Thesis (MScEng)-- Stellenbosch University, 2013. / ENGLISH ABSTRACT: The objective of this research was to obtain clean drinkable water from treated sewage effluent by using a solar-powered distillation cycle. Technologies and concepts were borrowed from the solar desalination industry to propose a unique circular distillation cell design. From the design, a specific mathematical correlation was developed to predict the distillate mass flow rate by using only evaporation and condensation temperature as inputs. This model was incorporated into a simulation model built using Transient System Simulation software. Long-term simulations were carried out to determine the operating capabilities of the design. A prototype was successfully constructed and operated. Experimental results indicated good agreement with the mass flow rate mathematical correlation. Water quality levels were tested against the South African National Standard 241 national drinking water quality standard. Four quality parameters are outside acceptable levels. Evidence suggested that acceptable quality levels could be reached. The circular distillation cell design is a major contribution made by this research. Another contribution is the simulation model capable of predicting an output for different locations. Finally, the proposed prototype is potentially a very valuable device contributing towards the reduction of consumer demand in terms of water and energy as well as the household load on the wastewater treatment system. / AFRIKAANSE OPSOMMING: Die doel van hierdie tesis is om te beskryf hoe behandelde rioolwater deur middel van ’n son aangedrewe distillasiesisteem gesuiwer kan word om drinkbare water as eindproduk te lewer. Die nodige tegnologieë en konsepte is oorgeneem uit kommersiële sonaangedrewe ontsoutingsisteme om met ’n unieke ontwerp voorendag te kom wat uit ’n sirkelvormige natuurlike konveksie distillasiesel bestaan. Met behulp van hierdie ontwerp is ’n wiskundige korrelasie ontwikkel om die gesuiwerde water se massavloei te bepaal. Slegs die verdampings- en kondensasietemperature word as insetwaardes gebruik om die massavloei te bereken. ’n Simulasiemodel is met behulp van die Transient System Simulation programmatuur gebou. Die wiskundige korrelasie is by die simulasiemodel geïnkorporeer om langtermynsimulasies te kan uitvoer. Voorts is ’n demonstrasiemodel suksesvol gebou en aangedryf. Eksperimentele resultate toon goeie ooreenstemming met die simulasieresultate. Die gesuiwerde water se gehalte is met die nationale SANS 241 drinkwaterstandaard as maatstaf getoets. Slegs vier gehalteparameters val buite die aanvaarbare vlakke, hoewel dit blyk dat hierdie elemente wel tot aanvaarbare vlakke verlaag kan word. Hierdie navorsing se grootstet bydrae is die ontwerp van die unieke sirkelvormige distillasiesel. ’n Bykomende bydra is die aanpasbaarheid van die simulasiemodel sodat dit produksievermoë op verskillende plekke kan voorspel. Die demonstrasiemodel is ’n potensieel waardevolle ontwerp wat kan bydra tot die verlaging in verbruikersaanvraag na water en energie. ’n Ontwerp van hierdie aard kan die las wat huishoudings op suiweringaanlegte vir rioolwater plaas, verlig.

