No description available.

Delta-Sigma Analog-to Digital Converters have recently become important for providing high resolution with monotonicity and reasonable signal-to-distortion ratings without the need for laser trimming techniques. This has come about because of the recent ability to combine both extensive digital computation power, and switched-capacitor analog circuitry on a monolithic chip. Delta-Sigma converters have primarily been used, however, in signal processing applications, notably digital audio, but not for instrumentation. The purpose of this dissertation is to provide a high accuracy, DC-accurate, Delta-Sigma Analog-to-Digital converter in monolithic form. Autocalibration gives endpoint correction, and chopper stabilization minimizes the effect of parameter shifts, drift, and flicker noise. A digital filter, needed for all Delta-Sigma converters, serves as a signal processor to reject out-of-band noise and resonant responses of the external system. A 3-micron, double-poly CMOS process is used. Power requirements are +/- 5 Volts. A six-pole Gaussian IIR digital filter is chosen for good transient response and no overshoot. The filter algorithm and hardware solve the difference equations of a low-pass switched-capacitor prototype filter in digital form. Due to the low bandwidth needed, an area-efficient shift-and-add architecture is used. The area is further reduced with a novel multiplication algorithm, and the logic is reused to perform the calculations required for calibration. The system level device performance is verified in FORTRAN. The analog subcircuits are simulated over process and temperature corners in HSPICE. Measurements show differential and integral linearlity, DC accuracy and noise near the 20-bit level. Power supply rejection, and out-of-band signal attenuation are good, and the step response is monotonic. The circuit is marketed as Crystal Semiconductor CSC5503 and CSC5501 (20 and 16-bit resolutions, respectively).

Tang, Xian. / Thesis (Ph.D.)--Chinese University of Hong Kong, 2013. / Includes bibliographical references. / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstract also in Chinese.

Wang Hongwei. / "February 2001." / Thesis (Ph.D.)--Chinese University of Hong Kong, 2001. / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. Ann Arbor, MI : ProQuest Information and Learning Company, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Mode of access: World Wide Web. / Abstracts in English and Chinese.

Finally, another new 0.5V fully differential wideband amplifier, which can be used in the wideband modulator, has been proposed. The gate-input two-stage amplifier employs a DC common-mode feedback circuit that uses a Miller-amplified capacitor for its frequency compensation. With the proposed technique, the power consumption of the low-voltage amplifier is drastically reduced. / Furthermore, a new dynamic CM level shifting technique for low-voltage CT delta-sigma modulators that employ a return-to-open feedback DAC is reported in the thesis. The technique maintains a stable CM level at the amplifier's inputs for this type of modulators. Simulation results show that it improves the modulator's SNDR by 11%. / In this thesis, we present research works on developing a low-voltage delta-sigma modulator with a wide signal bandwidth. Specifically, a 0.5V complex low-pass continuous-time (CT) third-order delta-sigma modulator that has a single-sided signal bandwidth of 1MHz, targeting for application in Bluetooth receivers, is presented without using any internal voltage boosting techniques which are potentially harmful to the reliability of the device. The wide bandwidth of the modulator at this low supply voltage is enabled by a special common-mode (CM) level arrangement in the system level and by new low-voltage amplifies. Realized in a 0.13mum CMOS process the proposed modulator achieves a 61.9-dB peak signal-to-noise-and-distortion ratio at the nominal supply of 0.5V with 3.4mW consumption, and occupies an active area of 0.9mm2. The modulator achieves the best figure-of-merit among its class. / The development of low-voltage design techniques for analog circuits has recently received a lot of attention due to the continuous shrinking of the supply voltage in modern CMOS technologies, which is projected to reduce to 0.5V for low power applications within ten years in the International Technology Roadmap for Semiconductor. This thesis focuses on developing circuit techniques for low-voltage delta-sigma modulator, a functional block that is widely used in mixed-signal integrated circuits. Several delta-sigma modulators operating at supply voltages below 0.9V have been reported in the open literature. However, none of them supports a signal bandwidth wider than 100kHz with a reasonable performance. / He, Xiaoyong. / Adviser: Kong Pang Pun. / Source: Dissertation Abstracts International, Volume: 72-01, Section: B, page: . / Thesis (Ph.D.)--Chinese University of Hong Kong, 2010. / Includes bibliographical references (leaves 104-111). / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. Ann Arbor, MI : ProQuest Information and Learning Company, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. Ann Arbor, MI : ProQuest Information and Learning Company, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstract also in Chinese.

