Environmentally friendly renewable energy technologies such as wind and solar energy systems are among the fleet of new generating technologies driving the demand for distributed generation of electricity. Power Electronics has initiated the next tech¬nological revolution and enables the connection of distributed generation (DG) systems to the grid. The challenge is to achieve system functionality without extensive custom engineering, yet still have high system reliability and generation placement flexibility. Nowadays, it is a general trend to increase the electricity production using DG systems. If these systems are not properly controlled, their connection to the utility network can generate problems on the grid side. Therefore, considerations about power generation, safe running and grid synchronization must be done before connecting these systems to the utility network. This thesis introduces a new grid-synchronization, or more visibly a new “power signal processor” adaptive notch filtering (ANF) tool that can potentially stimulate much interest in the field and provide improvement solutions for grid-connected operation of DG systems. The processor is simple and offers high degree of immunity and insensitivity to power system disturbances, harmonics and other types of pollutions that exist in the grid signal. The processor is capable of decomposing three-phase quantities into symmetrical components, extracting harmonics, tracking the frequency variations, and providing means for voltage regulation and reactive power control. In addition, this simple and powerful synchronization tool will simplify the control issues currently challenging the integration of distributed energy technologies onto the electricity grid. All converter-interfaced equipments like FACTS (flexible ac transmission systems) and Custom Power Controllers will benefit from this technique. The theoretical analysis is presented, and simulation and experimental results confirm the validity of the analytical work. / Thesis (Ph.D, Electrical & Computer Engineering) -- Queen's University, 2009-01-27 11:37:07.279

A utilização de conversores multiníveis tem sido uma importante alternativa para aplicações de alta potência e média tensão, graças aos altos níveis de potência alcançáveis por estas estruturas. Recentemente, esta topologia de conversores foi aplicada em sistemas com fontes alternativas para alimentar um sistema de geração distribuída, nos quais diferentes fontes de energia eram utilizadas. Com base nas características dos conversores multinível e sua potencial aplicabilidade em sistemas de geração distribuída, este trabalho tem como objetivo construir um sistema multinível conectado a rede de distribuição para utilização de fontes alternativas de energia como fontes primárias. Considerando que a energia fornecida pelas fontes alternativas pode sofrer variações, propõe-se a integração de sistemas armazenadores de energia, como capacitores, ao sistema multinível. Por isso, este trabalho desenvolve uma estratégia de controle para máxima transferência de potência ativa entregue à rede a fim de obter um fluxo ótimo. A topologia multinível deste trabalho possui em sua configuração dois módulos inversores conectados em série. Neste caso, é possível que pelo menos um desses inversores funcione com uma modulação em baixa frequência processando a maior parcela de potência. Assim, duas estratégias de controle modulação de fase e modulação de amplitude para a transferência de potência realizada pelo inversor de baixa frequência são analisadas. As vantagens e desvantagens de cada um dos métodos são expostas e então a estratégia mais adequada, no caso a modulação de amplitude, é utilizada na operação do conversor multinível. Além disso, são apresentados a modelagem das plantas e o projeto dos controladores de cada um dos módulos inversores. Por fim, a validação da proposta é feita através dos resultados de simulações e experimentais que mostram a capacidade do sistema de geração em transferir potência constante para a rede de distribuição e manter a corrente quase sem distorções em fase com a tensão. / The utilization of multilevel converters has been an important alternative for medium voltage applications with high power and power quality demand, thanks to the high power levels achievable for this kind of structure. Recently, this converter topology was proposed as a new possibility in renewable energy source applications, mainly in system delivering power to the grid, where different renewable energy resources may be used. Based on the characteristics of multilevel converters, and their potential applicability in distributed generation systems, this study aims to build a multilevel system that could be powered by renewable energy sources as primary sources and then connect them to a distribution grid. However, considering the energy produced by alternative sources can vary, it is analyzed the integration of a storage energy system in this multilevel topology. Taking into account this ends, the main concern of this study is related to the development of a control strategy to maximize the active power transferred to the grid. The multilevel topology employed in this study has two H-bridge inverter modules connected in series forming a cascaded configuration. Therefore, it is possible that at least one of these inverters, operating with a low frequency of modulation, process the majority of power with lower amount of losses. On this way, two control strategies for power transfer are analyzed. The advantages and disadvantages of each method are presented, and the most appropriated strategy is used in the operation of the multilevel converter system. In addition, it has been presented the design criteria for each controller and finally the validation of the proposed approach is done by mains of simulations and experimental results which show the ability of the converter to transfer constant active power to the grid and keep the grid current in phase with the grid voltage.