Disinfection by-products (DBPs) are a major group of water contaminants and their role in causing adverse health outcomes, including adverse pregnancy outcomes, endocrine disruption, respiratory related adverse health outcomes and cancer has been subject to extensive epidemiological and toxicological research and review. Determination of safe exposure to DBPs, particularly within drinking water supplies, has been a topic of extensive debate, with a wide range of acceptable levels set across the industrialized world. The focus of the research in this thesis was on two of the main health outcomes associated with DBP exposure, namely adverse pregnancy outcomes and asthma related symptoms. To assess adverse pregnancy outcomes in Perth, an extensive classification quantification of the major DBPs in Perth drinking water was conducted. A registrybased prevalence study was carried out to assess birth defects in relation to high, medium and low DBP areas (defined by the water sampling and analysis). It was found that women living in high THM areas are 22% (odds ratio (OR) 1.22, 95% confidence interval (95% CI) 1.01-1.48) more likely of having a baby with any birth defect. High exposure was also strongly associated with an increased risk of having a baby with a cardiovascular defect (62% increased risk). Low birth weight and prematurity were also assessed; however these outcomes were not associated with an increased risk through an increase in exposure. Following on from this analysis, a population risk assessment model was developed for DBPs in high exposure environments. This involved a three step process: (i) Firstly a questionnaire-based validation and reliability study was used to assess water consumption patterns of a population of pregnant women in Perth. (ii) Secondly a prediction model for teratogenic burden of DBPs in Perth was developed, related to the exposure patterns of the population of pregnant women involved in the validation and reliability study. (iii) Finally, combining the information collected in (i) and (ii), along with the regression slope estimates for birth weight from the prevalence study (defined in Section 2.2.1), a dose-response model for THMs and birth weight was developed. Predictive simulations for birth weights at given THM levels were then conducted. It was estimated that pregnant women in Perth are exposed to between 0.3 – 4.10 µg/day ingested TTHM, and of this, the more toxic brominated forms accounted for between 0.27 – 3.69 µg/day. Based on a dose-response model used, birthweights calculated for the ‘hypothetical’ exposures ranged from 3403.2g for the highest exposure to 3503.5g in the lowest exposure, which is a difference of over 100g. Although the resulting reduction in birth weight is not extreme, there is still a significant reduction in birth weight present as exposure to TTHMs increases. This is the first doseresponse model to be developed to assess an adverse pregnancy outcome based on pregnant women exposure data, and will be a useful tool for assessing varying exposures throughout not only Australia but also throughout the industrialised world, where DBP exposure is highly prevalent.

Graduation date: 2003 / Best scan available on figures. Original figures are dark.

The removal of microbial populations from potable water has been a practice with great importance towards public health, as it has resulted in the reduction of literally millions of cases of infectious disease. In the United States, pathogenic organisms are most commonly removed from drinking water through the application of chlorine. Ninety-nine per cent of all U.S. potable water treatment facilities that disinfect, rely on chlorine as their sole or primary disinfectant, and over 175,000,000 Americans regularly consume chlorinated water. In 1974, Rook and Bellar et al. published studies which indicated that chlorine reacted with organic matter in water during treatment to produce a wide-range of halogenated by-products. Since that time, numerous analyses have been performed to isolate and identify the by-products of chlorination. Toxicologic and epidemiologic studies have been performed, some of which suggest that the use of chlorine as a disinfectant may be contributing to the incidence of chronic disease in the United States. Because of the concern that the use of chlorine for potable water disinfection may be contributing to chronic disease, Amendments to the Safe Drinking Water Act (SDWA) have been promulgated which strictly regulate disinfectants and disinfection by-products. Future disinfectant and disinfectant by-product regulations (1992) will have a major impact on the purveyors of potable water in the U.S.. Probably the largest challenge U.S. water treatment utilities now face is in the attempt to control for disinfectants and disinfectant by-products while maintaining the microbiological integrity of the water supply. The SDWA Amendments and their supporting regulations will result in major changes in the way water quality parameters are measured, and the way disinfection and treatment strategies are practiced. This thesis looks closely at the role of chlorine as a disinfectant, the by-products arising from chlorine reacting with organic matter, as well as the rationale behind the disinfectant and disinfectant by-product regulations. After examining the chemical, toxicologic and epidemiologic evidence which fueled the new SDWA regulations, available treatment strategies for meeting the new regulations will be detailed and examined. A water treatment strategy which best appears to maximize the reduction of waterborne disease and minimize the risk of chronic disease will then be offered. / Graduation date: 1992

