Following the continually increasing demand for high-density interconnection and multilayer packaging for chips, solder bump size has decreased significantly over the years, this has led to some challenges in the reliability of interconnects. This thesis presents research into the resulting effects of miniaturization on the interconnection with Sn-solder, especially focusing on the full intermetallics (IMCs) micro-joints which appear in the 3D IC stacking packaging. Thereby, systematic studies have been conducted to study the microstructural evolution and reliability issues of Cu-Sn and Cu-Sn-Ni IMCs micro-joints. (1) Phenomenon of IMCs planar growth: The planar IMCs interlayer was asymmetric and composed of (Cu,Ni)6Sn5 mainly in Ni/Sn (2.5~5 μm)/Cu interconnect. Meanwhile, it was symmetric two-layer structure in Cu/Sn (2.5~5 μm)/Cu interconnect with the Cu3Sn fine grains underneath Cu6Sn5 cobblestone-shape-like grains for each IMCs layer. Besides, it is worth noticing that the appearance of Cu-rich whiskers (the mixture of Cu/Cu2O/SnOx/Cu6Sn5) could potentially lead to short-circuit in the cases of ultra-fine ( < 10 μm pitch) interconnects for the miniaturization of electronics devices. (2) Microstructural evolution process of Cu-Sn IMCs micro-joint: The simultaneous solidification of IMCs interlayer supressed the scalloped growth of Cu6Sn5 grains in Cu/Sn (2.5 μm)/Cu interconnect during the transient liquid phase (TLP) soldering process. The growth factor of Cu3Sn was in the range of 0.29~0.48 in Cu-Cu6Sn5 diffusion couple at 240~290 °C, which was impacted significantly by the type of substrates. And the subsequent homogenization process of Cu3Sn grains was found to be consistent with the description of flux-driven ripening (FDR) theory. Moreover, Kirkendall voids appeared only in the Cu3Sn layer adjacent to Cu-plated substrate, and this porous Cu3Sn micro-joint was mechanically robust during the shear test. (3) Microstructural evolution of Cu-Sn-Ni IMCs micro-joint: There was obvious inter-reaction between the interfacial reactions in Ni/Sn (1.5 μm)/Cu interconnect. The growth factor of (Cu,Ni)3Sn on Cu side was about 0.36 at 240 °C, and the reaction product on Ni side was changed from Ni3Sn4 into (Cu,Ni)6Sn5 with the increase of soldering temperature. In particular, the segregation of Ni atoms occurred along with phase transformation at 290 °C and thereby stabilized the (Cu,Ni)6Sn5 phase for the high Ni content of 20 at.%. (4) Micro-mechanical characteristics of Cu-Sn-Ni IMCs micro-joint: The Young s modulus and hardness of Cu-Sn-Ni IMCs were measured by nanoindentation test, such as 160.6±3.1 GPa/ 7.34±0.14 GPa for (Cu,Ni)6Sn5 and 183.7±4.0 GPa/ 7.38±0.46 GPa for (Cu,Ni)3Sn, respectively. Besides, in-situ nano-compression tests have been conducted on IMCs micro-cantilevers, the fracture strength turns out to be 2.46 GPa. And also, the ultimate tensile stress was calculated to be 2.3±0.7 GPa from in-situ micro-bending tests, which is not sensitive with the microstructural change of IMCs after dwelling at 290 °C.

