D.Ing. (Mechanical Engineering) / Most coal fired power stations in South Africa are equipped with Electrostatic Precipitators (ESP's). With the ongoing reduction of allowable emissions, as negotiated with the Chief Air . Pollution Control Officer (CAPCO) of the Department of Environmental Affairs and Tourism (DEAT), ways to reduce emissions are sought. In the case of emission levels exceeding the values set by the controlling authority load losses are required for compliance. This however has the effect of plant operating inefficiently and a loss of revenue will result. Specifically in times of growing demand, when more and more of the currently installed generation capacity is required to satisfy the demand, forced load reductions are not desirable. Performance enhancement of ESP's can be achieved by means of system optimisation. Research was initiated to achieve the capability of modelling important dynamic aspects of ESP performance using Computational Fluid Dynamics (CFD). This modelling capability would create the opportunity to investigate the different influencing factors which govern the dust collection efficiency. In the past ESP flow has been modelled by means of mathematical modelling with various degrees of success world-wide. It was found that the accuracy of flow modelling as presently carried outby researchers world wide, is not sufficient to represent the complex inlet flow. Commercially available performance simulation software is based on empirical modelling principles and do not include the complexity of flow fields and re-entrainment and thus results have been limited in accuracy. Computational fluid dynamics software is commercially available and widely used to simulate industrial flow for plant design and optimisation. This technology has been applied with increasing confidence and success in the past. However, often the physical phenomena relevant for the performance simulation of the plant is not integrated into the code and specialised user routines are created to achieve a valid performance model. This research study introduces a unique integrated simulation methodology based on a commercial CFD code. The work focuses on the accurate modelling of fluid flow and collection dynamics in an ESP. User subroutines have been created to simulate particle charging, collection and re-entrainment. The results of the simulations are compared to measurement at actual plant.

This thesis focuses on pioneering a scalable route to fabricate quantum information devices based upon single InAs/InP quantum dots emitting in the telecommunications wavelength band around 1550 nm. Using metallic gates in combination with nanotemplate, site-selective epitaxy techniques, arrays of single quantum dots are produced and electrostatically tuned with a high degree of control over the electrical and optical properties of each individual quantum dot. Using metallic gates to apply local electric fields, the number of electrons within each quantum dot can be tuned and the nature of the optical recombination process controlled. Four electrostatic gates mounted along the sides of a square-based, pyramidal nanotemplate in combination with a flat metallic gate on the back of the InP substrate allow the application of electric fields in any direction across a single quantum dot. Using lateral fields provided by the metallic gates on the sidewalls of the pyramid and a vertical electric field able to control the charge state of the quantum dot, the exchange splitting of the exciton, trion and biexciton are measured as a function of gate voltage. A quadrupole electric field configuration is predicted to symmetrize the product of electron and hole wavefunctions within the dot, producing two degenerate exciton states from the two possible optical decay pathways of the biexciton. Building upon these capabilities, the anisotropic exchange splitting between the exciton states within the biexciton cascade is shown to be reversibly tuned through zero for the first time. We show direct control over the electron and hole wavefunction symmetry, thus enabling the entanglement of emitted photon pairs in asymmetric quantum dots. Optical spectroscopy of single InAs/InP quantum dots atop pyramidal nanotemplates in magnetic fields up to 28T is used to examine the dispersion of the s, p and d shell states. The g-factor and diamagnetic shift of the exciton and charged exciton states from over thirty single quantum dots are calculated from the spectra. The g-factor shows a generally linear dependence on dot emission energy, in agreement with previous work on this subject. A positive linear correlation between diamagnetic coefficient and g-factor is observed.

Electrostatic charge generation is unavoidable in gas-solid fluidized beds due to the repeated particle-particle and particle reactor wall contacts and separations. In industrial operations such as in polyethylene production this phenomenon results in the significant problem of reactor wall fouling, known as “sheeting”. To better understand the underlying charging mechanisms involved in gas-solid fluidized beds in an attempt to eliminate and/or reduce the effect a novel on-line electrostatic charge measurement technique was developed, which concurrently provided information on both the degree of fluidized bed electrification and reactor wall fouling. A Faraday cup replaced the windbox of the fluidized bed while another cup was placed at the top of the column. The distributor plate was uniquely designed for the systematic removal of bed particles and those adhered to the column wall for their charge measurement with the bottom Faraday cup, and the charge of the entrained particles was measured by the top Faraday cup. This is the first study which allowed the charge measurement of particles in the bulk of the bed, particles adhered to the column wall, and those entrained, simultaneously. In addition, this method uniquely permitted the evaluations of the degree of reactor wall fouling under different operating conditions. An experimental program was designed to investigate the influence of bed hydrodynamics (fluidizing gas velocity and particle size), fluidization column wall material, and the addition of different solid additives. Fluidizing particles were polyethylene resin from an industrial reactor. Bi-polar charging was observed where the elutriated particles were oppositely charged compared to those in the bulk of the bed and those adhered to the column wall. Particles within the wall coating were also found to be bi-polarly charged. With the resin tested as received, a certain sized particles (350-575 µm) adhered to the column wall. The specific charge of the particles near the column wall was found not to be a definite indication of the amount of wall fouling. Increasing the gas velocity promoted wall fouling and elevated the charge density of the particles within both bubbling and slugging flow regimes. The effect of solid additive injection was examined with two static drivers known to reduce wall fouling in industrial operations, a deactivated catalyst, and the catalyst support. It was found that the catalyst promoted, while one of the static drivers reduced wall fouling.