Water, sanitation and hygiene-related diseases are responsible for 7% of all deaths and 8% of all disability adjusted live years (DALYs), as well as the loss of 320 million days of productivity in developing countries. Though laboratory and field trials have shown that household water treatment (HWT) technologies can quickly improve the microbiological quality of drinking water, questions remain about the effectiveness of these technologies under real-world conditions. Furthermore, the value that rural communities attach to HWT is unknown, and it is not clear why, in spite of the fact that rural African households need household water treatment (HWT) most, they are the least likely to use them. The primary objective of this multi-level study was to assess the post-implementation effectiveness of selected HWT technologies in the Nyanza and Western Provinces of Kenya. The study was carried out in the rainy season between March and May, 2011 using a mixed method approach. Evidence was collected in order to build a case of evidence of HWT effectiveness or ineffectiveness in a post-implementation context. A quasi-experimental design was used first to conduct a Knowledge, Attitudes and Practices (KAP) survey in 474 households in ten intervention and five control villages (Chapter 3). The survey assessed the context in which household water treatment was being used in the study villages to provide real-world information for assessing the effectiveness of the technologies. An interviewer-administered questionnaire elicited information about the water, sanitation and hygiene-related KAP of the study communities. A household water treatment (HWT) survey (Chapter 4) was carried out in the same study households and villages as the KAP study, using a semi-structured questionnaire to gather HWT adoption, compliance and sustained use-related information to provide insight into the perceived value the study households attach to HWT technologies, and their likelihood of adoption of and compliance with these technologies. The drinking water quality of 171 (one quarter of those surveyed during KAP) randomly selected households was determined and tracked from source to the point of use (Chapter 5). This provided insights into HWT effectiveness by highlighting the need for HWT (as indicated by source water quality) and the effect of the study households’ KAP on drinking water quality (as indicated by the stored water quality). Physico-chemical and microbiological water quality of the nineteen improved and unimproved sources used by the study households was determined, according to the World Health Organisation guidelines. The microbiological quality of 291 water samples in six intervention and five control villages was determined from source to the point-of-use (POU) using the WHO and Sphere Drinking Water Quality Guidelines. An observational study design was then used to assess the post-implementation effectiveness of the technologies used in 37 households in five intervention villages (Chapter 6). Three assessments were carried out to determine the changes in the microbiological quality of 107 drinking water samples before treatment (from collection container) and after treatment (from storage container) by the households. The criteria used to assess the performance of the technologies were microbial efficacy, robustness and performance in relation to sector standards. A Quantitative Microbial Risk Assessment (QMRA) was then carried out in the HWT effectiveness study households to assess the technologies’ ability to reduce the users’ exposure to and probability of infection with water-borne pathogens (Chapter 7). The KAP survey showed that the intervention and control communities did not differ significantly in 18 out of 20 socio-economic variables that could potentially be influenced by the structured manner of introducing HWT into the intervention villages. The majority of the intervention group (IG) and the control group (CG) were poor or very poor on the basis of household assets they owned. The predominant level of education for almost two-thirds of the IG and CG respondents was primary school (completed and non-completed). Though very few were unemployed in IG (8.07%) and CG (14.29%), the two groups of respondents were predominantly engaged in subsistence farming — a low income occupation. With regard to practices, both groups had inadequate access to water and sanitation with only one in two of the households in both IG and CG using improved water sources as their main drinking water source in the non-rainy season. One in ten households in both study groups possessed an improved sanitation facility, though the CG was significantly more likely to practice open defecation than the IG. The self-reported use of soap in both study groups was mainly for bathing and not for handwashing after faecal contact with adult or child faeces. Despite