Emerging wireless standards are designed to be spectrally efficient to address the high cost of licensing wireless spectra. Unfortunately, the resulting signals have a high peak-to-average ratio that reduces the base station power amplifier efficiency at the back-off power level. The wasted energy is converted to heat that degrades the device reliability and increases the base-station’s carbon footprint and cooling requirements. In addition, these new standards place stringent re- quirements on the amplifier output power, linearity, efficiency, and bandwidth. To improve the back-off efficiency, a Doherty amplifier, which uses two device in parallel for back-off efficiency enhancement, is deployed in a typical base station. Unfortunately, the conventional Doherty amplifier is narrowband and thus cannot satisfy the bandwidth requirement of the modern base station that needs to support multiple standards and backward compatibility. In this thesis, we begin by studying the class F/F−1 high efficiency mode of operation. To this end, we designed a narrowband, harmonically-tuned 3.3 GHz, 10 W GaN high efficiency amplifier. Next, we investigate how to simultaneously achieve high efficiency and broad bandwidth by harnessing the simplified real frequency technique for the broadband matching network design. A 2 to 3 GHz, 45 W GaN amplifier and a 650 to 1050 MHz, 45 W LDMOS amplifier were designed. Finally, we analyze the conventional Doherty amplifier to determine the cause of its narrow bandwidth. We find that the narrow bandwidth can be attributed to the band-limited quarter-wave transformer as well as the widely adopted traditional design technique. As an original contribution to knowledge, we propose a novel Doherty amplifier configuration with intrinsically broadband characteristics by analyzing the load modulation concept and the conventional Doherty amplifier. The proposed amplifier uses asymmetrical drain voltage biases and symmetrical devices and it does not require a complex mixed-signal setup. To demonstrate the proposed concept in practice, we designed a 700 to 1000 MHz, 90 W GaN broadband Doherty amplifier. Moreover, to show that the proposed concept is applicable to high power designs, we designed a 200 W GaN broadband Doherty amplifier in the same band. In addition, to show that the technique is independent of the device technology, we designed a 700 to 900 MHz, 60 W LDMOS broadband Doherty amplifier. Using digital pre-distortion, the three prototypes were shown to be highly linearizable when driven with wideband 20 MHz LTE and WCDMA modulated signals and achieved excellent back-off efficiency. Lastly, using the insights from the previous analyses, we propose a novel mixed-technology Doherty amplifier with an extended and reconfigurable back-off level as well as an improved power utilization factor. The reconfigurability of the proposed amplifier makes it possible to customize the back-off level to achieve the highest average efficiency for a given modulated signal without redesigning the matching networks. A 790 to 960 MHz, 180 W LDMOS/GaN Doherty amplifier demonstrated the extended bandwidth and reconfigurability of the back-off level. The proposed amplifier addresses the shortcomings of the conventional Doherty amplifier and satisfies the many requirements of a modern base station power amplifier.