Further understanding of mesoscale slip mechanics is crucial to future development of polycrystalline metals with improved performance. The research contained within this thesis aims to characterize localized mesoscale slip on slip bands further through two studies. First, a comprehensive comparison of slip system identification techniques was carried out to further validate each method as well as compare advantages and disadvantages of each. Second, slip bands in the presence of grain boundaries were studied to better characterize the dislocation content and behavior. In the first study, the use of SEM-DIC, AFM, ECCI, and HR-EBSD to characterize slip-system activity was assessed on the same material volume of Ti-7Al. This study presents a robust comparison of the various methods for the first time, including an assessment of their advantages and disadvantages, and how they can be used effectively in a complementary manner. The analysis of the different approaches was carried out in a blind manner independently at three different universities. A Ti-7Al specimen was deformed in uniaxial tension to approximately 3% axial strain, and the active slip systems were independently identified using (i) trace analysis; (ii) in-SEM digital image correlation, (iii) observations of residual dislocations from ECCI, and (iv) long-range rotation gradients through HR-EBSD, with consistent trace identification in all cases. Displacement data from AFM was used to augment the SEM-DIC displacement data by providing complementary out of plane displacement information. Furthermore, short-range dislocation gradients (measured by DIC) provided insight into the residual geometrically necessary dislocation (GND) content, and was consistent with the GND content extracted from EBSD data and ECCI images, confirming the presence of residual GNDs on the dominant slip systems resulting in visible slip bands. These approaches can be used in tandem to provide multi-modal information on slip band identification, strain and orientation gradients, out-of-plane displacements, and the presence of GNDs and SSDs, all of which can be used to inform and validate the development of dislocation-based crystal plasticity and strain gradient models. In the second study, shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m'-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

Plagioclase is the most abundant mineral in the lower crust and it is thus important to constrain the behaviour of plagioclase during deformation. Anorthosites, which are plagioclase-rich rocks, are common in Archaean cratons but their origin and rheological importance is still debated. The aims of this thesis are to 1) describe a newly discovered Archaean anorthosite complex (Naajat Kuuat, SW Greenland), investigate its origin and a possible genetic relationship between the anorthosite and associated mafic-ultramafic rocks and 2) to study the rheology and deformation mechanisms in plagioclase-rich rocks. The main focus of this thesis is on the deformation studies. (1) Geochemical whole-rock analyses from the Naajat Kuuat complex are indicative for an origin near a subduction zone setting. A genetic link by crystal fractionation between the anorthosite and associated mafic-ultramafic units is inferred. (2) Deformation behaviour of plagioclase is assessed from analyses of three anorthosite units deformed during different conditions. Samples were analysed using the electron backscatter diffraction technique (EBSD) in combination with optical and chemical analyses. All three case studies show significant strain localisation related to grain size reduction. A wet anorthosite deformed at dry conditions (T ~675-700°C) was dynamically recrystallised. Continuous bands of recrystallised grains developed a texture yet display microstructures and grain relationships indicative for grain size sensitive creep, suggesting that the rheology followed a Newtonian flow law. In the other two studies, samples with initially dry and wet composition, respectively, have experienced deformation during fluid present conditions at T ~550-620°C. These two samples show that fluids effectively caused reactions, replacements and aided strain localisation during deformation at mid crustal conditions. / At the time of the doctoral defence the following papers were unpublished and had a status as follows: Paper 1: Manuscript; Paper 2 Manuscript; Paper 3 Manuscript.

Formable Advanced High-Strength Steels (AHSS) have a unique combination of strength and ductility, making them ideal in the effort to lightweight vehicles. The AHSS in this study, Quenched and Partitioned 1180, rely on the Transformation Induced Plasticity (TRIP) effect, in which retained austenite (RA) grains transform to martensite during plastic deformation, providing extra ductility via the transformation event. Understanding the factors involved in RA transformation, such as local strain and grain attributes, is therefore key to optimizing the microstructure of these steels. This research seeks to increase understanding of those attributes and the correlations between microstructure and RA transformation in TRIP steels. To measure local strain, the viability of using forescatter detector (FSD) images as the basis for DIC study is investigated. Standard FSD techniques, along with an integrated EBSD / FSD approach (Pattern Region of Interest Analysis System), are both analyzed. Simultaneous strain and microstructure maps are obtained for tensile deformation up to around 6% strain. The method does not give sub-grain resolution, and surface feature evolution prevents DIC analysis across large strain steps; however, the data is easy to obtain and provides a natural set of complementary information for the EBSD analysis. In-situ tensile tests combined with EBSD allow RA grain and neighboring attributes to be characterized and corresponding transformation data to be obtained. However, pseudo-symmetry of the ferrite (BCC) and martensite (BCT) phases prevents EBSD from accurately identifying all phases. Measuring the relative distortion of the crystal lattice, tetragonality, is one approach to identifying the phases. Unfortunately, small errors in the pattern center can cause significant errors in tetragonality measurement. Therefore, this research utilizes a new approach for accurate pattern center determination using a strain minimization routine and applies it to tetragonality maps for phase identification. Tetragonality maps based on dynamically simulated patterns result in the most accurate maps and can also be used to predict approximate local carbon content. Machine learning is then used on the collected data to isolate key attributes of RA grains and provide a decision tree model to predict transformation based on those attributes. Among the most relevant attributes found, RA grain area, RA grain shape aspect ratio, a “hardness” factor, and major axis orientation are included. Possible correlations between these factors and transformation improve understanding of relevant attributes and show the advantage that machine learning can have in unravelling complex material behavior.