the study groups' knowledge about diarrhoea, both groups showed a disconnection between their knowledge about routes of contamination and barriers to contamination. The most frequent reason for not treating water was the perceived safety of rain water in both the IG and CG. / The HWT adoption survey revealed poor storage and water-handling practices in both IG and CG, and that very few respondents knew how to use the HWT technologies correctly: The IG and CG were similar in perceived value attached to household water treatment. All HWT technologies had a lower likelihood of adoption compared to the likelihood of compliance indicators in both IG and CG. The users’ perceptions about efficacy, time taken and ease of use of the HWT technologies lowered the perceived value attached to the technologies. The assessment of the drinking water quality used by the study communities indicated that the improved sources had a lower geometric mean E. coli and total coliform count than the unimproved sources. Both categories of sources were of poor microbiological quality and both exceeded the Sphere Project (2004) and the WHO (2008) guidelines for total coliforms and E. Coli respectively The study communities’ predominant drinking water sources, surface water and rainwater were faecally contaminated (geometric mean E. coli load of 388.1±30.45 and 38.9±22.35 cfu/100 ml respectively) and needed effective HWT. The improved sources were significantly more likely than the unimproved sources to have a higher proportion of samples that complied with the WHO drinking water guidelines at source, highlighting the importance of providing improved water sources. The lowest levels of faecal contamination were observed between the collection and storage points which coincided with the stage at which HWT is normally applied, suggesting an HWT effect on the water quality. All water sources had nitrate and turbidity levels that exceeded the WHO stipulated guidelines, while some of the improved and unimproved sources had higher than permissible levels of lead, manganese and aluminium. The water source category and the mouth type of the storage container were predictive of the stored water quality. The active treater households had a higher percentage of samples that complied with WHO water quality guidelines for E. coli than inactive treater households in both improved and unimproved source categories. In inactive treater households, 65% of storage container water samples from the improved sources complied with the WHO guidelines in comparison to 72% of the stored water samples in the active treater households. However the differences were not statistically significant. The HWT technologies did not attain sector standards of effective performance: in descending order, the mean log10 reduction in E. coli concentrations after treatment of water from unimproved sources was PUR (log₁₀ 2.0), ceramic filters (log₁₀ 1.57), Aquatab (log₁₀ 1.06) and Waterguard (log₁₀ 0.44). The mean log10 reduction in E. coli after treatment of water from improved sources was Aquatab (log₁₀ 2.3), Waterguard (log₁₀ 1.43), PUR (log₁₀ 0.94) and ceramic filters (log₁₀ 0.16). The HWT technologies reduced the user’s daily exposure to water-borne pathogens from both unimproved and improved drinking water sources. The mean difference in exposure after treatment of water from unimproved sources was ceramic filter (log₁₀ 2.1), Aquatab (log₁₀ 1.9), PUR (log₁₀ 1.5) and Waterguard (log₁₀ 0.9), in descending order. The mean probability of infection with water-borne pathogens (using E.coli as indicator) after consumption of treated water from both improved and unimproved sources was reduced in users of all the HWT technologies. The difference in reduction between technologies was not statistically significant. The study concluded that despite the apparent need for HWT, the study households’ inadequate knowledge, poor attitudes and unhygienic practices make it unlikely that they will use the technologies effectively to reduce microbial concentrations to the standards stipulated by accepted drinking water quality guidelines. The structured method of HWT promotion in the intervention villages had not resulted in more hygienic water and sanitation KAP in the IG compared to the CG, or significant differences in likelihood of adoption and compliance with the assessed HWT technologies. Despite attaching a high perceived value to HWT, insufficient knowledge about how to use the HWT technologies and user concerns about factors such as ease of use, accessibility and time to use will impact negatively on adoption and compliance with HWT, notwithstanding their efficacy during field trials. Even though external support had been withdrawn, the assessed HWT technologies were able improve the quality of household drinking water and reduce the exposure and risk of water-borne infections. However, the improvement in water quality and reduction in risk did not attain sector guidelines, highlighting the need to address the attitudes, practices and design criteria identified in this study which limit the adoption, compliance and effective use of these technologies. These findings have implications for HWT interventions, emphasising the need for practice-based behavioural support alongside technical support.