A utilização de conversores multiníveis tem sido uma importante alternativa para aplicações de alta potência e média tensão, graças aos altos níveis de potência alcançáveis por estas estruturas. Recentemente, esta topologia de conversores foi aplicada em sistemas com fontes alternativas para alimentar um sistema de geração distribuída, nos quais diferentes fontes de energia eram utilizadas. Com base nas características dos conversores multinível e sua potencial aplicabilidade em sistemas de geração distribuída, este trabalho tem como objetivo construir um sistema multinível conectado a rede de distribuição para utilização de fontes alternativas de energia como fontes primárias. Considerando que a energia fornecida pelas fontes alternativas pode sofrer variações, propõe-se a integração de sistemas armazenadores de energia, como capacitores, ao sistema multinível. Por isso, este trabalho desenvolve uma estratégia de controle para máxima transferência de potência ativa entregue à rede a fim de obter um fluxo ótimo. A topologia multinível deste trabalho possui em sua configuração dois módulos inversores conectados em série. Neste caso, é possível que pelo menos um desses inversores funcione com uma modulação em baixa frequência processando a maior parcela de potência. Assim, duas estratégias de controle modulação de fase e modulação de amplitude para a transferência de potência realizada pelo inversor de baixa frequência são analisadas. As vantagens e desvantagens de cada um dos métodos são expostas e então a estratégia mais adequada, no caso a modulação de amplitude, é utilizada na operação do conversor multinível. Além disso, são apresentados a modelagem das plantas e o projeto dos controladores de cada um dos módulos inversores. Por fim, a validação da proposta é feita através dos resultados de simulações e experimentais que mostram a capacidade do sistema de geração em transferir potência constante para a rede de distribuição e manter a corrente quase sem distorções em fase com a tensão. / The utilization of multilevel converters has been an important alternative for medium voltage applications with high power and power quality demand, thanks to the high power levels achievable for this kind of structure. Recently, this converter topology was proposed as a new possibility in renewable energy source applications, mainly in system delivering power to the grid, where different renewable energy resources may be used. Based on the characteristics of multilevel converters, and their potential applicability in distributed generation systems, this study aims to build a multilevel system that could be powered by renewable energy sources as primary sources and then connect them to a distribution grid. However, considering the energy produced by alternative sources can vary, it is analyzed the integration of a storage energy system in this multilevel topology. Taking into account this ends, the main concern of this study is related to the development of a control strategy to maximize the active power transferred to the grid. The multilevel topology employed in this study has two H-bridge inverter modules connected in series forming a cascaded configuration. Therefore, it is possible that at least one of these inverters, operating with a low frequency of modulation, process the majority of power with lower amount of losses. On this way, two control strategies for power transfer are analyzed. The advantages and disadvantages of each method are presented, and the most appropriated strategy is used in the operation of the multilevel converter system. In addition, it has been presented the design criteria for each controller and finally the validation of the proposed approach is done by mains of simulations and experimental results which show the ability of the converter to transfer constant active power to the grid and keep the grid current in phase with the grid voltage.

No description available.

