No description available.

Friction Bit Joining (FBJ) is a new technology used primarily in joining dissimilar metals. Its primary use has been focused in the automotive industry to provide an alternative joining process to welding. As automotive manufacturing has continually pushed toward using dissimilar materials, new joining processes have been needed to replace traditional welding practices that do not perform well when materials are not weld compatible. FBJ meets these needs perfectly as it provides strength as well as the ability to join materials of almost any kind.The purpose of this research was to explore different applications of the FBJ process. Traditionally FBJ has used a steel bit to drill through a thin piece of aluminum and weld to a piece of steel behind the aluminum. This research explored a different application of FBJ by using a steel bit to drill through multiple pieces of aluminum and weld to a small steel bit on the backside of the aluminum. The primary goal of this research was to answer two questions. (1) How does drilling impact peak weld strength and (2) Does an optimal shank diameter exist in terms of peak weld strength? As in other research, no universal parameters were found for optimization of lap shear, cross tension and t-peel tests. Drilling was found to be an important factor in peak weld strength. Number of flutes on the consumable steel bit was varied to see the impact of better and worse chip clearance ability. Increasing number of flutes was found to positively impact peak weld strength to a point. Optimal number of flutes was found to be different for each type of testing. It was found that there was an optimal bit head to bit shank diameter ratio that optimized peak weld strength. Again the optimal diameter was different for each test. Bits of different diameters were created and then tested to measure the impact of varying shank diameters on peak weld strength. It was found that there was a strength tradeoff between two localized joint areas in diameter testing. Decreasing the shank diameter increased the amount of overlap formed by the bit head over the top coupon. This shifted strength to the bit head region. While this strengthened the bit head region of the joint, strength was sacrificed in the bit-nut intersection. This tradeoff was consistently found in all test types.

Friction Bit Joining (FBJ) is a new technology used primarily in joining dissimilar metals. Its primary use has been focused in the automotive industry to provide an alternative joining process to welding. As automotive manufacturing has continually pushed toward using dissimilar materials, new joining processes have been needed to replace traditional welding practices that do not perform well when materials are not weld compatible. FBJ meets these needs perfectly as it provides strength as well as the ability to join materials of almost any kind.The purpose of this research was to explore different applications of the FBJ process. Traditionally FBJ has used a steel bit to drill through a thin piece of aluminum and weld to a piece of steel behind the aluminum. This research explored a different application of FBJ by using a steel bit to drill through multiple pieces of aluminum and weld to a small steel bit on the backside of the aluminum. The primary goal of this research was to answer two questions. (1) How does drilling impact peak weld strength and (2) Does an optimal shank diameter exist in terms of peak weld strength? As in other research, no universal parameters were found for optimization of lap shear, cross tension and t-peel tests. Drilling was found to be an important factor in peak weld strength. Number of flutes on the consumable steel bit was varied to see the impact of better and worse chip clearance ability. Increasing number of flutes was found to positively impact peak weld strength to a point. Optimal number of flutes was found to be different for each type of testing. It was found that there was an optimal bit head to bit shank diameter ratio that optimized peak weld strength. Again the optimal diameter was different for each test. Bits of different diameters were created and then tested to measure the impact of varying shank diameters on peak weld strength. It was found that there was a strength tradeoff between two localized joint areas in diameter testing. Decreasing the shank diameter increased the amount of overlap formed by the bit head over the top coupon. This shifted strength to the bit head region. While this strengthened the bit head region of the joint, strength was sacrificed in the bit-nut intersection. This tradeoff was consistently found in all test types.

