abstract: Droplet-structure interactions play a pivotal role in many engineering applications as droplet-based solutions are evolving. This work explores the physical understanding of these interactions through systematic research leading to improvements in thermal management via dropwise condensation (DWC), and breathable protective wearables against chemical aerosols for better thermoregulation. In DWC, the heat transfer rate can be further increased by increasing the nucleation and by optimally ‘refreshing’ the surface via droplet shedding. Softening of surfaces favor the former while having an adverse effect on the latter. This optimization problem is addressed by investigating how mechanical properties of a substrate impact relevant droplet-surface interactions and DWC heat transfer rate. The results obtained by combining droplet induced surface deformation with finite element model show that softening of the substrates below a shear modulus of 500 kPa results in a significant reduction in the condensation heat transfer rate. On the other hand, interactions between droplet and polymer leading to polymer swelling can be used to develop breathable wearables for use in chemically harsh environments. Chemical aerosols are hazardous and conventional protective measures include impermeable barriers which limit the thermoregulation. To solve this, a solution is proposed consisting of a superabsorbent polymer developed to selectively absorb these chemicals and closing the pores in the fabric. Starting from understanding and modeling the droplet induced swelling in elastomers, the extent and topological characteristic of swelling is shown to depend on the relative comparison of the polymer and aerosol geometries. Then, this modeling is extended to a customized polymer, through a simplified characterization paradigm. In that, a new method is proposed to measure the swelling parameters of the polymer-solvent pair and develop a validated model for swelling. Through this study, it is shown that for this polymer, the concentration-dependent diffusion coefficient can be measured through gravimetry and Poroelastic Relaxation Indentation, simplifying the characterization effort. Finally, this model is used to design composite fabric. Specifically, using model results, the SAP geometry, base fabric design, method of composition is optimized, and the effectiveness of the composite fabric highlighted in moderate-to-high concentrations over short durations. / Dissertation/Thesis / Doctoral Dissertation Mechanical Engineering 2019

PhD Thesis / In this thesis, experiments are described which study the elastocapillary interactions between liquids and taut solid films. The research employs contact angle measurements to elucidate how capillary forces deform compliant solid structures, but also to attain fundamental insight into the energy of interfaces involving amorphous solids. The majority of the work focuses on how capillary deformations of compliant elastic membranes introduce modifications to descriptions of common wetting phenomena. Particular focus is given to studying partial wetting in the presence of compliant membranes in various geometries: droplet on a free-standing membrane, droplet capped by a membrane but sessile on a rigid substrate, and droplet pressed between two free-standing membranes. The mechanical tension in these membranes is found to play an equivalent role as the interfacial tensions. As such, the mechanical tension is incorporated into Young-Dupre's law (capped droplet on a rigid substrate) or Neumann's triangle (droplet on free-standing membrane), leading to departures from the classical wetting descriptions. In addition, one study is conducted investigating how viscous dewetting is affected by the liquid film being capped by an elastic film. The results of this study show that the dewetting rate and rim morphology are dictated by the elastic tension. Another important aspect of the work is demonstrating the utility of anisotropic membrane tension for liquid patterning. A biaxial tension is shown to produce droplets and dewetting holes which are elongated along the high tension direction. The compliant membrane geometry can also be designed to produce droplets and holes with square morphology. In the final project, the surface energy of strained glassy and elastomeric solids is studied. Glassy solids are shown to have strain-dependent surface energies, which implies that surface energy (energy per unit area) and surface stress (force per unit length) are not equivalent for this class of materials by virtue of the Shuttleworth equation. On the other hand, this study provides strong evidence that surface energy and surface stress are equivalent for elastomeric interfaces. / Thesis / Doctor of Philosophy (PhD)

Dans cette thèse à l’interface entre élasticité et capillarité, nous présentons tout d’abord une instabilité élastique, le claquage, revisitée dans un contexte élastocapillaire. En déposant une goutte d’eau sous une lamelle flambée en position basse, nous parvenons à déclencher une instabilité de claquage à contresens de la gravité. Cette démonstration de la prédominance des effets capillaires à petite échelle s’accompagne d’une étude des positions d’équilibre et de la stabilité de systèmes goutte-lamelle. Nous démontrons l’influence importante de la taille et de la position de la goutte le long de la lamelle, puis étendons notre étude au cas de bulles ou de gouttes condensées à partir de vapeur d’eau. Enfin, nous nous intéressons à l’aspect dynamique de l’instabilité, qui est dictée principalement par l’élasticité, y compris dans le cas élastocapillaire.Nous mettons ensuite en évidence un phénomène surprenant : la dynamique de descente d’une goutte d’eau sur un élastomère silicone présente deux régimes successifs, caractérisés par deux vitesses différentes. Nous montrons que les chaînes libres non réticulées présentes dans l’élastomère sont à l’origine de cette dynamique inattendue. La goutte est progressivement recouverte par des chaînes de silicone, et sa vitesse change brutalement lorsqu’une concentration surfacique critique est atteinte, ce qui se traduit par une transition brutale de tension de surface. Nous nous intéressons aux vitesses de gouttes dans les deux régimes ainsi qu’aux échelles de temps mises en jeu lors de l’extraction de chaînes non réticulées, et montrons que l’extraction de ces chaînes se produit au niveau de la ligne triple. / This thesis focuses on interactions between liquids and elastic solids. We first revisit the snap-through instability from an elastocapillary point of view, showing that capillary forces are able to counterbalance gravity by inducing snap-through with a droplet deposited below a downward buckled elastic strip clamped at both ends. Equilibrium, stability, and dynamics of drop-strip systems are investigated, demonstrating the influence of droplet size and droplet position along the buckled strip, and showing that capillarity is driving the system toward instability but elasticity is ruling the subsequent dynamics. Spin-off versions of the experiment are also designed, including a humidity-controlled mechanical switch and upscaled experiments using soap bubbles.We then focus on interactions between silicone elastomers and aqueous droplets to understand the mechanisms underlying an unexpected two-regime droplet dynamics observed on vertical silicone elastomer plates. After demonstrating that this two-regime dynamics is due to the presence of uncrosslinked oligomers in the elastomer, we show that the speed transition coincides with a surface tension transition. A quantitative study of the droplets speeds in the two regimes is performed, and the timescale needed for uncrosslinked oligomers to cover the water-air interface is investigated both for sessile and moving droplets. We eventually show that uncrosslinked chains are extracted from the elastomer at the water - air - silicone elastomer triple line, and demonstrate that extraction occurs in various setups such as partially immersed silicone elastomer plates or air bubbles sliding up PDMS planes immersed in a water bath.