Emerging wireless standards are designed to be spectrally efficient to address the high cost of licensing wireless spectra. Unfortunately, the resulting signals have a high peak-to-average ratio that reduces the base station power amplifier efficiency at the back-off power level. The wasted energy is converted to heat that degrades the device reliability and increases the base-station’s carbon footprint and cooling requirements. In addition, these new standards place stringent re- quirements on the amplifier output power, linearity, efficiency, and bandwidth. To improve the back-off efficiency, a Doherty amplifier, which uses two device in parallel for back-off efficiency enhancement, is deployed in a typical base station. Unfortunately, the conventional Doherty amplifier is narrowband and thus cannot satisfy the bandwidth requirement of the modern base station that needs to support multiple standards and backward compatibility. In this thesis, we begin by studying the class F/F−1 high efficiency mode of operation. To this end, we designed a narrowband, harmonically-tuned 3.3 GHz, 10 W GaN high efficiency amplifier. Next, we investigate how to simultaneously achieve high efficiency and broad bandwidth by harnessing the simplified real frequency technique for the broadband matching network design. A 2 to 3 GHz, 45 W GaN amplifier and a 650 to 1050 MHz, 45 W LDMOS amplifier were designed. Finally, we analyze the conventional Doherty amplifier to determine the cause of its narrow bandwidth. We find that the narrow bandwidth can be attributed to the band-limited quarter-wave transformer as well as the widely adopted traditional design technique. As an original contribution to knowledge, we propose a novel Doherty amplifier configuration with intrinsically broadband characteristics by analyzing the load modulation concept and the conventional Doherty amplifier. The proposed amplifier uses asymmetrical drain voltage biases and symmetrical devices and it does not require a complex mixed-signal setup. To demonstrate the proposed concept in practice, we designed a 700 to 1000 MHz, 90 W GaN broadband Doherty amplifier. Moreover, to show that the proposed concept is applicable to high power designs, we designed a 200 W GaN broadband Doherty amplifier in the same band. In addition, to show that the technique is independent of the device technology, we designed a 700 to 900 MHz, 60 W LDMOS broadband Doherty amplifier. Using digital pre-distortion, the three prototypes were shown to be highly linearizable when driven with wideband 20 MHz LTE and WCDMA modulated signals and achieved excellent back-off efficiency. Lastly, using the insights from the previous analyses, we propose a novel mixed-technology Doherty amplifier with an extended and reconfigurable back-off level as well as an improved power utilization factor. The reconfigurability of the proposed amplifier makes it possible to customize the back-off level to achieve the highest average efficiency for a given modulated signal without redesigning the matching networks. A 790 to 960 MHz, 180 W LDMOS/GaN Doherty amplifier demonstrated the extended bandwidth and reconfigurability of the back-off level. The proposed amplifier addresses the shortcomings of the conventional Doherty amplifier and satisfies the many requirements of a modern base station power amplifier.

In this thesis, novel designs for adaptive power amplifiers, capable of maintaining excellent performance at dissimilar signal parameters, are presented. These designs result in electronically reconfigurable, single-ended and Doherty power amplifiers (DPA) that efficiently sustain functionality at different driving signal levels, highly varying time domain characteristics and wide-spread frequency bands. The foregoing three contexts represent those dictated by the diverse standards of modern communication systems. Firstly, two prototypes for a harmonically-tuned reconfigurable matching network using discrete radio frequency (RF) microelectromechanical systems (MEMS) switches and semiconductor varactors will be introduced. Following that is an explanation of how the varactor-based matching network was used to develop a high performance reconfigurable Class F-1 power amplifier. Afterwards, a systematic design procedure for realizing an electronically reconfigurable DPA capable of operating at arbitrary centre frequencies, average power levels and back-off efficiency enhancement power ranges is presented. Complete sets of closed-form equations are outlined which were used to build tunable matching networks that compensate for the deviation of the Doherty distributed elements under the desired deployment scenarios. Off-the-shelf RF MEMS switches are used to realize the reconfigurability of the adaptive Doherty amplifiers. Finally, based on the derived closed-form equations, a tri-band, monolithically integrated DPA was realized using the Canadian Photonics Fabrication Centre (CPFC??) GaN500 monolithic microwave integrated circuit (MMIC) process. Successful integration of high power, high performance RF MEMS switches within the MMIC process paved the way for the realization of the frequency-agile, integrated version of the adaptive Doherty amplifier.

Next generation mobile communication systems require the use of linear RF power amplifier for higher data transmission rates. However, linear RF power amplifiers are inherently inefficient and usually require additional circuits or further system adjustments for better efficiency. This dissertation focuses on the development of new efficiency enhancement schemes for linear RF power amplifiers. The multistage Doherty amplifier technique is proposed to improve the performance of linear RF power amplifiers operated in a low power level. This technique advances the original Doherty amplifier scheme by improving the efficiency at much lower power level. The proposed technique is supported by a new approach in device periphery calculation to reduce AM/AM distortion and a further improvement of linearity by the bias adaptation concept. The device periphery adjustment technique for efficiency enhancement of power amplifier integrated circuits is also proposed in this work. The concept is clearly explained together with its implementation on CMOS and SiGe RF power amplifier designs. Furthermore, linearity improvement technique using the cancellation of nonlinear terms is proposed for the CMOS power amplifier in combination with the efficiency enhancement technique. In addition to the efficiency enhancement of power amplifiers, a scalable large-signal MOSFET model using the modified BSIM3v3 approach is proposed. A new scalable substrate network model is developed to enhance the accuracy of the BSIM3v3 model in RF and microwave applications. The proposed model simplifies the modeling of substrate coupling effects in MOS transistor and provides great accuracy in both small-signal and large-signal performances.