Continued increase in system load leading to a reduction in operating margins, as well as the tendency to move towards a deregulated grid with renewable energy sources has increased the vulnerability of the grid to blackouts. Advanced intelligent techniques are therefore required to design new monitoring schemes that enable smart grid operation in a secure and robust manner. As the grid is highly interconnected, monitoring of transmission and distribution systems is increasingly relying on digital communication. Conventional security assessment techniques are slow, hampering real-time decision making. Hence, there is a need to develop fast and accurate security monitoring techniques. Intelligent techniques that are capable of processing large amounts of captured data are finding increasing scope as essential enablers for the smart grid. The research work presented in this thesis has evolved from the need for enhanced monitoring in transmission and distribution grids. The potential of intelligent techniques for enhanced system monitoring has been demonstrated for disturbed scenarios in an integrated power system. In transmission grids, one of the challenging problems is network partitioning, also known as network area-decomposition. In this thesis, an approach based on relative electrical distance (RED) has been devised to construct zonal dynamic equivalents such that the dynamic characteristics of the original system are retained in the equivalent system within the desired accuracy. Identification of coherent generators is another key aspect in power system dynamics. In this thesis, a support vector clustering-based coherency identification technique is proposed for large interconnected multi-machine power systems. The clustering technique is based on coherency measure which is formulated using the generator rotor measurements. These rotor measurements can be obtained with the help of Phasor Measurement Units (PMUs). In distribution grids, accurate and fast fault identification of faults is a key challenge. Hence, an automated fault diagnosis technique based on multi class support vector machines (SVMs) has been developed in this thesis. The proposed fault location scheme is capable of accurately identify the fault type, location of faulted line section and the fault impedance in the distributed generation (DG) systems. The proposed approach is based on the three phase voltage and current measurements available at all the sources i.e. substation and at the connection points of DGs. An approach for voltage instability monitoring in 3-phase distribution systems has also been proposed in this thesis. The conventional single phase L-index measure has been extended to a 3-phase system to incorporate information pertaining to unbalance in the distribution system. All the approaches proposed in this thesis have been validated using standard IEEE test systems and also on practical Indian systems.

Over the last decade, power systems have evolved dramatically around the world, owing to higher demand, stringent requirements on quality and environmental concerns that are becoming increasingly critical. With the introduction of new technologies like large-scale renewable energy, wide-area measurement based on phasor measurement units (PMUs) and consumer interaction in the distribution system, the power grid today has become more potent than ever before. Most of the defining features of the smart grid today rest on the integration of advanced communication capabilities into the grid. While communication infrastructure has become a key enabler for the smart grid, it also introduces new and complex control challenges that must be addressed. As we increasingly rely on information transmitted to distant areas over communication networks, it becomes imperative to model the effects of the communication system on the stability of the power grid. Several approaches exist in control theory to study such systems, widely referred to as Networked Control Systems (NCS). Networked control theory provides mathematical tools for system stability analysis and control in the presence of communication delays, packet dropouts and disordering due to transmission of sensor and actuator signals via a limited communication network. In this thesis, a networked control framework for smart grids with integrated commu-nication infrastructure (ICT) is developed. In particular, a networked control systems perspective is developed for two scenarios - wide-area monitoring control, and coordinated control of distributed generation sources. The effects of communication delays and packet dropouts on power system stability are modeled in detail. In the wide-area monitoring control problem, system state measurements are trans-mitted from remote locations through a communication network. The system is modeled as an NCS and a control design approach is presented to damp inter-area oscillations arising from various power system disturbances in the presence of communication constraints. In the coordinated control scenario, a power system with geographically dispersed sources is modeled as an NCS. A networked controller is designed to stabilize the system in the presence of small signal disturbances when system measurements are subject to communication delays and packet dropouts. A realistic output feedback networked control scheme that only uses voltage measurements from PMUs is also developed for practical implementation. The networked controllers designed in this thesis are validated against controllers designed by standard methods, by simulation on standard test systems. The networked controllers are found to enhance power system stability and load transfer capability even in the presence of severe packet dropouts and delays. Several extensions and theoretical problems motivated by this thesis are also proposed.