based X-ray tomography to determine porosity, internal structure and internal distributions in limestoneAskengren, Albert January 2021 (has links)
Limestone is a raw material in the cement and quicklime industry and knowledge about limestone characteristics can help improve and optimize production processes. In the end this can lead to a reduction in CO2 emissions from the industry. In this project X-ray tomography (XRT) was used to examine limestone samples. The aim was to determine if XRT, including synchrotron-based XRT, is a reliablemethod to determine porosity, pore structure and internal distributions of pores and pyrite (FeS2) grains in limestone. The aim also included to determine if XRT could be used to resolve material variations, fine-grained and larger crystals in limestone. In total, there were ten limestone samples and the performed XRT was done by Advanced Light Source (ALS) in Berkeley, California and by Luleå University of Technology. A brief comparison between ALS and Luleå was also done by inspectingsamples that have been through XRT at both facilities. The main software used foranalysis was Avizo v.9.2.0. The results showed that XRT is a suitable method for determining porosity and pore distribution. Interactive thresholding was used in Avizo for measuring porosity. The porosity was determined as a single value and as a narrow range, where a narrow range was more reliable. XRT was also found to be a suitable method for visually determining a variety of textures within the samples. Areas with different materials(such as dolomite) and/or newly-formed crystals were visually distinguishable but individual newly-formed crystals were not as clear when compared to scanning electron microscopy. Individual older fine-grained and larger crystals were hard to resolve. Internal distributions in 3D of both pores and pyrite grains were possible to obtain with XRT. The analysis of internal distributions was found to be a clear advantage with the method of XRT. The equivalent diameter of pores and pyrite grains was also measured and plotted in histograms. The XRT performed at ALS had higher resolution than the XRT performed in Luleå (0.65 vs 2 μm). Lower resolution over-estimated the average equivalent diameter of pores, and boundaries of pores and cavities were harder to see. Therefore, the higher resolution from ALS was preferable. These results contribute to understanding limestone characteristics.
|
2 |
The application of dual energy x-ray transmissions sorting to the separation of coal from torbaniteStrydom, Hayley 17 May 2011 (has links)
PhD, Faculty of Engineering and the Built Environment, University of the Witwatersrand, 2010 / Dual Energy X-Ray Transmission (DE-XRT) Imaging is a multi-sensor technique employed to
conduct particle-by-particle sorting. The system makes use of a dual energy x-ray line scan
sensor, which generates images of the transmitted x-rays, similar to images generated for suitcase
inspection in airport security applications. The dual energy x-ray system allows for rapid
approximation of atomic number range, which is utilised to evaluate the mineral and maceral
content of a variety of minerals, including coal. The process is independent of particle surface
condition, and can thus be utilised as a dry process.
A unique application of this technology is in the removal of torbanite from a coal deposit located
in Mpumalanga, South Africa. The separation of coal from torbanite has been a problem for the
coal industry for a long time. The separation of coal and torbanite by conventional gravity
separation techniques is difficult, due to the overlapping densities of torbanite and coal. The
commercial value of both commodities is significantly compromised if contaminated with the
other, thus impacting negatively on the financial viability of mining such a deposit.
Preliminary laboratory DE-XRT testwork results on high quality coal and torbanite products were
promising. In order to evaluate the separation of typical Run of Mine (ROM) material on pilot
scale, a production scale Mikrosort X-Tract Sorter was purchased. This was the first DE-XRT
sorter available in South Africa, and was housed at Mintek in Johannesburg. A 150t sample was
provided from a box cut adjacent to the coal deposit under investigation in order to conduct bulk
and pilot sorting tests, the focus of which was on obtaining coal products of low ash and torbanite
content.
Clear distinctions between the coal, torbanite and shale fractions were observed using this
technique. The sorter feed (-80mm+20mm) could be upgraded from a CV of 22MJ/kg to
28MJ/kg. Ash content could be reduced from 26% to 10%, which meets export quality standards.