L’évolution de la technologie microélectronique conduit à une densité d’intégration toujours plus forte des transistors. Les structures d’interconnexions en cuivre Damascène suivent cette tendance et doivent être maîtrisées en termes de fabrication, de performance et de robustesse, ces différents aspects étant intimement liés aux contraintes résiduelles et à la résistivité. Cette thèse vise à comprendre les mécanismes de génération de contraintes et identifier les différentes contributions à la résistivité de ces objets en fonction des conditions de recuit et des dimensions (de la centaine de nm à plusieurs µm). Pour ce faire, les rôles respectifs de la microstructure et des dimensions de films et de lignes de cuivre électrodéposés ont été découplés sur la base de modèles analytiques intégrants des paramètres microstructuraux et géométriques. La microstructure a été analysée principalement à partir de cartographies d’orientations cristallines réalisées par EBSD. Dans le cas des lignes de cuivre de 0.2 à 1 µm de large, les contraintes résiduelles ont été déduites de l’exploitation de nano-capteurs pivotants spécialement élaborés. Les résultats obtenus montrent qu’indépendamment de la température de recuit, l’augmentation de résistivité et de contraintes résiduelles observée vers les faibles dimensions est le fruit d’une diminution de la taille moyenne de cristallites et d’un confinement géométrique plus prononcé. En outre, l’augmentation de résistivité résulte également d’une élévation de la probabilité de réflexion des électrons aux joints de grains. Cette dernière a été associée à la réduction de la proportion de joints de grains spéciaux de cohérence atomique élevée. / The evolution of the microelectronic technology leads to a transistors integration density always stronger. The Damascene copper interconnections structures follow this tendency and must be controlled in terms of manufacturing, performance and robustness, these different aspects being intimately related to the residual stresses and resistivity. This thesis aims to understand the mechanisms of the residual stresses generation and identify the different contributions to the resistivity of these objects as a function of annealing conditions and dimensions (from about a hundred of nm to several µm). In order to do this, the respective effects of the microstructure and dimensions of electroplated copper films and lines were separated on the basis of analytical models integrating microstructural and geometrical parameters. The microstructure was principally analysed from mappings of crystalline orientations achieved by EBSD. For the copper lines of width 0.2 and 1 µm, the residual stresses were deduced from the exploitation of nano-rotating sensors specially elaborated. The results obtained show that independently of the annealing temperature, the resistivity and residual stresses increase observed toward the small dimensions arises from the diminution of the average crystallites size and the geometrical confinement more pronounced. Furthermore, the resistivity increase results also of the electrons reflection probability growth at grains boundaries. This last point was associated to the reduction of the proportion of special grains boundaries having a high atomic coherency.

