Geothermal heat exchangers are a growing energy technology that improve the energy efficiency of heating and cooling systems in buildings. Vertical borehole heat exchangers (BHE) coupled with ground source heat pumps have been widely developed and researched in the past century. The major disadvantage of BHEs is the initial capital cost required to drill the boreholes. Geothermal energy piles (GEP) were developed to help offset the high initial cost of these systems. A GEP combines ground source heat pump technology with deep earth structural foundations of buildings. GEPs are relatively new technology and robust standards and guidelines have not yet been developed for the design of these systems. The main operational difference between GEPs and conventional BHEs is the length and diameter of the below ground heat exchangers. The diameter of a GEP is much larger and the length is typically shorter than BHEs. Computational fluid dynamics (CFD) analysis is used in this study to investigate and better understand how structural piles perform as geothermal heat exchangers. The CFD analysis is used to simulate an existing experimental energy pile test. The experimental test is modeled as built including fluid modeling to provide additional detail into the behavior of the circulation fluid within the pile. Two comparisons of large diameter GEPs are made using CFD analysis to gain knowledge of the effects of varying pile diameter and loop configuration. The thermal response test was successfully modeled using the CFD model. The CFD results closely match the results of the field test. The large diameter comparisons show that the performance of an energy pile will increase as the diameter increases with a constant loop density. Multiple numbers of loops were tested in a constant diameter pile and the results show that with symmetrically placed loops the performance will increase with a greater number of loops in the pile. / Master of Science

Shallow geothermal energy (SGE) systems are becoming increasingly popular due to both their environmental and economic value. By using the ground as a source and sink for thermal energy, SGE systems are able to more efficiently heat and cool structures. However, their utility beyond structural heating and cooling is being realized as their applications now extend to slab and pavement heating, grain and agricultural drying, and swimming pool temperature control. Relatively recently, SGE systems have been combined with deep foundations to create a dual purpose element that can provide both structural support as well as thermal energy exchange with the subsurface. These thermo-active foundations provide the benefits of SGE systems without the additional installation costs. One of the novel applications of thermo-active foundations is in bridge deck deicing. Bridge decks experience two main winter weather related problems. The first of which is preferential icing, where the bridge freezes before the adjacent roadway because the bridge undergoes hastened energy loss due to its exposed nature. The second problem is the accelerated deterioration of concrete bridge decks resulting from the application of salts and other chemicals that are used to prevent accumulation and/or melt the frozen precipitation on roads and bridges. By utilizing the foundation of a bridge as a mechanism by which to access the shallow geothermal energy of the subsurface, energy can be supplied to the deck during the winter to melt and/or prevent frozen precipitation. An experimental ground-source bridge deck deicing system was constructed and the performance is discussed. Numerical models simulating the bridge deck and subsurface system components were also created and validated using the results from the numerical tests. Furthermore, the observed loads that result in a foundation from bridge deck deicing tests are shown. In order to better design for these loads, tools were developed that can predict the temperature change in the subsurface and foundation components during operation. Mechanisms by which to improve the efficiency of these systems without increasing the size of the borehole field were explored. Ultimately this research shows that SGE can effectively be used for bridge deck deicing. / Ph. D.

Geothermal energy has become a focal point of the renewable energy revolution. Both shallow and deep types of geothermal energy have the potential to offset carbon emissions, reduce energy costs, and stimulate the economy. Before widespread geothermal exploration and exploitation can occur, both shallow and deep technologies require improvement by theoretical and experimental investigations. This thesis investigated one aspect of both shallow and deep geothermal energy technologies. First, a group of shallow geothermal energy piles was modeled numerically. The model was constructed, calibrated, and validated using available data collected from full-scale in-situ experimental energy piles. Following calibration, the model was parameterized to demonstrate the impact of construction specifications on energy pile performance and cross-sectional thermal stress distribution. The model confirmed the role of evenly spaced heat exchangers in optimal pile performance. Second, experimental methods were used to demonstrate the evolution of a fractured granite permeability as a function of mineral dissolution. Steady-state flow-through experiments were performed on artificially fractured granite cores constrained by 5 MPa pore pressure, 30 MPa confining pressure, and a 120°C temperature. Upstream pore pressures, effluent mineral concentrations, and X-Ray tomography confirmed the hypothesis that fracture asperities dissolve during the flow through experiment, resulting in fracture closure.