Petrographic analysis of the coal product indicated that a high purity coal product (in terms of
torbanite and ash content) was attainable (91% by volume) at a mass yield of 42.9% to the coal
product, with shale and mixed humic/sapropelic coal as contaminants. Under these conditions,
torbanite contamination was marginal.
It was demonstrated that shale could be removed from the torbanite product via a second sorting
stage. This however was not the primary focus of the study, and was not optimised for this
investigation.
Two major limitations of the sorting process were identified, viz.; poor liberation and limited
sorter feed size range. These impacted on the process as follows:-
• The effects of poor liberation on coal quality could be counteracted by adjusting the
sorting criteria of the algorithm to reject additional material. This would result in a lower
coal product mass yield. In addition, interlocked coal/shale particles would report to the
torbanite fraction.
• A significant proportion of the ROM feed reported to the -20mm size fraction, and
therefore did not fall part of the sorter feed. This resulted in a very low coal mass yield as
a proportion of the ROM feed. If this process were to be adopted, means of minimizing
fines production during mining and crushing would need to be investigated to improve
overall yield to coal product.
The capability to process coarse materials (-80mm+20mm) allows for throughputs in
excess of 40t/hr. Consequently, this technique may be applied in simpler coal upgrading
processes, such as coal deshaling in arid regions.
|
3 |
Effect of Compressive Loading on Transport Properties of Cement-Based MaterialsHoseini,Meghdad Unknown Date
No description available.
|
4 |
KOREAN ANTHRACITE COAL CLEANING BY MEANS OF DRY AND WET BASED SEPARATION TECHNOLOGIESMahmoodabadi, Majid 01 January 2015 (has links)
Korean coals are typically high rank anthracite characterized by high ash content and difficult cleaning characteristics. The main objective of the study was to evaluate the feasibility of treating various size fractions within the coal using an assortment of physical coal cleaning technologies. Dry cleaning is preferred due to the friability of the coal. As such, three pneumatic processes were tested including Ore Sorting for the plus 10 mm material, Air Table Separation for 10 x 1 mm fraction and Tribo-electric Separator for - 1 mm fraction. The Dense Medium Cyclone is known to be one of the most efficient separation processes and thus was evaluated for the cleaning of 10 x 1 mm coal.
To realize the optimum performances from the Air Table and Rotary Tribo-electric Separator, their operational variables were systematically studied using a parametric experimental design. In addition, the dense medium cyclone and X-ray Transmission Sorting trials were performed under various medium densities and separation settings, respectively. A comparison of the cleaning performance revealed that the Dense Medium Cyclone and X-ray Transmission Sorting proved to provide the most effective results with maximum ash rejection and combustible recovery. The tribo-electric separation process was ineffective while the air table provided modest ash reduction potential.
