We report the synthesis of ultra-high aspect ratio copper nanowires (CuNW) and fabrication of CuNW-based transparent conductive electrodes (TCE) with high optical transmittance (> 80%) and excellent sheet resistance (R-s < 30 Omega/sq). These CuNW TCEs are subsequently hybridized with aluminum-doped zinc oxide (AZO) thin-film coatings, or platinum thinfilm coatings, or nickel thin-film coatings. Our hybrid transparent electrodes can replace indium tin oxide (ITO) films in dye-sensitized solar cells (DSSCs) as either anodes or cathodes. We highlight the challenges of integrating bare CuNWs into DSSCs, and demonstrate that hybridization renders the solar cell integrations feasible. The CuNW/AZO-based DSSCs have reasonably good open-circuit voltage (V-oc = 720 mV) and short-circuit current-density (J(sc) = 0.96 mA/cm(2)), which are comparable to what is obtained with an ITO-based DSSC fabricated with a similar process. Our CuNW-Ni based DSSCs exhibit a good open-circuit voltage (V-oc = 782 mV) and a decent short-circuit current (J(sc) = 3.96 mA/cm2), with roughly 1.5% optical-to-electrical conversion efficiency.

Cyanine dyes that absorb light in the near infrared to far red region of the electromagnetic spectrum are desirable as photosensitizers for photodynamic cancer therapy. Light of wavelengths in this range is able to deeply penetrate tissue allowing for practical in vivo use of these dyes. A series of three structurally similar pentamethine cyanine dyes that absorb light ~800 nm to ~500 nm was tested to determine the effects of structural influences on the yields of supercoiled DNA photo-converted to nicked or linear forms. Possible mechanisms and optimal parameters for near- quantitative DNA photocleavage with a symmetrical quinoline pentamethine cyanine dye are discussed.

The long-term outdoor durability of dye-sensitized solar cells (DSSCs) is still a challenging issue for the large-scale commercial application of this promising photovoltaic technique. In order to study the degradation mechanism of DSSCs, ageing tests under selected accelerating conditions were carried out. The electrolyte is a crucial component of the device. The interactions between the electrolyte and other device components were unraveled during the ageing test, and this is the focus of this thesis. The dynamics and the underlying effects of these interactions on the DSSC performance were studied. Co(bpy)32+/3+-mediated solar cells sensitized by triphenylamine-based organic dyes are systems of main interest. The changes with respect to the configuration of both labile Co(bpy)32+ and apparently inert Co(bpy)33+ redox complexes under different ageing conditions have been characterized, emphasizing the ligand exchange problem due to the addition of Lewis-base-type electrolyte additives and the unavoidable presence of oxygen. Both beneficial and adverse effects on the DSSC performance have been separately discussed in the short-term and long-term ageing tests. The stability of dye molecules adsorbed on the TiO2 surface and dissolved in the electrolyte has been studied by monitoring the spectral change of the dye, revealing the crucial effect of cation-based additives and the cation-dependent stability of the device photovoltage. The dye/TiO2 interfacial electron transfer kinetics were compared for the bithiophene-linked dyes before and after ageing in the presence of Lewis base additives; the observed change being related to the light-promoted and Lewis-base-assisted performance enhancement. The effect of electrolyte co-additives on passivating the counter electrode was also observed. The final chapter shows the effect of electrolyte composition on the electrolyte diffusion limitation from the perspectives of cation additive options, cation concentration and solvent additives respectively. Based on a comprehensive analysis, suggestions have been made regarding lithium-ion-free and polymer-in-salt strategies, and also regarding cobalt complex degradation and the crucial role of Lewis base additives. The fundamental studies contribute to the understanding of DSSC chemistry and provide a guideline towards achieving efficient and stable DSSCs. / <p>QC 20160517</p>