Master of Science / Department of Civil Engineering / Dunja Peric / Piles have been used for many years in civil infrastructure as foundations for buildings, bridges, and retaining walls. Energy piles are thermo-active foundation systems that use geothermal energy for heating and cooling of buildings. Ground source heat is a very attractive, economical, efficient and sustainable alternative to current heating practices. Unlike the air temperature, the temperature below the Earth’s surface remains relatively constant throughout the year, somewhere between 10oC to 15oC below a depth of 6 m to 9 m (Kelly, 2011). This provides an opportunity for construction of thermo-active foundation systems with embedded geothermal loops. The main purpose of such thermo-active system is to transfer deep ground heat to a building through the fluid circulating within the geothermal loop. It is because these thermo-active foundation systems enable heat exchange between the deep ground and the building that is called the heat exchanger pile (HEP). The thermal energy supplied by a HEP can then supplement air-pump-based heating/cooling system. Although heat exchanger piles have been successfully implemented in Europe and Asia, their usage in U.S. remains uncommon. One reason for this might be currently limited understanding of the associated soil-structure interaction, thus unfavorably affecting the design procedures. To this end, a study was undertaken to investigate the predictive capabilities of computational models and to gain a better understanding of the load-transfer mechanisms of energy piles. Thus, coupled thermo-hydro-mechanical computational modeling of a single actual end bearing HEP was carried out for different loading scenarios including thermal and mechanical loads by using the finite element code ABAQUS/Standard 6.13-2. The results of the analyses of the heat exchanger pile with two different types of layered soil profile are presented: isotropic and anisotropic. The computational model was validated and verified successfully against field test results for all considered loading scenarios. Additional analyses were performed to gain a deeper insight into the effects of soil layering and on the behavior of energy piles. It was found that changes in the soil stiffness affected primarily the head displacement and vertical stresses and strains in the pile.

There has been an increasing interest in fundamental and applied research on emerging geotechnical and geoenvironmental engineering applications that pose multi-physics problems involving non-isothermal processes in unsaturated soils. Properly studying these problems requires the development of analytical models to describe the constitutive behavior of unsaturated soils under non-isothermal conditions. However, major gaps remain in the development of unified models that can properly represent the temperature dependency of unsaturated soil behavior. The effects of temperature on the stability of slopes, lateral earth pressure, and pile resistance in unsaturated soils are also not well understood. The main objective of this study is to provide new insight and robust tools to characterize and model the temperature-dependent behavior of unsaturated soils. For this purpose, novel unified models are developed for soil water retention curve, effective stress, thermal conductivity function, and small-strain shear modulus for unsaturated soils at elevated temperatures. The models are proposed by establishing or extending the unified model at isothermal conditions to nonisothermal conditions. The fundamental and main variable in all unified models is capillary pressure (also referred to as matric suction). The effect of temperature is considered on adsorption and capillarity as a function of water-air surface tension, soil-water contact angle, and enthalpy of immersion. The proposed models are verified by comparing them with experimental data reported in the literature and measurements made in this study. Overall results of the proposed models show an excellent predictive capability. Furthermore, the parametric study is conducted to understand the effect of different parameters such as soil type, temperature, drainage conditions, and among others on hydraulic and mechanical properties of unsaturated soil. Finally, the proposed models are incorporated into geotechnical applications such as slope stability, lateral earth pressure, and pile resistance involving unsaturated conditions and elevated temperatures. The variation of temperature in unsaturated soils for these applications can be notable and cannot be ignored in the design and analysis. The proposed formulations can also be readily incorporated into analytical solutions and numerical simulations of thermo-hydro-mechanical processes in unsaturated soils. The findings of the study can facilitate using numerical models to simulate various non-isothermal applications including geo-energy systems and soil-atmospheric interaction problems.

Yes / This study aims to evaluate the impacts of using thermally enhanced concrete on the thermal performance of geoenergy structures and interaction between the thermo-active-structures and adjacent dry and partly saturated soils. Experiments using a fully instrumented testing rig were carried out on prototypes of energy pile and diaphragm wall made from normal concrete and thermally enhanced concrete by the addition of graphTHERM powder. Results illustrated that adding 36% of graphTHERM powder to the concrete by weight of cement was found to double the thermal conductivity of concrete and improve the stiffness by 15% without detrimental effects on the compressive strength. The heat transfer efficiency of energy pile and energy diaphragm wall made from thermally enhanced concrete was significantly improved by 50% and 66% respectively, in comparison with the efficiency of the same type of energy structure that was made from a typical normal concrete.