Low temperature cleavage fracture behaviour was investigated using four experimental microalloyed bainitic plate steels. The four plate samples were produced by different thermomechanical processing (TMP) schedules and had yield strengths in the range 540 - 670 MPa. Microstructures were characterized by optical microscopy (OM), scanning electron microscopy (SEM) and electron back scattered diffraction (EBSD). Quantitative data was obtained for prior austenite grain (PAG) size, volume fractions of two bainite types (conventional bainite and acicular ferrite) and EBSD 15° domain size. Charpy impact tests (using two notch orientations) were carried out over a range of temperatures. Cleavage facet sizes were measured on -196°C Charpy samples. The range of TMP schedules produced variations in PAG width, type of bainite and 15° domain size. The effects of these three microstructural features on cleavage crack propagation are discussed. Results indicate that the microstructures are controlled by i) deformation below TNR and ii) accelerated cooling rate. Domain structure reflects TMP. There is no clear correlation between domain size and cleavage facet size. / Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2009-07-30 19:17:01.25

The design techniques of the components on the macro level are established in the scientific community, however are far behind from the real material performance limits. To obtain those limits, the deeper understanding of the material structure is required. The methods of a new comonents production through standard alloying are the basis of the modern material science manufacturing. The design of the materials with expected required performance limits is the next conceptual step for the materials scientist. As results, to make this step, the problem of a precise material structure analyses on the microstructural level is one os the major importance for the next generation materials design. The complexity of the material structure across the scales(macro-micro) requires a new non deterministic methods for better understanding of the connectivity betwen a materials performance and material microstructure features. This work presents a various new research methodologies and techniques of the material microstructure characterization and numerical design with future applications to the anlyses of the material behavior. The focus of the particular research was to analyse a new cross correlation function of the material structure on the micro length scale and develop a novel framework which allows a better understanding of various important material phenomenas such as failure initiation and recrystallization.

The majority of UK’s intermediate level radioactive waste is currently stored in 316L and 304L austenitic stainless steel containers in interim storage facilities for permanent disposal until a geological disposal facility has become available. The structural integrity of stainless steel canisters is required to persevere against environmental degradation for up to 500 years to assure a safe storage and disposal scheme. Hitherto existing severe localised corrosion observances on real waste storage containers after 10 years of exposure to an ambient atmosphere in an in-land warehouse in Culham at Oxfordshire, however, questioned the likelihood occurrence of stress corrosion cracking that may harm the canister’s functionality during long-term storage. The more corrosion resistant duplex stainless steel grade 2205, therefore, has been started to be manufactured as a replacement for the austenitic grades. Over decades, the threshold stress corrosion cracking temperature of austenitic stainless steels has been believed to be 50-60°C, but lab- and field-based research has shown that 304L and 316L may suffer from atmospheric stress corrosion cracking at ambient temperatures. Such an issue has not been reported to occur for the 2205 duplex steel, and its atmospheric stress corrosion cracking behaviour at low temperatures (40-50°C) has been sparsely studied which requires detailed investigations in this respect. Low temperature atmospheric stress corrosion cracking investigations on 2205 duplex stainless steel formed the framework of this PhD thesis with respect to the waste storage context. Long-term surface magnesium chloride deposition exposures at 50°C and 30% relative humidity for up to 15 months exhibited the occurrence of stress corrosion cracks, showing stress corrosion susceptibility of 2205 duplex stainless steel at 50°C.The amount of cold work increased the cracking susceptibility, with bending deformation being the most critical type of deformation mode among tensile and rolling type of cold work. The orientation of the microstructure deformation direction, i.e. whether the deformation occurred in transverse or rolling direction, played vital role in corrosion and cracking behaviour, as such that bending in transverse direction showed almost 3-times larger corrosion and stress corrosion cracking propensity. Welding simulation treatments by ageing processes at 750°C and 475°C exhibited substantial influences on the corrosion properties. It was shown that sensitisation ageing at 750°C can render the material enhanced susceptible to stress corrosion cracking at even low chloride deposition densities of ≤145 µm/cm². However, it could be shown that short-term heat treatments at 475°C can decrease corrosion and stress corrosion cracking susceptibility which may be used to improve the materials performance. Mechanistic understanding of stress corrosion cracking phenomena in light of a comprehensive microstructure characterisation was the main focus of this thesis.