|
5 |
Geological characterization of rock samples by LIBS and ME-XRT analytical techniquesElvis Nkioh, Nsioh January 2022 (has links)
One of the major challenges in earth sciences and mineral exploration has been to determine with high accuracy and at a fast rate the elemental composition as well as the general chemistry of a rock sample. Many analytical techniques e.g., scanning electron microscopy (SEM) have been employed in the past with a certain degree of success, but their analyses usually require a lengthy sample preparation and time-consuming measurements which produce results at a much slower rate than techniques whichrequire less or do not require any sample preparation at all. SEM images the surface of a sample by scanning it with a high-energy beam of electrons in a raster scan pattern, where the primary electron beam produced under very low air pressure vacuum scans across the sample by striking it, and a variation of signals produce an image of the surface, or its elemental composition together with energy dispersive X-rays. Alternatively, laser induced breakdown spectrometry (LIBS) and multi energy X-ray transmission (ME-XRT) are non-contact measurement scanning techniques, capable of producing faster results than SEM-EDS which makes them suitable for real time measurements and analyses as they do not slow down the pace of a project being carried out. LIBS is a spectroscopic technique used to characterize and detect materials where a highly energetic laser pulse is focused onto the surfaces of solids, liquids or gases resulting in atomic and molecular species to emit light at specific wavelengths which is collected with a spectrometer and analysed using a computer. Comparably, ME-XRT is a sensor-based sorting technique involving the planar projection of X-ray attenuation of a particle stream, distributed on a fast conveyor belt, where they are scanned and evaluated while passing and an image is recorded by a line scan detector. Eleven rock samples were analysed in this study. They include four rock type samples: granite, basalt, sandstone, and gneiss, all obtained from Luleå University of Technology (LTU) sample storage and seven ore type samples which include a porphyry Cu sulphide ore, a porphyry Cu oxide ore, a porphyry Cu-Au-Ag ore, an apatite iron ore (AIO), an iron-oxide copper gold ore (IOCG), an orogenic gold ore and a volcanogenic massive sulphide ore (VMS). The SEM results give a semi-quantitative elemental composition of the rocks, which may be usedto discriminate mineralisation. Energy dispersive X-ray spectroscopy (EDS) maps may be used to identifygeological features and secondary electron (SE) images may be used to understand the topography of the rock samples. The SEM has a low penetration depth rate but produces moderate to high accuracy resultsdepending on the settings and calibrations. It requires a lengthy sample preparation, and its analytical time is often too long for routine industrial application. LIBS results also provide rock elemental compositions similar to the SEM, which may be quantitative if the same spectrometer is used for all elements and calibrated against a standard. It also produces element maps similar to the SEM-EDS maps. LIBS analyses yield high accuracy results but at a low penetration depth. There are no standard calibrations for the LIBS measurements, which limits quantification. LIBS measurements do not require any form of sample preparation. ME-XRT analyses result in rock chemical data portraying a light material fraction (aluminium-like) and a heavy material fraction (iron-like) which may be used to distinguish different rock samples based on the closeness of their effective atomic number Zeff to that of aluminium and iron respectively. It’s analysis also produces low-resolution images of the analysed rock samples. The image resolution is too low to allow interpretation of the data in the context of the structures and textures in the rock samples. It has a higher penetration depth than LIBS and SEM-EDS producing more volumetric data but with a lower accuracy in terms of the amount of information obtained. Only two elements are used for ME-XRT calibration measurements, if many elements of varying atomic numbers could be used, it would have the ability to provide a more reliable data. Samples must have a maximum and minimum thickness; thus, sample preparation is required to regulate the rock thickness. SEM and LIBS provide element compositions of minerals and element distribution maps required by geologist in their daily activities during exploration and mining. This information can be considered the most useful obtained from all three techniques. However, LIBS analyses are faster, and its maps are of higher quality even at the same resolution as the SEM-EDS. This makes the LIBS preferable for real time measurements and analyses. Geological activities like drill core logging, mine mapping and sampling for grade control all require fast results for project continuity and LIBS is suitable for this purpose as it can keep up with the pace of these activities. SEM analytical technique provides semi-quantitative data which is more accurate than the LIBS data and thus, preferable for usage in research institutions and universities.ME-XRT can reveal information on the internal structures or different rock sample compositions. This makes it a suitable technique in distinguishing ore from waste material especially in iron ore mining and processing where the iron needs to be separated from the siliceous waste and sorting is also required prior to beneficiation to avoid equipment destruction by abrasive quartz. LIBS and ME-XRT analytical techniques complement each other in terms of analytical capabilities as LIBS has a low penetration depthrate but high accuracy results while the ME-XRT has a high penetration depth rate but low accuracy results. They are both fast scanning techniques that can be used for real time measurements and analyses and if their analytical prowess can be improved, the combination of these two fast analytical techniques may enable us to obtain high quality data and may as well be what is needed by geologists in the future.
|
Page generated in 0.1572 seconds