Submitted in fulfillment of the requirements for the degree of Master of Engineering, Department of Industrial Engineering, Durban University of Technology, Durban, South Africa, 2017. / Access to clean and adequate water is a universal and basic human right that feeds into the 6th of the 17 Sustainable Development Goals (SDGs). This goal aims at ensuring availability and sustainable management of water and sanitation for all. Clean water is referred to as potable water, which is safe for human consumption and offer low risk of immediate or long term harm. Raw water undergoes rigorous processing which consists of coagulation, sedimentation, filtration, disinfection and storage, to produce potable water. Each module or stage consumes chemicals and energy resources and thus incurs costs. To achieve the aim of the study, which was to synthesize an optimised potable water treatment network and a water usage analysis model, the Umzinto Water Treatment Plant (UWTP) and its distribution system was used as the study area. This treatment plant is located within Umdoni, a local municipality of the Ugu District Municipality in KwaZulu-Natal Province, South Africa. This study’s objectives were fourfold and the first objective was to identify and quantify key raw water quality parameters affecting treatment at the UWTP. The second objective was to design a genetic algorithm for the potable water treatment process control. The third objective was to evaluate the Umzinto Water Distribution System’s Non-Revenue Water (NRW) while the fourth objective was to develop a model for water usage analysis. For the first objective, data for water quality parameters for the water treatment from July 2006 to June 2013 were statistically analysed. This data were collected from the UWTP’s historical records. To improve the data’s integrity it was pre-processed using cubic hermite interpolation. After the pre-processing trend lines and box plots were used to determine the parameters’ significance compared to the standard values stipulated in the South African National Standard (SANS 241). The trend lines were used to analyse the frequency of observations that were higher than the standard values according to SANS 241. The box plots were used to determine the minimum, median, maximum and mean of the data sets. The mean values for each parameter were compared to the SANS 241 value to determine their significance. The raw water quality parameters were then correlated to the chemical dosages for lime, polymer, potassium permanganate and chlorine. The key parameters selected from the correlation analysis were algal count, manganese (Mn), iron (Fe), Escherichia coli, total coliforms, colour, odour, conductivity, turbidity, suspended solids (SS), pH, temperature, total organic carbon (TOC,) and Hardness. A number of methods can be used to achieve such optimisation, including artificial neural networks, dynamic programming, linear and non-linear programming, and this study utilised a genetic algorithm as an optimisation tool to achieve the second objective of optimising water treatment at the UWTP. For the model development, data from the correlations obtained for objective 1 were used. The model was aimed at reducing the cost of chemical dosage and four chemical dosage prediction models were developed using genetic algorithms and these were then used to produce a combined chemical dosage cost prediction model. The programming interface utilised for these models was Matlab. In developing these models, the data were first pre-processed to remove outliers and fill in the blanks using a Microsoft Excel Add-in that was developed for this particular purpose. The next step involved a curve fitting exercise in Microsoft Excel 2013. Matlab was then used to code the genetic algorithm that combined and optimised the solutions obtained from the curve fittings. The results showed that genetic algorithms can be reliably used to predict the chemical dosages and hence reduce water treatment costs. After treatment, water is pumped into the distribution system for consumption. It is therefore important to ensure that all the pumped out treated water reaches the consumer. The third objective therefore assessed the NRW for the Umzinto Water Distribution System for the period between July 2013 and June 2014. The data used for this objective was provided by the Ugu District Municipality. The method used combined the top-down approach and the component-based approach. This combined approach was modified to enable the calculation of all the components that are required in a standard South African Water Balance. The results showed that the distribution system had a high value of NRW, which was 27.9% of the System Input Volume. The major component of NRW was Real Losses, that is, losses that can be mitigated by improving maintenance. The fourth objective was to develop a model for water usage analysis that would