Friction Bit Joining (FBJ) is a new technology that can be used to join dissimilar materials together. This ability makes it a good candidate for creating light weight structures for the automotive industry by combining lightweight materials such as aluminum to stronger materials like advanced high-strength steels. The automotive industry and many other industries have great interest in reducing structure weight to increase fuel efficiency. The purpose of this research is to make FBJ of GADP 1180 to AA 7085-T76 a production ready process by (1) better understanding the effects of process parameters, bit design and tool design on joint strength and reliability especially as they relate to different joint configurations; (2) determining if consecutive FBJ joints on a part will be additive in strength; (3) improving surface finish for better coating adhesion so that joints can be made to withstand extended corrosion testing; and (4) determining the failure modes and fatigue life of joint components at high and low load amplitudes. No universal parameter set for optimizing peak load for T-peel, cross tension, and lap-shear tension configurations were found. Due to the extreme load conditions of T-peel and the smaller margin of safety it is better to optimize for T-peel. However, strength and reliability were still improved across the board. Cutting features and tapered shanks were found to not always be necessary. Removing cutting features from the bit design increased peak weld cycle loads, but a stiffer machine can overcome this. Consecutive FBJ joints on a part are mostly additive in nature. When the weakest joint fails, its load is distributed to the remaining joints and will limit the peak load of the whole part. If all joints are "good" then the peak load will be approximately additive. Most of the stress is localized on the side of the bit opposite of the pulling direction. Failure modes in lap-shear tend to change from weld nugget pullouts in single weld specimens to aluminum material failures in multi-weld specimens. This is because of the added stiffness that additional material and welds provide to resist coupons bending and creating a peeling action. Surface finish was improved by development of a floating carbide cutting system which cut aluminum flash as it was generated around the head of the bit. A new internal drive design provided the ability to drive bits flush with the aluminum top layer if desired with minimal reductions in strength. Flush bits provided benefits in safety, cosmetics, and coating adhesion.

Friction Bit Joining (FBJ) is a new technology that allows lightweight metals to be joined to advanced high-strength steels (AHSS). Joining of dissimilar metals is especially beneficial to the automotive industry because of the desire to use materials such as aluminum and AHSS in order to reduce weight and increase fuel efficiency. In this study, FBJ was used to join 7075 aluminum and DP980 ultra-high-strength steel. FBJ is a two-stage process using a consumable bit. In the first stage, the bit cuts through the top material (aluminum), and in the second stage the bit is friction welded to the base material (steel). The purpose of the research was to examine the impact a solid head bit design would have on joint strength, manufacturability, and ease of automation. The solid head design was driven externally. This design was compared to a previous internally driven head design. Joint strength was assessed according to an automotive standard established by Honda. Joints were mechanically tested in lap-shear tension, cross-tension, and peel configurations. Joints were also fatigue tested, cycling between loads of 100 N and 750 N. The failure modes that joints could experience during testing include: head, nugget, material, or interfacial failure. All tested specimens in this research experienced interfacial failure. Welds were also created and examined under a microscope in order to validate a simulation model of the FBJ process. The simulation model predicted a similar weld shape and bond length with 5 percent accuracy. Joints made with external bits demonstrated comparable joint strength to internal bits in lap-shear tension and cross-tension testing. Only external bits were tested after lap-shear tension, because it was determined that external bits would perform comparably to internal bits. Joints made with external bits also exceeded the standard for failure during fatigue testing. Peel tested specimens did not meet the required strength for the automotive standard. Examining specimens under a microscope revealed micro-cracks in the weld. These defects have been shown to decrease joint strength. Joint strength, especially during peel testing, could be increased by reducing the presence of micro-cracks. The external bit design is an improvement from the internal bits for manufacturability and ability to be automated, because of the less-expensive processes used to form the bit heads and the design that lends to ease of alignment.

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, plunge speed, cutting and welding depths, and dwell times. It was determined that, when using 1.6 mm thick coupons, maximum joint strengths would be obtained at a 2.03 mm cutting depth, 3.30 mm welding depth, and 2500 RPM welding speed. At these levels, the weld is stronger than the magnesium alloy, resulting in failure in the AZ31 rather than in the FBJ joint in lap shear testing.

