This diploma thesis describes the work performed in the optimization of the corporate network in the company Alps Electric Czech to expand the amount of information obtained about the state of the network and thus improve the response of the IT department to potencial errors. During the optimization, a monitoring system was also deployed and its connection to the helpdesk and a tailor-made website running on the Flask microframework. With the gradual deployment, adjustments were made based on feedback from the IT department staff. Overall, the network has become more clarified, increasing the efficiency of maintenance and service.

This diploma project summarizes a theoretical introduction regarding the issue of traffic light control. Further there is industrial communication discussed, where they are the Ethernet / IP protocol and the Modbus TCP protocol described more in detail. The following is the description of the Logix series programmable controllers. Then the diploma follows up with market research in order to find the most suitable development kit which is used as a trial prototype. Then it is concerned with a development kit with a communication module from AND-TECH company. Software was developed on them, more specifically a library for processor ports, memory and the Modbus TCP protocol. After verifying the functionality of the software, the hardware design was started. From the first site it is development kit and module and from the second site there are input and output circuits. There must be the assessment of the results found during the test operation. The end of the document describes incorrect steps that were repaired in hardware.

This Master`s thesis concern with problematic of connection analog sensors with voltage output 0-10V to a ethernet communication network. Due to a quick evolution and an application ethernet nets to industry and building technologies is possible to use this solution for connection remote diagnostics and setting of existing analog sensors without bus communication interfaces on instrumentation level of field bus networks. The converter is based on Rabbit module, which can be used like webserver for setting, calibration and data recording. For purpose of wide converter use the data output will be purvey on ethernet interface by Modbus TCP and on asynchronous serial interface RS232. First part of thesis is aimed on description of existing solutions and introduction with principles of linearization and calibration of A/D converters. Description of communication standard Modbus TCP widely used in industry applications. Second part of thesis describes design a realization of project. Here is described equipment block diagram with detail description of each block and devices used. In the part of implementation is description of device firmware with program function description and control. Last part is engage with module function verification supported with plantz of measurements and tests. The thesis is ended with evaluation results, knowledge and detections found out in development of project.

The aim of this master's thesis is suggestion and following realization of voice transmission over the local network equipment and a description of used circuits and solutions in terms of hardware and software. This thesis deals with digitization of low-frequency signals, the structure of IP and UDP protocols, implementation of TCP/IP stack cIPS

The thesis deals with the implementation of Ethernet-based network communication interface into FPGA chip. VHDL programming language is used for description of the hardware. The interface includes the implementation of link-layer Ethernet protocol and network protocols such as IPv4, ARP, ICMP and UDP. The final design allows bi-directional communication on the transport-layer level of TCP/IP model. The designed interface was implemented into Virtex5 FPGA chip on development board ML506 by Xilinx.

Project is focused to development of security unit for security of homes, flats and other similar spaces against intruders (thieves). Design is focused to solution of hardware and firmware for security units and their control software for PC. Hardware design solve supply over ethernet PoE, backup of supply, connection securities sensors to security unit. Firmware prevents failure of units and it is communicating with sensors and PC. Software in PC provides settings of security units, deactivating of alarm and measure temperature by security unit.

In this work I aimed at designing a universal system for testing either STM32F407/417 by STMicroelectronics and later various sensors and communication buses. The result then is a main board with many specific connectors for individual buses even with connectors making all I/O pins accessible at the same time. Thanks to advanced switching regulators the power supply is capable of accepting a wide range of sources like single Li-Ion cell, pair of alkaline cells, 12V Lead battery, common wall power adapters (both DC and AC up to 15 Vpp ), USB, laboratory power supplies with multiple outputs and finally POE (Power Over Ethernet). Supply voltages are supervised by voltage comparators with an optical signalisation. (It is possible to determine the sick branch without a measuring instrument and blowing components in the most cases.) Another important parameter was a robustness of the supply and communication lines. There is a number of TVSs, chokes, and big and low ESR capacitors A PC software is intended for a basic functionality demonstration only.

The subject of master’s thesis is introduction with the principles of measuring voltage, current and electrical power in DC and AC systems. Is designed measurement system for normal household. Measurement system includes pricing and client billing. User interface Ethernet-based is implemented.

This thesis deals with an electronic circuit and a PCB of a modular RGB LED display with the Ehernet interface. Firstly, author describes a RGB colour model, features of RGB LED displays, ways of control them. The next chapter contains a short description of the Ethernet interface, UDP and TCP protocols and a lwIP TCP/IP stack. The last theoretical chapter is an introduction to ARM Cortex-M3 and Cortex-M4 based microcontrollers. The next chaper is deals with a hardware design of the modular RGB LED display. The device is designed to be modular. Individual devices can be combosed together and create a larger display. Data from the Ethernet interface will be displayed on the RGB LED matrix, resolution of the matrix is 32 × 32 (1024 diodes). A refresh frequency is 100 Hz, a color depth is High color (16 bits) and a scanning 1/16 (two rows is driven at the same time). The next chapter describes the firmware for the RGB LED display, all its logical parts including a web page. Author also created the PC application, which sends pictures using UDP protocol to individual modules.

The master’s thesis describes development of control system for automatic mouth-organ. The process of development is divided into three parts: a concept of control system, design of hardware parts and development of software parts. Controlled device, system requirements and general design of the hardware and software components are described in the concept of control system. The detailed hardware design includes next processes: electronic component selection, printed circuit board design, assembly and debugging. The result of this chapter is electronic system, which function correctly. The aim of the last chapter is to specify and explain development of software parts of control system. Installation of required software and important aspects of control software and user interface development are described in this chapter. The goal of the thesis is to create a control system, which will function correctly and reliably.