No description available.

Wood pellets are offering opportunities for a cleaner-burning biofuel but major concerns are overshadowing their potential. Tony Bi and UBC’s Clean Energy Research Centre are engineering solutions.

The objective of this research is to build a decision model for a comprehensive assessment of solar photovoltaic technologies using multiple perspectives. These perspectives include: social, technological, economic, environmental, and political (STEEP) with each perspective consisting of multiple criteria. Hierarchical decision modeling and expert judgment quantification are used to provide the relative ranking of the perspectives and criteria. Such modeling is effective in addressing technology evaluations with competing and contrasting perspectives and criteria where both quantitative and qualitative measurements are represented. The model is then operationalized by constructing desirability functions for each criterion. The combined results provide an overall numerical score for each technology under consideration as well as criteria desirability gaps. This model is useful for assessing photovoltaic technologies from varying worldviews such as the electric utility worldview, the photovoltaic manufacturer's worldview, or the national policy worldview. This model can also provide guidance to decision makers and practitioners on areas of improvement for a selected technology. The research utilizes the electric utility worldview as a case study.

The needs to the sustainable development of electricity, energy efficiency improvement, and environment pollution reduction have favored the development of distributed generation (DG). But the problems come with increasing DG penetration in distribution networks. This thesis presents the Solar Energy Grid Integration System (SEGIS) Stage III project done by Portland General Electric (PGE), Advanced Energy, Sandia National Lab on a PGE selected distribution feeder. The feeder has six monitored commercial solar PV systems connected. The total power output from the PV systems has the potential to reach 30% of the feeder load. The author analyzes the performance of the solar feeder on both generation and voltage effects. As a project report, it introduced a new islanding detection done by other team members to give an islanding solution of future high penetration distribution networks. At last, the author describes micro-grid and grid support concepts in a SEGIS concept paper with some examples.

No description available.

Indiana University-Purdue University Indianapolis (IUPUI) / The existing topologies of solar micro inverter use a number of stages before the DC input voltage can be converted to AC output voltage. These stages may contain one or more power converters. It may also contain a diode rectifier, transformer and filter. The number of active and passive components is very high. In this thesis, the design of a new solar micro inverter is proposed. This new micro inverter consists of a new single switch inverter which is obtained by modifying the already existing single ended primary inductor (SEPIC) DC-DC converter. This new inverter is capable of generating pure sinusoidal waveform from DC input voltage. The design and operation of the new inverter are studied in detail. This new inverter works with a controller to produce any kind of output waveform. The inverter is found to have four different modes of operation. The new inverter is modeled using state space averaging. The system is a fourth order system which is non-linear due to the inherent switching involved in the circuit. The system is linearized around an operating point to study the system as a linear system. The control to output transfer function of the inverter is found to be non-minimum phase. The transfer functions are studied using root locus. From the control perspective, the presence of right half zero makes the design of the controller structure complicated. The PV cell is modeled using the cell equations in MATLAB. A maximum power point tracking (MPPT) technique is implemented to make sure the output power of the PV cell is always maximum which allows full utilization of the power from the PV cell. The perturb and observe (P&O) algorithm is the simplest and is used here. The use of this new inverter eliminates the various stages involved in the conventional solar micro inverter. Simulation and experimental results carried out on the setup validate the proposed structure of inverter.

Indiana University-Purdue University Indianapolis (IUPUI) / Instrument assisted soft tissue mobilization (IASTM) is a form of massage using rigid manufactured or cast devices. The delivered force, which is a critical parameter in massage during IASTM, has not been measured or standardized for most clinical practices. In addition to the force, the angle of treatment and frequency play an important role during IASTM. As a result, there is a strong need to characterize the delivered force to a patient, angle of treatment, and stroke frequency. This thesis proposes two novel mechatronic designs for a specific instrument from Graston Technique(Model GT3), which is a frequently used tool to clinically deliver localize pressure to the soft tissue. The first design is based on compression load cells, where 4-load cells are used to measure the force components in three-dimensional space. The second design uses a 3D load cell, which can measure all three force components force simultaneously. Both designs are implemented with IMUduino microcontroller chips which can also measure tool orientation angles and provide computed stroke frequency. Both designs, which were created using Creo CAD platform, were also analyzed thorough strength and integrity using the finite element analysis package ANSYS. Once the static analysis was completed, a dynamic model was created for the first design to simulate IASTM practice using the GT-3 tool. The deformation and stress on skin were measured after applying force with the GT-3 tool. Additionally, the relationship between skin stress and the load cell measurements has been investigated. The second design of the mechatronic IASTM tool was validated for force measurements using an electronic plate scale that provided the baseline force values to compare with the applied force values measured by the tool. The load cell measurements and the scale readings were found to be in agreement within the expected degree of accuracy. The stroke frequency was computed using the force data and determining the peaks during force application. The orientation angles were obtained from the built-in sensors in the microchip.

Active layer morphology of polymer-based solar cells plays an important role in improving power conversion efficiency (PCE). In this thesis, the focus is to improve the device efficiency of polymer-based solar cells. In the first objective, active layer morphology of polymer-solar cells was optimized though a novel solvent annealing technique. The second objective was to explore the possibility of replacing the highly sensitive aluminum cathode layer with a low-cost and stable alternative, copper metal. Large scale manufacturing of these solar cells is also explored using roll-to-roll printing techniques. Poly (3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl (PCBM) were used as the active layer blend for fabricating the solar cell devices using bulk heterojunction (BHJ), which is a blend of a donor polymer and an acceptor material. Blends of the donor polymer, P3HT and acceptor, PCBM were cast using spin coating and the resulting active layers were solvent annealed with dichlorobenzene in an inert atmosphere. Solvent annealed devices showed improved morphology with nano-phase segregation revealed by atomic force microscopy (AFM) analysis. The roughness of the active layer was found to be 6.5 nm. The nano-phase segregation was attributed to PCBM clusters and P3HT domains being arranged under the solvent annealing conditions. These test devices showed PCE up to 9.2 % with current density of 32.32 mA/cm2, which is the highest PCE reported to date for a P3HT-PCBM based system. Copper was deposited instead of the traditional aluminum for device fabrication. We were able to achieve similar PCEs with copper-based devices. Conductivity measurements were done on thermally deposited copper films using the two-probe method. Further, for these two configurations, PCE and other photovoltaic parameters were compared. Finally, we studied new techniques of large scale fabrication such as ultrasonic spray coating, screen-printing, and intense pulse light sintering, using the facilities at the Conn Center for Renewable Energy Research at the University of Louisville. In this study, prototype devices were fabricated on flexible ITO coated plastics. Sintering greatly improved the conductivity of the copper nano-ink cathode layer. We will explore this technique’s application to large-scale fabrication of solar cell devices in the future work.