Ko, Chi Tung. / On t.p. "delta" and "sigma" appear as the Greek letters. / Thesis submitted in: December 2007. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2008. / Includes bibliographical references. / Abstracts in English and Chinese. / Abstract --- p.1 / 摘要 --- p.3 / Acknowledgements --- p.4 / Table of Contents --- p.5 / List of Figures --- p.8 / List of Tables --- p.13 / Chapter Chapter 1 --- Introduction --- p.14 / Chapter 1.1 --- Motivation --- p.14 / Chapter 1.2 --- Objectives --- p.17 / Chapter 1.3 --- Organization of the Thesis --- p.17 / References --- p.18 / Chapter Chapter 2 --- Fundamentals of Delta-sigma Modulators --- p.20 / Chapter 2.1 --- Delta-sigma Modulator as a Feedback System --- p.20 / Chapter 2.2 --- Quantization Noise --- p.22 / Chapter 2.3 --- Oversampling --- p.23 / Chapter 2.4 --- Noise Shaping --- p.25 / Chapter 2.5 --- Performance Parameters --- p.27 / Chapter 2.6 --- Baseband Modulators vs Bandpass Modulators --- p.27 / Chapter 2.7 --- Discrete-time Modulators vs Continuous-time Modulators --- p.28 / Chapter 2.8 --- Single-bit Modulators vs Multi-bit Modulators --- p.29 / Chapter 2.9 --- Non-linearity and Image Problems in Multi-bit Delta-sigma Modulators --- p.29 / Chapter 2.9.1 --- Non-linearity Problem --- p.29 / Chapter 2.9.2 --- Image Problem --- p.31 / Reference --- p.36 / Chapter Chapter 3 --- Image Rejection and Non-linearity Suppression Techniques for Quadrature Multi-bit Δ¡♭ Modulators --- p.38 / Chapter 3.1 --- Quadrature DEM Technique --- p.38 / Chapter 3.1.1 --- Introduction and Working Principle --- p.38 / Chapter 3.1.2 --- Behavioral Simulation Results --- p.42 / Chapter 3.2 --- IQ DWA Technique --- p.44 / Chapter 3.2.1 --- Introduction and Working Principle --- p.44 / Chapter 3.2.2 --- Behavioral Simulation Results --- p.49 / Chapter 3.3 --- DWA and Bit-wise Data-Dependent DEM --- p.52 / Chapter 3.3.1 --- Introduction and Working Principle --- p.52 / Chapter 3.3.2 --- Behavioral Simulation Results --- p.54 / Chapter 3.4 --- Image Rejection Technique for Quadrature Mixer --- p.61 / Chapter 3.5 --- Conclusion --- p.63 / Reference --- p.64 / Chapter Chapter 4 --- System Design of a Multi-Bit CT Modulator for GSM/WCDMA Application --- p.65 / Chapter 4.1 --- Objective of Design and Design Specification --- p.65 / Chapter 4.2 --- Topology Selection --- p.65 / Chapter 4.3 --- Discrete-time Noise Transfer Function Generation --- p.66 / Chapter 4.4 --- Continuous-time Loop Filter Transfer Function Generation --- p.69 / Chapter 4.5 --- Behavioral Model of Modulator --- p.69 / Chapter 4.6 --- Dynamic Range Scaling --- p.75 / Chapter 4.7 --- Behavioral Modeling of Operational Amplifiers --- p.77 / Chapter 4.8 --- Impact of RC Variation on Performance --- p.85 / Chapter 4.9 --- Loop Filter Component Values --- p.88 / Chapter 4.10 --- Summary --- p.90 / Reference --- p.90 / Chapter Chapter 5 --- Transistor-level Implementation of Modulators --- p.92 / Chapter 5.1 --- Overview of Design --- p.92 / Chapter 5.2 --- Design of Operational Transconductance Amplifiers (OTAs) --- p.94 / Chapter 5.2.1 --- First Stage --- p.94 / Chapter 5.2.2 --- Second and Third Stages --- p.98 / Chapter 5.3 --- Design of Feed-forward Transconductance (Gm) Cells --- p.101 / Chapter 5.4 --- Design of Quantizer --- p.102 / Chapter 5.4.1 --- Reference Ladder Design --- p.102 / Chapter 5.4.2 --- Comparator Design --- p.104 / Chapter 5.5 --- Design of Feedback Digital-to-Analog Converter (DAC) --- p.106 / Chapter 5.5.1 --- DWA and DEM Logic --- p.107 / Chapter 5.5.2 --- DAC Circuit --- p.109 / Chapter 5.6 --- Design of Integrated Mixers --- p.111 / Chapter 5.7 --- Design of Clock Generators --- p.112 / Chapter 5.7.1 --- Master Clock Generator --- p.112 / Chapter 5.7.2 --- LO Clock Generator --- p.114 / Chapter 5.7.3 --- Simulation Results --- p.116 / Reference --- p.125 / Chapter Chapter 6 --- Physical Design of Modulators --- p.127 / Chapter 6.1 --- Floor Planning of Modulator --- p.127 / Chapter 6.2 --- Shielding of Sensitive Signals --- p.130 / Chapter 6.3 --- Common Centroid Layout --- p.130 / Chapter 6.4 --- Amplifier Layout --- p.132 / Reference --- p.137 / Chapter Chapter 7 --- Conclusions --- p.138 / Chapter 7.1 --- Conclusions --- p.138 / Chapter 7.2 --- Future Works --- p.138 / Appendix A Schematics of Building Blocks --- p.140 / First Stage Operational Amplifier --- p.140 / First Stage Amplifier Local Bias Circuit --- p.140 / Second and Third Stage Operational Amplifier --- p.141 / Second and Third Stage Local Bias Circuit --- p.141 / CMFB Circuit (First Stage) --- p.142 / CMFB Circuit (Second Stage) --- p.142 / Gm-Feed-forward Cells --- p.143 / Gm Feed-forward Cell Bias Circuit --- p.143 / Reference Ladder Circuit --- p.144 / Pre-amplifier Circuit --- p.145 / Latch Circuit --- p.145 / DAC Circuit (Unit Cell) --- p.146 / Author's Publications --- p.147

In this thesis work, a design of 14-bit, 20MS/s segmented digital-to-analog converter (DAC) is presented. The segmented DAC uses switched-capacitor configuration to implement 8 (LSB) + 6 (MSB) segmented architecture to achieve high performance for minimum area. The implemented LSB DAC is based on quasi-passive pipelined DAC that has been proven to provide low power and high speed operation. Typically, capacitor matching is the best among all integrated circuit components but the mismatch among nominally equal value capacitors will introduce nonlinear distortion. By using dynamic element matching (DEM) technique in the MSB DAC, the nonlinearity caused by capacitor mismatch is greatly reduced. The output buffer employed direct charge transfer (DCT) technique that can minimize kT/C noise without increasing the power dissipation. This segmented DAC is designed and simulated in 0.18 μm CMOS technology, and the simulated core DAC block only consumes 403 μW. / Graduation date: 2012

Graduation date: 1996