Energy piles are deep foundation elements designed to utilize near-surface geothermal energy, while at the same time serve as foundations for buildings. The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their thermo-mechanical behavior. The change in temperature along energy piles, resulting from their employment in heat exchange operations, causes axial displacements, thermally induced axial stresses and changes in mobilized shaft resistance which may have possible effects on their behavior. In order to investigate these effects, an extensive field test program, including conventional pile load tests and application of heating-cooling cycles was conducted on three energy piles during a period of six weeks. Temperature changes were applied to the test piles with and without maintained mechanical loads to investigate the effects of structural loads on energy piles. Moreover, the lengths of the test piles were determined to represent different end-restraining conditions at the toe. Various sensors were installed to monitor the strain and temperature changes along the test piles. Axial stress and shaft resistance profiles inferred from the field test data along with the driven conclusions are presented herein for all three test piles. It is inferred from the field test results that changes in temperature results in thermally induced compressive or tensile axial stresses along energy piles, the magnitude of which increases with higher restrictions such as structural load on top or higher toe resistance. Moreover, lower change in shaft resistance is observed with increasing restrictions along the energy piles. In addition to the design, deployment, and execution of the field test, a thermo-mechanical cyclic numerical model was developed as a part of this research. In this numerical model, load-transfer approach was coupled with the Masing's Rule in order to simulate the two-way cyclic axial displacement of energy piles during temperature changes. The numerical model was validated using the field test results for cyclic thermal load and thermo-mechanical load applications. It is concluded that the use of load-transfer approach coupled with the Masing's Rule is capable of simulating the cyclic thermo-mechanical behavior of energy piles. / Ph. D. / Global energy demands are increasing rapidly, along with depleting natural resources. Of equal importance, the consumption of fossil fuels pose a great threat to the environment. Hence, there is an urgent need to find alternative energy resources, such as near surface geothermal energy. Energy piles are one of the ways of exploiting near surface geothermal energy. In this system, the piles that are already required for structural support are equipped with geothermal loops, for heat exchange operations. With the use of energy piles, the heat energy can be extracted from the ground to heat the buildings during winter. Similarly, the heat energy can be withdrawn into the ground, in order to cool the buildings during summer. Energy piles provide an environmental friendly way of heating and cooling of the buildings. However, there are several effects of the heat exchange operations on the behavior of energy piles. During winter, because of heat extraction, the temperature of the energy pile decreases, which causes the tendency of contraction of the pile. On the other hand, during summer, the heat injection into the ground increases the temperature of the energy piles, which results in a tendency of elongation of the energy pile. Depending on the level of restriction from the surrounding soil or the building on top, some of the expansion or contraction tendency of the energy piles actually take place, which results in axial displacements and changes in shaft resistance. The restricted part of the contraction or expansion causes axial stresses along the piles. The primary role of the piles, which is structural support, should not be jeopardized by these effects of heat exchange operations. In this doctoral research, the effects of temperature change on the behavior of energy piles are investigated. For the experimental investigation, a full-scale field test on three energy piles was performed, where temperature changes were applied to the test piles, to evaluate their effects. In addition, a numerical model was developed, and it is validated by using the field test results. This numerical model can be used for different soil profiles, pile characteristics and temperature changes, in order to estimate the behavior of various scenarios of energy piles during their design.