Superaustenitická korozivzdorná ocel typu 22Cr25NiWCoCu určená pro vysokoteplotní aplikace v energetickém průmyslu byla studována za podmínek nízkocyklové únavy při pokojové a zvýšené teplotě. Jednotlivé vzorky byly podrobeny různým zátěžným procedurám, což umožnilo studium materiálové odezvy spolu s mechanismem poškození. Křivky cyklického zpevnění/změkčení, cyklického napětí a Coffin-Mansonovy křivky byly vyhodnoceny. Únavová životnost materiálu byla diskutována s ohledem na uplatňované mechanismy poškození, které se vyvinuly za specifických zátěžných podmínek. Standardní izotermální únavové experimenty byly provedeny při pokojové a zvýšené teplotě. Hysterezní smyčky zaznamenané během cyklického zatěžování byly analyzovány pomocí zobecněné statistické teorie hysterezní smyčky. Pro různé amplitudy napětí byla určena jak distribuce hustoty pravděpodobnosti interních kritických napětí (dále PDF), tak rovněž zjištěn její vývoj během cyklického namáhání. Zjištěné průběhy PDF byly korelovány s vývojem povrchového reliéfu a vnitřního dislokačního uspořádání zdokumentované pro obě teploty pomocí rastrovací elektronové mikroskopie (SEM) vybavené technikou fokusovaného iontového svazku (FIB), která umožnila rovněž efektivní studium nukleace povrchových únavových trhlin. Při cyklickém zatížení při pokojové teplotě byla pozorována lokalizace cyklické plastické deformace do perzistentních skluzových pásů (PSP). V místech, kde tyto PSP vystupují na povrch materiálu byly pozorovány perzistentní skluzové stopy (PSS) tvořené extruzemi a intruzemi. Postupné prohlubování intruzí, zejména na čele nejhlubší intruze, vede k iniciaci únavové trhliny. Odlišný mechanismus tvorby trhlin byl zjištěn při únavové zkoušce při zvýšené teplotě, kde zásadní roli hrál vliv prostředí. Rychlá oxidace hranic zrn a jejich následné popraskání představuje dominantní mechanismus v I. stádiu nukleace trhlin. Aplikace desetiminutové prodlevy v tahové části zátěžného cyklu vedlo k vývoji vnitřního (kavitačního) poškozování. Mechanismy vnitřního poškozování byly studovány na podélných řezech rovnoběžných s napěťovou osou zkušebních vzorků. Trhliny a jejich vztah k hranicím zrn a dvojčat byly studovány pomocí difrakce zpětně odražených elektronů (EBSD). Vliv prodlevy na únavovou životnost byl korelován s vývojem povrchového reliéfu a vnitřního poškození. Vzorky z uvedené oceli byly rovněž podrobeny zkouškám termomechanické únavy (TMF), při nichž se v čase mění jak zátěžná síla tak i teplota. Termomechanické únavové zkoušky v režimu soufázném (in-phase) a protifázném (out-of-phase) byly provedeny jak s prodlevou, tak i bez ní. Ve všech případech bylo pozorováno rychlé cyklické zpevnění bez ohledu na použitou amplitudu deformace, u vzorků testovaných v out-of-phase režimu byla zjištěna tendence k saturaci. Zkoumáním povrchového reliéfu za pomocí technik SEM a FIB byla odhalena přednostní oxidace hranic zrn a následné praskání těchto hranic kolmo k ose zatížení. Prodlevy v cyklech při maximálním napětí vedly ke zvýšení amplitudy plastické deformace a následně ke creepovému poškození ve formě vnitřních kavit a trhlin. Interkrystalické šíření trhlin bylo pozorováno na vzorcích testovaných v režimu in-phase. Vývoj poškození v režimu out-of-phase nebyl principiálně ovlivněn zařazením prodlevy do zátěžného cyklu. Charakteristickým znakem namáhání v režimu out-of-phase je nukleace několika trhlin v homogenní oxidické vrstvě jdoucích napříč zrny kolmo k ose zatěžování.