Polymer based microelectromechanical systems (MEMS) micromachining is finding more interest in research and applications. This is due to its low cost and less time processing compared with silicon MEMS. SU-8 is a photo-patternable polymer that is used as a structural layer for MEMS and microfluidic devices. In addition to being processed with low cost, it is a biocompatible material with good mechanical properties. Also, amorphous silicon (α-Si) has found use as a sacrificial layer in silicon MEMS applications. α-Si can be deposited at large thicknesses for MEMS applications and also can be released in a dry method using XeF2 which can solve stiction problems related to MEMS applications. In this thesis, an SU-8 MEMS process is developed using amorphous silicon (α-Si) as a sacrificial layer. Electrostatic actuation and sensing is used in many MEMS applications. SU-8 is a dielectric material which limits its direct use in electrostatic actuation. This thesis provides a MEMS process with two conductive metal electrodes that can be used for out-of-plane electrostatic applications like MEMS switches and variable capacitors. The process provides the fabrication of dimples that can be conductive or non-conductive to facilitate more flexibility for MEMS designers. This SU-8 process can fabricate SU-8 MEMS structures of a single layer of two different thicknesses. Process parameters were tuned for two sets of thicknesses which are thin (5-10μm) and thick (130μm). Chevron bent-beam structures and different suspended beams (cantilevers and bridges) were fabricated to characterize the SU-8 process through extracting the density, Young’s Modulus and the Coefficient of Thermal Expansion (CTE) of SU-8. Also, the process was tested and used as an educational tool through which different MEMS structures were fabricated including MEMS switches, variable capacitors and thermal actuators.

The first objective of the dissertation is to develop a suitable reduced order model capable of investigating the nonlinear mechanical behavior of von-Karman plates under electrostatic actuation. The second objective is to investigate the nonlinear static and dynamic behavior of rectangular microplates under small and large actuating forces. In the first part, we present and compare various approaches to develop reduced order models for the nonlinear von-Karman rectangular microplates actuated by nonlinear electrostatic forces. The reduced-order models aim to investigate the static and dynamic behavior of the plate under small and large actuation forces. A fully clamped microplate is considered. Different types of basis functions are used in conjunction with the Galerkin method to discretize the governing equations. First we investigate the convergence with the number of modes retained in the model. Then for validation purpose, a comparison of the static results is made with the results calculated by a nonlinear finite element model. The linear eigenvalue problem for the plate under the electrostatic force is solved for a wide range of voltages up to pull-in. In the second part, we present an investigation of the static and dynamic behavior of a fully clamped microplate. We investigate the effect of different non-dimensional design parameters on the static response. The forced-vibration response of the plate is then investigated when the plate is excited by a harmonic AC load superimposed to a DC load. The dynamic behavior is examined near the primary and secondary (superharmonic and subharmonic) resonances. The microplate shows a strong hardening behavior due to the cubic nonlinearity of midplane stretching. However, the behavior switches to softening as the DC load is increased. Next, near-square plates are studied to understand the effect of geometric imperfections of microplates. In the final part of the dissertation, we investigate the mechanical behavior of initially curved microplates. Microplates often experience an initial curvature imperfection, due to the micro fabrication process, which affects significantly their mechanical behavior. In this case a clamped-free-clamped-free microplate is considered. We validate the reduced order model by comparing the calculated static behavior and the fundamental natural frequency with those computed by a finite element model. As case studies, we consider two commonly encountered profiles of the initial curvature imperfection and study their effects on both the static and dynamic responses of the microplates. Next, an initially curved microplate made of silicon nitride is studied. The static behavior of the microplate is investigated when applying a DC voltage. Then, the dynamic behavior of the microplate is examined under the application of a harmonic AC voltage, superimposed to a DC voltage. Simulation results calculated by the reduced order model are compared with experimental data for model validation purpose, which show good agreement.

No description available.

The design of biocompatible synthetic surfaces is an important issue for medical applications. Surface modification techniques provide good approaches to control the interactions between living systems and implanted materials by modifying the surface characteristics. This thesis work demonstrates the feasibility and effectiveness of the novel and low-cost electrostatic self-assembly (ESA) technique for the manufacturing of biocompatible thin film coatings. The ESA process is based on the alternating adsorption of molecular layers of oppositely charged polymers/nanoparticles, and can be applied in the fabrication of well-organized multilayer thin films possessing various biocompatible properties. ESA multilayer assemblies incorporating various biomaterials including metal oxides and polymers were fabricated, the uniformity, thickness, layer-by-layer linearity, and surface morphology of the films were characterized by UV/vis spectroscopy, ellipsometry, and AFM imaging. Preliminary biocompatibility testing was conducted, concentrating on contact angle surface characterization and the in vitro measurements of protein adsorption. The use of Fourier Transform Infrared Reflection-Absorption Spectroscopy (FT-IRAS) for the investigation of the protein adsorption behavior upon the ESA multilayer films is presented. / Master of Science

京都大学 / 0048 / 新制・課程博士 / 博士(農学) / 甲第20426号 / 農博第2211号 / 新制||農||1048(附属図書館) / 学位論文||H29||N5047(農学部図書室) / 京都大学大学院農学研究科応用生命科学専攻 / (主査)教授 加納 健司, 教授 植田 充美, 教授 三上 文三 / 学位規則第4条第1項該当 / Doctor of Agricultural Science / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(農学) / 甲第20715号 / 農博第2244号 / 新制||農||1053(附属図書館) / 学位論文||H29||N5081(農学部図書室) / 京都大学大学院農学研究科応用生命科学専攻 / (主査)教授 加納 健司, 教授 宮川 恒, 教授 三芳 秀人 / 学位規則第4条第1項該当 / Doctor of Agricultural Science / Kyoto University / DFAM

No description available.