L'efficacité de pieux géothermiques (e.g. énergétiques) a été examinée et validée par de nombreuses études à partir de points de vue environnemental et énergétique jusqu'à présent. Néanmoins, la technologie des pieux géothermiques est encore peu connue et rarement appliquée dans la construction, notamment en France comparée à d'autres pays européens. La raison principale du manque d'attention peut être la connaissance limitée sur les impacts du chargement thermomécanique sur le comportement du pieu et celui du sol environnant. Cette thèse vise à étudier les aspects géotechniques des pieux géothermiques grâce aux modélisations physiques et numériques. Un modèle physique est développé afin de mieux connaitre l'interaction sol/pieu sous chargement thermomécanique. Le modèle est composé d'un pieu énergétique équipé des tubes d'échangeur de chaleur, installé dans un sol compacté. Le pieu a d'abord été installé dans un sable sec, puis dans une argile saturée ; il a ensuite été chargé mécaniquement et soumis à des cycles thermiques. L'effet de la charge mécanique, du nombre de cycles thermiques et du type de sol a été étudié. Les résultats montrent la génération de tassements irréversibles au cours des cycles thermiques, dont la quantité augmente avec l'augmentation de la charge en têtes du pieu. La pression totale dans le sol à proximité de la surface du pieu ne change pas par refroidissement et chauffage, tandis que la pression totale au-dessous du pieu augmente progressivement à mesure que les cycles thermiques poursuivent. Les expériences montrent aussi l'évolution des profils de la force axiale avec la température ; la force axiale dans le pieu augmente pendant le refroidissement et diminue pendant l'échauffement. Les comportements au cisaillement du sol (mêmes sols que ceux utilisés dans la première partie) ainsi que de l'interface sol/béton ont été évalués à différentes températures. Pour ce faire, un appareil de cisaillement conventionnel a été équipé d'un système de contrôle de température. Le sol (et l'interface sol/béton) a été soumis à une gamme de contraintes relativement faibles. La consolidation thermique a été effectuée selon un protocole particulier. Il a été observé que l'angle de frottement et la cohésion de matériaux utilisés ne changent pas sensiblement avec température. L'étude numérique a débuté par la simulation d'essais existants dans la littérature sur des pieux énergétiques en appliquant une méthode simplifiée via un code de calcul basé sur la méthode des éléments finis et assez répandu dans la profession. Le changement de la température est simulé en imposant au pieu des déformations volumétriques calculées à partir du coefficient de dilatation thermique du matériau. La méthode prédit correctement le comportement de certains pieux énergétiques à grande échelle en termes de contrainte axiale et de déplacement en tête du pieu. Les résultats mettent en évidence le rôle important joué par le changement de volume du pieu induit par les variations thermiques sur son comportement mécanique. Dans un second temps, un autre code de calcul offrant la possibilité d'inclure les effets thermique a été utilisé pour la modélisation des essais effectués auparavant sur le modèle physique. Ainsi, en comparant aux modélisations numériques précédemment expliquées, le changement de volume du sol induit par les variations de température est également pris en compte. Les résultats numériques et expérimentaux sont ainsi comparés. On en déduit que le modèle numérique est capable de prédire le comportement des pieux sous chargement purement mécanique. En outre, en simulant des essais thermomécaniques, une bonne estimation du transfert thermique dans le sol est obtenue. En ce qui concerne le comportement mécanique du pieu au cours de cycles thermiques, le modèle numérique prédit bien le tassement progressif du pieu. Cependant, en termes de répartition de la force axiale, on obtient des résultats contradictoires / Energy pile efficiency has been tested and validated by numerous studies from environmental and energy-related points of view until now. Nevertheless, energy pile technology is still more or less unknown and rarely applied in construction, especially in France compared to other European countries. The chief reason for this lack of attention might be the limited knowledge of the impact of the coupled thermo-mechanical loading on the behaviour of the pile and that of the surrounding soil. This thesis aims to study the geotechnical aspects of energy piles through physical modelling and some numerical investigations. A physical model is developed in order to better identify the soil/pile interaction under thermo-mechanical loading. The model is made up of a small pile equiped with a heat exchanger loop embedded in compacted soil. The pile was once installed in dry sand and then in saturated clay; it was then loaded mechanically and was subjected to thermal cycles. The effect of mechanical load value, number of thermal cycles and soil type is studied. The results show the appearance of irreversible settlements during thermal cycles, whose quantity increases as the pile head load increases. Total pressure in the soil close to the pile surface does not change by cooling and heating, while total pressure below the pile increases gradually as thermal cycles proceed. This is in accordance with the permanent downward movement of the pile within thermal cycles. Experiments also show the evolution of axial force profiles with temperature, axial force in the pile increases by cooling and decreases by heating. In another part of the experimental work, we focused on the soil/pile interface. The shear behaviour of the soil (the same as the soils used above) and that of the soil/concrete interface was evaluated at different temperatures. To do this, a conventional shear apparatus was equipped with a temperature control system. Soil (and soil/concrete interface) was subjected to a rather low range of stress. Thermal consolidation was performed according to a special protocol. It was observed that the soil friction angle and cohesion do not change considerably relative to temperature. The numerical study was initiated by simulating existing tests in the literature on energy piles through a finite element code well-known to engineers, applying a simplified method. The thermal load was simulated by imposing volumetric strains calculated from the coefficient of thermal expansion of the material on the pile. The method successfully simulates the behaviour of some full-scale energy piles in terms of axial strain and pile head displacement. The results highlight the important role played by the pile thermal volume change on the mechanical behaviour of the energy pile under various thermo-mechanical loadings. In the second stage, another numerical code with the possibility of including temperature effects was used for modelling the tests formerly performed on the physical model. Thus, compared to the first numerical attempts, the soil thermal volume change is also taken into account. The numerical results were compared with the experimental ones obtained from physical modelling. It was deduced that the numerical model could simulate correctly the pile behaviour under purely mechanical loading. Also, simulating thermo-mechanical tests, a good estimation of heat conduction in the soil was achieved numerically. Regarding the mechanical behaviour of the pile under thermal cycles, the numerical model adequately predicts the gradual ratcheting of the pile as observed in the experiments. However in terms of axial force distribution in the pile, the results from numerical modelling are different from the physical one

Diploma thesis deals with geothermal foundations. The aim of the thesis is to find optimal way of pipe winding for heat-carrying liquid in foundation piles. The problem is solved by CFD simulations in ANSYS Fluent. Determinative parameters like the pressure loss, heat fluxes and U-value in one pile circuit with two ways of pipe installations – Single coil, where reverse pipe is led in the middle of pile and Duplex Coil with reverse pipe in spiral shape are observed.