reduce the time taken to evaluate NRW and also improve the analysis of the NRW components using Microsoft Visual Basics 2012 and Microsoft SQL Server 2012 development interfaces. The Visual Basics enabled the development of a graphic user interface that was user-friendly and minimised the time taken to learn the software. The software platform developed was able to import the data required to construct a standard International Water Asssociation (IWA) Water Balance, calculate all the components of NRW, store historical data for the water distribution systems and report on a rolling year basis. A model for water usage analysis was developed and made available for usage by practitioners in Ugu District. The model was developed for the specific study area and further studies would be required in order to validate it in a different setting. The results obtained for the first objective led to the conclusion that, there was very high pollution emanating from communities and activities close to the raw water sources, especially the EJ Smith Dam. The results from the first objective were also used to determine parameters for the models developed in the second objective. From objective two it was concluded that genetic algorithms can be reliably used to predict chemical dosages and hence reduce water treatment costs. The third objective’s results showed that 27.9% of treated water pumped into the distribution system is NRW. Which is a concern because 65% of this are real losses which have maintenance related problems. The fourth objective’s results showed the practicality of designing model that could be used determine all the important components of NRW that would take time to evaluate manually. It would also store historical data for the water distribution system and report on a rolling year basis. Implementation of this software would help minimise the errors associated with manual calculation of NRW and improve the availability of data for research and analysis. From the research findings, it is recommended that the treatment plant should change the way it is dosing chemicals in the balancing tank. The method currently being used is prone to error. The analysis of NRW showed that Real Losses were a major challenge in the Umzinto Distribution System. There is need to develop a maintenance program to cater for leakage. Communities also need to be educated on the importance of reporting leakage in the network. / M

Submitted in fulfillment of the academic requirement for the degree Master of Engineering in Chemical Engineering, Department of Chemical Engineering, Faculty of Engineering and the Built Environment, Durban University of Technology, Durban, South Africa, 2017. / Provision of microbiologically safe drinking water for people living in the rural areas of developing countries remains a major challenge to date. One of the reasons is due to the inability to access potable water mainly because of poor existing water purification systems. Current measures have been put in place to address the challenges of rural water supply. Development of appropriate technologies such as decentralized water treatment supply in the form of point of use (POU) systems are been considered. In lieu of the above, an appropriate POU system known as the Remote Rural Water Treatment System (RRWTS) was developed at Durban University of Technology (DUT). The RRWTS is polyester based locally sourced Woven Fabric Microfiltration (WFMF) membrane system. The unit is made up of flat sheet modules that are assembled into a pack. It is a robust gravity driven system with the ability to remove suspended solids and colloids in the form of turbidity. The system has high flux of 35 ± 7 LMH and turbidity below 1 NTU, it has the ability to remove pathogens well above 95%. However, this does not comply with WHO and SANS drinking water standards of zero E. coli count/100 ml of treated water. In order to bring the water treated by RRWTS to a satisfactory level for drinking, it is then necessary to add a separate disinfection step like chlorination step to further remove the remaining microbial contaminants. Thus the main objective of the study was to evaluate the disinfection efficacy of two disinfectants namely waterguard and bromochlor tablet disinfectants and investigate their integration with the WFMF membrane. The study was categorised into three parts. The first part is the addition of disinfectants to unfiltered river water sources for the determination of residual chlorine and the most optimum dose that will yield effective disinfection and also evaluate the extent of E. coli removal by the disinfectants. The second stage was the filtration of four river water sources using the woven fibre membrane (WFM) to determine the efficiency of WFMF. Finally the effect of disinfection kinetics on disinfection was achieved by agitating the water after disinfection and allowing it to stand at different