Solid-state dye-sensitized solar cells (ssDSSCs) and recently developed perovskite solar cells (PSCs) have attracted a great attention in the scientific field of photovoltaics due to their low cost, absence of solvent, simple fabrication and promising power conversion efficiency (PCE). In these types of solar cell, the dye molecule or the perovskite can harvest the light on the basis of electron excitation. Afterwards, the electron and hole are collected at the charge transport materials. Photoelectrochemical polymerization (PEP) is employed in this thesis to synthesize conducting polymer hole transport materials (HTMs) for ssDSSCs. We have for the first time developed aqueous PEP in comparison with the conventional organic PEP with acetonitrile as solvent. This water-based PEP could potentially provide a low-cost, environmental-friendly method for efficient deposition of polymer HTM for ssDSSCs. In addition, new and simple precursors have been tested with PEP method. The effects of dye molecules on the PEP were also systematically studied, and we found that (a) the bulky structure of dye is of key importance for blocking the interfacial charge recombination; and (b) the matching of the energy levels between the dye and the precursor plays a key role in determining the kinetics of the PEP process. In PSCs, the HTM layer is crucial for efficient charge collection and its long term stability. We have studied different series of new molecular HTMs in order to understand fundamentally the influence of alkyl chains, molecular energy levels, and molecular geometry of the HTM on the photovoltaic performance. We have identified several important factors of the HTMs for efficient PSCs, including high uniformity of the HTM capping layer, perovskite-HTM energy level matching, good HTM solubility, and high conductivity. These factors affect interfacial hole injection, hole transport, and charge recombination in PSCs. By systematical optimization, a promising PCE of 19.8% has been achieved by employing a new HTM H11. We believe that this work could provide important guidance for the future development of new and efficient HTMs for PSCs.

With the technological progress of materials science, the palette of colours with which to print on textiles has expanded beyond those with previously known properties and expressions to a new generation, with more advanced functionality and expressive properties. This new range of colours is characterised by their ability when printed on textiles to change colour in relation to external factors and internal programmes; for example, leuco dye-based thermochromic inks generally change colour in response to temperature fluctuations. This research explores the design properties and potentials of leuco dye-based thermochromic inks printed on textiles, with regard to creating a wider range of colour-changing effects for textile applications. The significance of this for textile design is related to the development of a methodology for designing dynamic surface patterns. The research was conducted by creating a series of design experiments using leuco dye-based thermochromic inks, which resulted in different recipes and methods, along with a pedagogical tool. The results highlighted the diverse colour-changing properties of leuco dye-based thermochromic inks, which have the potential to create more complex patterns on textiles. The outcome of this research proposes a foundation for textile designers with which to approach new ways of thinking and designing.

This thesis studies parameters influencing both the performance and stability of solid state sensitized solar cells (ssSSCs). ssSSCs benefit from their low materials and manufacturing processing costs, a consequence of using solution processed materials. However, solution processed materials are often structurally and electronically disordered. By characterizing fully operational ssSSCs and their charge transport properties, this thesis elucidates the factors limiting charge transport and proposes routes towards both improved photovoltaic conversion efficiency and long-term stability. Chapter 2 provides an explanation of the operation of ssSSCs, while Chapter 3 discusses the basic methods used in this thesis. Having set this background, Chapter 4 explores the interaction between atmospheric oxygen and charge doping mechanisms in the organic semiconductors used in ssSSCs. To understand the implications of the findings presented in Chapter 4, a new technique, “transient mobility spectroscopy”, was developed to understand the evolution of balanced charge transport behaviour of disordered semiconductors at different operating conditions in ssSSCs. This technique is presented in full in Chapter 5. The understanding gained in Chapters 4 and 5 suggest that alternative light absorbers with higher extinction coefficients may be beneficial to improving the performance of ssSSCs. Chapter 6 discusses the use of an organometal trihalide perovskite, as light absorber in ssSSCs. Using time resolved techniques, the charge transport and recombination mechanisms in various device architectures are explored, allowing suggestions to be made towards future improvements. Chapter 7 uses the technique presented in Chapter 5 to understand a rapid degradation mechanism of working ssSSCs. Particular focus is placed on the titanium dioxide charge-transporting layer. Building on this newfound understanding, two methods for attaining stable photovoltaic performance are provided, a great step forward for this technology.

