<p>Direct Digital Frequency Synthesi<em>s </em>(DDFS) is a method of producing an analog waveform by</p><p>generating a time-varying signal in digital form, succeeded by digital-to-analog reconstruction.</p><p>At behavioral level the bit products with specified weights are used to generate the sine wave. In representation of a sine wave both positive and negative weights are generated. Since negative weights are not desired in design, the negative weights are transformed to positive weights. To reduce the number of current sources and control signals, bit product signals of those current sources which cannot be switched on simultaneously and have equal weights are shared. After sharing weights, the control signals are reduced to from 59 to 43 and current sources from 207 to 145.</p><p>Different control words are used by the DDFS system in order to generate different frequencies. The control word is successively added to the previous value in a 20-bit accumulator. Nine most significant bits out of these twenty bits are used for the DAC.</p><p>Since the Current Steering DAC architecture is suitable for high speed and high resolution purposes, so a 9-bit nonlinear current steering DAC is used to convert the output of bit products to the analog sine wave. Seven bits are used to generate one quarter of the sine wave. Eighth and ninth bits are used to generate the full sine wave.</p><p>HCMOS 9 (130 nm) ST Microelectronics process is used by employing high speed NMOS and PMOS transistors. The bit products (control signals) are computed by using complementary static CMOS logic which then act as control signals for the current sources after passing through D-flip flops. Practical design issues of current sources and parts of digital logic were studied and implemented using the Cadence full-custom design environment.</p>

In this thesis, a linear interpolation direct digital frequency synthesizer (DDFS) with improved structure to simplify the hardware complexity by correction block is proposed. Correction block is mainly used to compensate for the error curve of linear interpolation DDFS. From the analysis of these error curves, these error curves have similar behavior between each others. After selecting an error curve, the other error curves can be derived and multiplied by a fixed scale. From the simulation results, the correction block using the above method can improve about 12 dB spurious frequency dynamic range (SFDR). The goal of the DDFS designed in this thesis is to achieve 80 dB SFDR. Minimum required number of bits for each block in the proposed DDFS is carefully selected by simulation. In general, DDFS with piecewise linear interpolation theoretically needs 32 segments of piecewise linear interpolation to achieve 84 dB SFDR. In this thesis, 16 segments of piecewise linear interpolation with correction block can achieve the target SFDR. The chip¡¦s simulation is implemented by TSMC standard 0.13um 1P8M CMOS process with core area 78.11 x 77.49 um2.

This thesis includes two topics. The first topic is an ADFS¡]All Digital Frequency Synthesizer¡^using a Flying Adder architecture. The second one is a low-power and low-latency 2-dimensional bypassing signed multiplier. In the first topic, the ADFS is implemented by only using the standard cell library of TSMC¡]Taiwan Semiconductor Manufacturing Company¡^0.18 £gm 1P6M CMOS process. The turn-around time is effectively reduced. Furthermore, the portability and reusability of the proposed design is significantly enhanced. The design provides stable clock signals with fast switching time. In the second topic, the proposed multiplier is carried out by Baugh-Wooley algorithm using 2-dimensional bypassing units. The proposed bypassing units automatically skip redundant signal transitions when either the horizontally¡]row¡^partial products or vertically¡]column¡^operands are zero.

Direct Digital Frequency Synthesis (DDFS) is a method of producing an analog waveform by generating a time-varying signal in digital form, succeeded by digital-to-analog reconstruction. At behavioral level the bit products with specified weights are used to generate the sine wave. In representation of a sine wave both positive and negative weights are generated. Since negative weights are not desired in design, the negative weights are transformed to positive weights. To reduce the number of current sources and control signals, bit product signals of those current sources which cannot be switched on simultaneously and have equal weights are shared. After sharing weights, the control signals are reduced to from 59 to 43 and current sources from 207 to 145. Different control words are used by the DDFS system in order to generate different frequencies. The control word is successively added to the previous value in a 20-bit accumulator. Nine most significant bits out of these twenty bits are used for the DAC. Since the Current Steering DAC architecture is suitable for high speed and high resolution purposes, so a 9-bit nonlinear current steering DAC is used to convert the output of bit products to the analog sine wave. Seven bits are used to generate one quarter of the sine wave. Eighth and ninth bits are used to generate the full sine wave. HCMOS 9 (130 nm) ST Microelectronics process is used by employing high speed NMOS and PMOS transistors. The bit products (control signals) are computed by using complementary static CMOS logic which then act as control signals for the current sources after passing through D-flip flops. Practical design issues of current sources and parts of digital logic were studied and implemented using the Cadence full-custom design environment.

No description available.

Direct Digital Frequency Synthesis (DDFS) is a method of producing an analog waveform, usually a sine wave, by generating a time varying signal in digital form a then performing a digital to analog conversion. Because operations within a DDFS device are primarily digital, it can offer fast switching between output frequencies, fine frequency resolution and operation over a broad spectrum of frequencies.

This thesis deals with problematics of direct frequency digital synthesis. Principle and basic characteristics of this method of signal generating are explained in the introduction. It considers impact on purity of spectrum of output signal. Next chapter considers conception of the generator, namely choice of DDFS circuit and other basic blocks. Design of frequency multiplier, reconstruction filter and power amplifier are included. It also deals with choice of control circuit. The device is controlled by computer through USB. There was created user programme for this purpose. Measured characteristics are stated at the end of the work. This work includes schemes of connetions of designed parts including simulations and measured parameters.

Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications.