In this thesis, the potential of enhanced geothermal system to provide adequate energy to a 10 MW electricity power plant from Prairie Evaporite Formation of Williston Basin was investigated. This formation partly consists of halite with low thermal resistance and high thermal conductivity, which translates into a lower drilling length to reach the desired temperature, comparing to other rock types. To this end, two numerical models with experimental data in south-west Manitoba (i.e. Tilston) and south-east Saskatchewan (i.e. Generic) were designed. The thermal reservoirs were located at 1.5 km (Tilston site) and 3 km (Generic site) with approximate thicknesses of 118 m. Considering an injection brine of 6% NaCl at 15°C, the final derived temperature at wellhead of the production wells were 43°C and 105°C respectively. Finally, the Generic site was concluded as a suitable candidate for electricity production by providing higher surfaced fluid temperature than the minimum of 80°C. / February 2017

The present work addresses the thermodynamic optimization of small binary-cycle geothermal power plants. The optimization process and entropy generation minimization analysis were performed to minimize the overall exergy loss of the power plant, and the irreversibilities associated with heat transfer and fluid friction caused by the system components. The effect of the geothermal resource temperature to impact on the cycle power output was studied, and it was found that the maximum cycle power output increases exponentially with the geothermal resource temperature. In addition, an optimal turbine inlet temperature was determined, and observed to increase almost linearly with the increase in the geothermal heat source. Furthermore, a coaxial geothermal heat exchanger was modeled and sized for minimum pumping power and maximum extracted heat energy. The geofluid circulation flow rate was also optimized, subject to a nearly linear increase in geothermal gradient. In both limits of the fully turbulent and laminar fully-developed flows, a nearly identical diameter ratio of the coaxial pipes was determined irrespective of the flow regime, whereas the optimal geofluid mass flow rate increased exponentially with the Reynolds number. SeveORCs were observed to yield maximum cycle power output. The addition of an IHE and/or an Oral organic Rankine Cycles were also considered as part of the study. The basic types of the FOH improved significantly the effectiveness of the conversion of the available geothermal energy into useful work, and increased the thermal efficiency of the geothermal power plant. Therefore, the regenerative ORCs were preferred for high-grade geothermal heat. In addition, a performance analysis of several organic fluids was conducted under saturation temperature and subcritical pressure operating conditions of the turbine. Organic fluids with higher boiling point temperature, such as n-pentane, were recommended for the basic type of ORCs, whereas those with lower vapour specific heat capacity, such as butane, were more suitable for the regenerative ORCs. / Dissertation (MEng)--University of Pretoria, 2013. / Mechanical and Aeronautical Engineering / unrestricted

In geothermal reservoirs and unconventional gas reservoirs with very low matrix permeability, fractures are the main routes of fluid flow and heat transport, so the fracture permeability change is important. In fact, reservoir development under this circumstance relies on generation and stimulation of a fracture network. This thesis presents numerical simulation of the response of a fractured rock to injection and extraction considering the role of poro-thermoelasticity and joint deformation. Fluid flow and heat transport in the fracture are treated using a finite difference method while the fracture and rock matrix deformation are determined using the displacement discontinuity method (DDM). The fractures response to fluid injection and extraction is affected both by the induced stresses as well as by the initial far-field stress. The latter is accounted for using the non-equilibrium condition, i.e., relaxing the assumption that the rock joints are in equilibrium with the in-situ stress state. The fully coupled DDM simulation has been used to carry out several case studies to model the fracture response under different injection/extractions, in-situ stresses, joint geometries and properties, for both equilibrium and non-equilibrium conditions. The following observations are made: i) Fluid injection increases the pressure causing the joint to open. For non-isothermal injection, cooling increases the fracture aperture drastically by inducing tensile stresses. Higher fracture aperture means higher conductivity. ii) In a single fracture under constant anisotropic in-situ stress (non-equilibrium condition), permanent shear slip is encountered on all fracture segments when the shear strength is overcome by shear stress in response to fluid injection. With cooling operation, the fracture segments in the vicinity of the injection point are opened due to cooling-induced tensile stress and injection pressure, and all the fracture segments experience slip. iii) Fluid pressure in fractures increases in response to compression. The fluid compressibility and joint stiffness play a role. iv) When there are injection and extraction in fractured reservoirs, the cooler fluid flows through the fracture channels from the injection point to extraction well extracting heat from the warmer reservoir matrix. As the matrix cools, the resulting thermal stress increases the fracture apertures and thus increases the fracture conductivity. v) Injection decreases the amount of effective stress due to pressure increase in fracture and matrix near a well. In contrast, extraction increases the amount of effective stress due to pressure drop in fracture and matrix.