Metal and metal oxides are widely used in industry, and to optimize their performance their surfaces are commonly functionalized by the formation of thin films. Self-assembled monolayers (SAMs) are deposited on metals or metal oxides either from solution or by gas deposition. Thiols with polar terminal groups are utilized for creating the responsive surfaces which can interact electrostatically with other adsorbates. Surface charge effects wetting and adhesion, and many other surface properties. Polar terminal groups in thiols could be used to modify these factors. Mixed SAMs can provide more flexible surfaces, and could change the resulting surface properties under the influence of factors such as pH, temperature, and photo-illumination. Therefore, in order to control these phenomena by mixed polar-terminated thiols, it is necessary to understand the composition and conformation of the mixed SAMs and their response to these factors. In this work, mixtures of thiols with carboxylic and amino terminal groups were studied. Carboxylic and amino terminal groups of thiol interact with each other via hydrogen bonding in solution and form a complex. Complexes adsorb to the surface in non-conventional orientations. Unmixed SAMs from each type, either carboxylic terminated thiols or amino terminated thiols are in standing up orientation while SAMs from complexes are in an axially in-plane orientation. Selenol is an alternative to replace thiols for particular applications such as contact with biological matter which has a better compatibility with selenol than sulfur. However, the    Se-C bond is weaker than the S-C bond which limits the application of selenol. Understanding the selenol adsorption mechanism on gold surfaces could shed some light on Se-C cleavage and so is investigated in this work. Se-C cleavage happens in the low coverage areas on the step since atoms at steps have lower coordination making them more reactive than atoms on the terraces.  Another area where the self-assembly of molecules is of importance is for dye sensitized solar cells, which are based on the adsorption of the dye onto metal oxides surfaces such as TiO2.The interface between the SAM of dye and the substrate is an important factor to consider when designing dyes and surfaces in dye sensitized solar cells (DSSCs). The quality of the self-assembled monolayers of the dye on the TiO2 surface has a critical influence on the efficiency of the DSSCs.  Creation of just a monolayer of dye on the surface could lead to an efficient current of photo-excited electrons to the TiO2 and degeneration of the dye by redox. This work, T-PAC dye showed island growth with some ad-layer that is not in contact with the surface, whereas the MP13 dye adsorption is laminar growth.  Cuprite (Cu2O) is the initial and most common corrosion product for copper under atmospheric conditions. Copper could be a good replacement for noble metal as catalysts for methanol dehydrogenation. Knowledge about the structure of Cu2O(100) and Cu2O(111) surfaces could be used to obtain a deeper understanding of methanol dehydrogenation mechanisms with respect to adsorption sites on the surfaces. In this work, a detailed study was done of Cu2O(100) surface which revealed the possible surface structures as the result of different preparation conditions. Studies of the structure of Cu2O(100) and Cu2O(111) surfaces show that Cu2O(100) has a comparatively stable surface and reduces surface reactivity. As a consequence, dehydrogenation of methanol is more efficient on the Cu2O(111) surface. The hydrogen produced from methanol dehydrogenation is stored in oxygen adatom sites on both surfaces. / <p>QC 20161107</p>

Thèse numérisée par la Division de la gestion de documents et des archives de l'Université de Montréal.

Seeing beauty in the simplest aspects of nature inspires me to create art as a testament to our world. Being raised on a farm in rural Virginia gave me an appreciation of a reverence for all life. The inherent forms along with color and value establish nature as the master of aesthetics. An early introduction to Japanese art showed me that all nature was worthy and significant as subjects for art. Using materials derived from nature, cotton, linen, wool, silk, adds a tactile quality that I believe elevates the enjoyment of art.

Charles University in Prague, Faculty of Pharmacy in Hradec Králové Department of Biophysics and Physical Chemistry Candidate: Lucie Kovářová Supervisor: Ing. Vladimír Kubíček, CSc. Title of Diploma Thesis: Multicomponent analysis This diploma thesis deals with the determination of concentrations of individual dyes in mixtures by multicomponent spectrophotometric analysis. The method was tested on selected dyes which were divided into two groups. The first group contains methyl orange, methyl red, orange II and phenol red. The second group consists of methylene blue, bromocresol green and thymol blue. Within each group mixtures were prepared containing combinations of two, three and four dyes in various ratio. Spectra of prepared mixtures were measured by diode array UV/VIS spectrophotometer. Absorbance values were read at wavelengths of absorption maxima of the individual dyes. Using the pseudoinverse matrix, concentration ratios of components were calculated from the absorbance values. The determination in determined and over determined systems was performed. On the basis of the results obtained by the method of analysis it is possible to determine the individual concentration of the multi-component dyes mixtures without prior separation. Keywords: spectrophotometry, multicomponent analysis,...