contact times. Performance of the RRWTS was determined by the amount of E. coli and turbidity removed during filtration using WFMF and by chemical disinfectants after filtration. The results on residual chlorine for different water sources showed that feed quality and disinfectant dose determines the quantity of residual chlorine on all the water sources. The effectiveness of chemical disinfectants in E. coli removal is affected by the quality of water to be disinfected. The study showed that turbidity plays a major role on disinfection by increasing chlorine demand on water sources with high turbidity levels. The WFMF demonstrated excellent filtration performance by producing permeates with turbidity less than 1 NTU for feed turbidities ranging from 10 to 200 NTU. The E. coli removal efficiency by WFMF was very high on all the water sources treated. There was 95-99.8% E. coli removal on raw feeds with influent E. coli ranging between 500 and 44500 CFU/100 ml. It was seen that major benefits are derived from integrating the WFMF (RRWTS) with chemical disinfection. The benefits includes; better disinfection that meets drinking water set guidelines of zero E. coli and improved quality of water. The need for disinfection kinetics in order to obtain superior disinfection was eliminated. The possibility of disinfection-by-product formation was reduced as smaller quantities of chemical disinfectants were required for complete disinfection on the filtered water. / M

M.Sc. / The world is focusing on increasing the number of people who have access to safe drinking water due to the ascending numbers of drinking water related illnesses reported annually in rural areas where water is not treated before consumption. To meet this goal, household water treatment has to be introduced especially in places where homes are wide apart making centralised water treatment improbable. Most readily available household water treatment systems (HWTS) such as membrane filters may not be affordable in rural areas due to power requirements and degree of ability to use and maintain them. This study was therefore aimed at designing and constructing HWTS using readily available material such as sand, gravel, zeolites and clays. Five HWTS were designed, built, evaluated and compared based on their ability to remove chemical contaminants such as iron, arsenic and fluorides from drinking water. The types of filters that were used during this study are the biosand filter (BSF), a modified biosand filter with zeolites (BSFZ), a silver impregnated porous pot (SIPP) filter, a ceramic candle filter (CCF) and a bucket filter (BF). Effectiveness of the filters in reducing physical parameters such as turbidity and visual colour was also assessed. The water treatment devices had the following flow rates; 1.74 L/h – 19.20 L/h (BSFZ), 0.81 L/h – 6.84 L/h (BSF), 0.05 L/h – 2.49 L/h (SIPP) and 1.00 L/h – 4.00 L/h (CCF). The flow rates were high at the early stages of filter use and decreased with increase in the volume of water filtered through. The flow rates of the filters were affected by the turbidity of intake water which was between 1.74 NTU – 42.93 NTU and correlated to chlorophyll a concentrations. The household water treatment technologies reduced turbidity to levels less than 1 NTU (> 90% reduction) in the following order SIPP > BSFZ > BSF > CCF > BF. The filters achieved greater than 60% retention of calcium, magnesium, iron and arsenic. These contaminants with the exception of arsenic were reduced to acceptable levels of the South African National Standard of drinking water (SANS 241, 2004). Compared to the other filters, the BSFZ performed better in removing nitrates, phosphates and fluorides although the overall retention efficiency was low. Total organic carbon was removed greatly by the CCF (39%) and the least removal was by the BF. The overall performance of the filters in reducing contaminants from drinking water was in the order BSFZ > BSF > SIPP > CCF > BF. Filter washing vi resulted in an overall increase in the flow rates of the filters but negatively affected turbidity reduction. The filters still removed contaminants after total cumulative volumes of 1200 L (BSFZ, BSF, CCF and BF) and 300 L (SIPP) were filtered through the devices. The five evaluated filters have several advantages to the readily available technologies and the advantages include ease of construction, operation and maintenance. The filters are gravity driven and work independent of temperature. These HWTS incorporate safe storages fitted with spigots to eliminate recontamination of water when it is drawn for use. The filters can produce enough drinking and cooking water for a family of six members due to their high flow rates. The BSFZ, BSF, SIPP, CCF and BF may therefore be considered for treating contaminated water at household scale in places where water is taken directly from the source without treatment.