Multistage hydraulic fracturing of horizontal wells continues to be a major technological tool in the oil and gas industry. Creation of multiple transverse fractures in shale gas has enabled production from very low permeability. The strategy entails the development of a Stimulated Reservoir Volume (SRV), defined as the volume of reservoir, which is effectively stimulated to increase the well performance. An ideal model for a shale gas SRV is a rectangle of length equal to horizontal well length and width equal to twice the half length of the created hydraulic fractures. This project focused on using the Multistage Transverse Fractured Horizontal Wells (MTFHW) for two novel applications. The first application considers using the SRV of a shale gas well, after the gas production rate drops below the economic limit, for low grade geothermal heat extraction. Cold water is pumped into the fracture network through one horizontal well drilled at the fracture tips. Heat is transferred to the water through the fracture surface. The hot water is then recovered through a second horizontal well drilled at the other end of the fracture network. The basis of this concept is to use the already created stimulated reservoir volume for heat transfer purposes. This technique was applied to the SRV of Haynesville Shale and the results were discussed in light of the economics of the project. For the second application, we considered the use of a similarly created SRV for producing hydrocarbon products from oil shale. Thermal decomposition of kerogen to oil and gas requires heating the oil shale to 700 degrees F. High quality saturated steam generated using a small scale nuclear plant was used for heating the formation to the necessary temperature. Analytical and numerical models are developed for modeling heat transfer in a single fracture unit of MTFHW. These models suggest that successful reuse of Haynesville Shale gas production wells for low grade geothermal heat extraction and the project appears feasible both technically and economically. The economics of the project is greatly aided by eliminating well drilling and completion costs. The models also demonstrate the success of using MTFHW array for heating oil shale using SMR technology.

Cette recherche vise à étudier les impacts environnementaux d'une technologie émergente de production d’électricité basée sur une source renouvelable, les systèmes géothermiques stimulés (EGS), par l’analyse de leur cycle de vie (ACV).Après avoir analysé plusieurs études de cas, nous avons développé un modèle ACV paramétré capable de caractériser les performances environnementales de la filière EGS. Nos résultats montrent que les émissions de gaz à effet de serre des EGS sur leur cycle de vie sont bien inférieures à celles des centrales utilisant des combustibles fossiles.Dans un deuxième temps, nous avons mis au point un cadre méthodologique pour appliquer l'analyse de sensibilité globale (GSA) à l’ACV des technologies émergentes comme les EGS, prenant en compte les incertitudes élevées liées à leur caractère innovant. Nous avons appliqué notre nouvelle approche GSA pour développer un modèle ACV simplifié, à destination des décideurs, permettant une estimation rapide des impacts des EGS à partir de seulement cinq paramètres clefs: capacité installée, profondeur de forage, nombre de puits, débit géothermal et durée de vie.L'approche méthodologique développée dans cette thèse est applicable à d'autres technologies et ouvre de larges perspectives de recherche dans le domaine de l'évaluation environnementale. / This thesis investigates the environmental impacts of an emerging renewable energy technology, the enhanced geothermal systems (EGS), using a life cycle assessment (LCA) approach.Following the analysis of several EGS case studies, we developed a parameterized LCA model able to provide a global overview of the life cycle impacts of the EGS technology. The greenhouse gas emissions of EGS are found comparable with other renewable energy systems and far better than those of power plants based on fossil fuels.In a second stage, we developed a methodological framework for the application of global sensitivity analysis (GSA) to the LCA of emerging technologies like the EGS, taking into account the high uncertainties related to their description. We applied our new GSA approach to generate a simplified LCA model, aimed at decision makers, allowing a rapid estimation of the life cycle impacts of EGS from only five key parameters: installed capacity, drilling depth, number of wells, flow rate and lifetime.The methodological approach developed in this thesis is applicable to other technologies and opens large research perspectives in the field of environmental assessment.