Submitted in fulfillment of the requirements for the degree of Master of Engineering in Chemical Engineering, Durban University of Technology. Durban. South Africa, 2015. / Several areas in the world such as the United States of America, Sri Lanka, China, Argentina, Canada, Tanzania, Kenya, South Africa and many others have a problem of high fluoride content in drinking water. Generally fluoride levels above 1.5 ppm in water may result in dental and skeletal fluorosis in humans depending on quantity consumed (Fan et al., 2003; Meenakshi, 2004). Remote rural areas where there are no water treatment facilities are more vulnerable to this problem. Adsorbents such as activated alumina and FR-10 resin seem to have a potential for successful application in rural areas. These methods however require pre-treatment if the feed has high turbidity. A membrane based system called woven fabric microfiltration gravity filter (WFMFGF) developed by Durban University of Technology proved to be suitable for turbidity removal. The main objective of this research was to develop a small water treatment system for fluoride removal. The small water treatment system developed in this study consists of WFMFGF for pre-treatment and an adsorption column. The WFMFGF is made up of a 40 L container packed with 15 immersed flat sheet membrane elements. The operation of the WFMFGF is in batch mode, driven by varying static head. The static head variation results in flow rate variation through the system. This in turn result in variation of contact time, velocity as well as pressure drop in the fluoride removal unit. Specific objectives of the study were: (1) to establish the maximum and minimum flow rates through the WFMFGF system, the total run time before cleaning is required and the best cleaning method for this particular membrane system. (2) to evaluate and compare the performance of activated alumina and FR-10 resin on varying contact time, velocity and pressure drop on the fluoride removal unit. The adsorbents were also compared on adsorption capacity, cost and ease of operation. The minimum and maximum flow rates through the WFMFGF were found to be 5 l/hr and 100 l/hr respectively. It was found that the system can be run for more than a month before requiring cleaning. The suitable cleaning method was found to be soaking the membranes in 0.0225 percent sodium hypochlorite solution overnight and brushing them using a plastic brush. The comparison of the performance of FR-10 resin to activated alumina found that the adsorbents gave equal performance based on the given criteria. FR-10 resin had higher adsorption capacity, gave good quality treated water even with shorter contact time and operated at wider velocity range. Activated alumina on the other hand had an advantage of lower costs, lower pressure drop and ease of use. According to Pontius (1990), the performance of activated alumina can be improved by intermittent operation. Point of use (POU) systems are generally operated intermittently. This improves the fluoride removal efficiency of activated alumina giving it more advantage over FR-10 resin. Based on this activated alumina was selected as the best adsorbent for the system. After the adsorbent was selected, the adsorption column was designed. The column operation regime was 3.5 minutes minimum contact time and 1.17 to 7.8 m/hr velocity range. The activated alumina adsorption capacity was 1.53mg/g. The column had an inside diameter of 70 mm. It was packed with activated alumina to a bed height of 400 mm. The column inlet and outlet pipes were made of PVC with a standard pipe size of 20 mm outside diameter. A valve at the column inlet pipe allowed water to flow through the system.

Chapter I: This chapter briefly gives an introduction about microorganisms, their varieties, growth, reproduction etc. In particular, about bacterial function. A sincere attempt is made to review this briefly, including an account of the studies already reported in the literature. Chapter II deals with the antimicrobial activity of Ag/agar film on Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Candida albicans (C. albicans). In particular, films were repeatedly cycled for its antimicrobial activity. The antimicrobial activity of Ag/agar film was found to be in the order, C. albicans > E. coli > S. aureus. Chapter III describes the synthesis of Ag@AgI NPs in agarose matrix. A detailed antibacterial studies including repetitive cycles are carried out on E. coli and S. aureus bacteria. EPR and TEM studies are carried out on the Ag@AgI/Agarose and the bacteria, respectively, to elucidate a possible mechanism for killing of the bacteria. The hybrid could be recycled for the antibacterial activity many times and is found to be non toxic towards human cervical cancer cell (HeLa cells). Chapter IV reports the antibacterial efficacy of silver nanoparticles (Ag NPs) deposited alternatively layer by layer (LBL) on chitosan polymer in the form of a thin film over a quartz plate and stainless steel strip against E. coli. AFM studies are carried out on the microbe to know the morphological changes affected by the hybrid film. The hybrid films on aging (3 months) are found to be as bioactive as before. Cytotoxicity experiments indicated good biocompatibility. Chapter V describes the fabrication of carbon foam porous electrode modified with reduced graphene oxide-Ag nanocomposites. The device can perform sterilization by killing pathogenic microbes with the aid of just one 1.5V battery with very little power consumption. Chapter VI Here we have studied in particular a property say the influence of surface defect in the production of ROS by ZnO NPs and in turn the bactericide activity. Secondly, a homogeneous ZnO and ZnO/Ag nanohybrid has been synthesized by employing chitosan as mediator. The synergistic antibacterial effect of ZnO/Ag nanohybrid on bacteria is found to be more effective, compared to the individual components (ZnO and Ag). A possible mechanism has been proposed for the death of bacteria by ZnO/Ag nanohybrid, based on EPR studies and TEM studies.