Friction Bit Joining (FBJ) is a new technology that can be used to join dissimilar materials together. This ability makes it a good candidate for creating lightweight structures for the automotive industry by combining lightweight materials such as aluminum to stronger materials like advanced high-strength steels. The automotive industry is putting significant effort into interest in reducing vehicle structure weight to increase fuel efficiency and reduce greenhouse gas emissions. Joining of dissimilar materials is a challenge they face in the light weighting the body of the vehicle. The purpose of the current research is to employ FBJ in the joining of a very challenging material combination: GA DP 1180 to AA 7085-T71. In accomplishing this purpose, the goal is to move FBJ toward a more production ready process by better understanding the effects of tooling, bit design, and process parameters on joint strength and reliability as they relate to load profiles captured during the joining process. It was found that the joint strength variation was influenced strongly by the hardness and the geometric consistency of the consumable bits. Bit hardness below 45 HRC led to joint strength that was less than the required specification (5kN in lap shear tension, and 1.5kN in cross-tension and T-peel). Variation in bit height and diameter also led to excessive scatter in joint strength values, where it was not possible to meet the standard for 10 consecutive specimens (for each of the three tests). Implementation of high-speed data acquisition (1000Hz) enabled the capture of load curve profiles generated during FBJ. Load curve profiles were correlated with destructive testing results to discover the impact of process parameter combinations. Analysis of load curve profiles led to improvements in parameter selections of spindle speeds (revolutions per minute) and spindle feed-rates (inches per minute). Process parameters of 5000 RPM and 15 IPM reduced variation in load-curve profiles and destructive testing. Satisfactory joint strength was achieved in lap shear tension, cross-tension, and T-peel testing configurations with values of 10.1 kN, 4.1 kN, and 1.8 kN, respectively. The presence of wet adhesive had little impact on joint performance. Finally, the analysis of a load-curve profiles resulted in a criterion that allowed for distinguishing "good" welds from "bad" ones, where a threshold load of 6kN, or higher, during the dwell phase of welding was required in order to meet joint strength standards.

Yes / Scheduling is an important element that has a major impact on the efficiency of all manufacturing processes. It plays an important role in optimising the manufacturing times and costs resulting in energy efficient processes. It has been estimated that more than 75% of manufacturing processes occur in small batches. In such environments, processes must be able to perform a variety of operations on a mix of different batches. Batch-job scheduling optimisation is the response to such low batch manufacturing problems. The optimisation of batch-job process scheduling problem is still a challenge to researchers and is far from being completely solved due to its combinatorial nature. In this paper, a novel hybrid heuristic (HybH) solution approach for batch-job scheduling problem is presented with the objective of optimising the overall Makespan (Cmax). The proposed HybH is the combination of Index Based Heuristic (IBH) and the Finished Batch-Job (FBJ) process schedule. The heuristic assigns the first operation to a batch-job using IBH and the remaining operations on the basis FBJ process schedule. The FBJ process schedule gives priority to the batch-job with early finished operations, without violating the constraints of process order. The proposed HybH is explained with the help of a detailed example. Several benchmark problems are solved from the literature to check the validity and effectiveness of the proposed heuristic. The presented HybH has achieved batch-job process schedules which have outperformed the traditional heuristics. The results are encouraging and show that the proposed heuristic is a valid methodology for batch process scheduling optimisation.

Friction Bit Joining (FBJ) is a method used to join lightweight metals to advanced high-strength steels (AHSS). The automotive industry is experiencing pressure to improve fuel efficiency in their vehicles. The use of AHSS and aluminum will reduce vehicle weight which will assist in reducing fuel consumption. Previous research achieved joint strengths well above that which was required in three out of the four standard joint strength tests using DP980 AHSS and 7075 aluminum. The joints were mechanically tested and passed the lap-shear tension, cross-tension, and fatigue cycling tests. The t-peel test configuration never passed the minimum requirements. The purpose of continuing research was to increase the joint strength using FBJ to join the aluminum and AHSS the automotive industry desires to use specifically in the t-peel test. In this study FBJ was used to join 7085 aluminum and GADP1180 AHSS. The galvanic coating on the AHSS and its increased strength with the different aluminum alloy required that all the tests be re-evaluated and proven to pass the standard tests. FBJ is a two-step process that uses a consumable bit. In the first step the welding machine spins the bit to cut through the aluminum, and the second step applies pressure to the bit as it comes in contact with the AHSS to create a friction weld.

In this study, the dissimilar metals 5754 aluminum and DP980 ultra-high strength steel were joined using the friction bit joining (FBJ) process. The friction bits were made using one of three steels: 4140, 4340, or H13. Experiments were performed in lap shear, T-peel, and cross tension configurations, with the 0.070" thick 5754 aluminum alloy as the top layer through which the friction bit cut, and the 0.065" thick DP980 as the bottom layer to which the friction bit welded. All experiments were performed using a computer controlled welding machine that was purpose-built and provided by MegaStir Technologies. Through a series of designed experiments (DOE), weld processing parameters were varied and controlled to determine which parameters had a significant effect on weld strength at a 95% confidence level. The parameters that were varied included spindle rotational speeds, Z-command depths, Z-velocity plunge rates, dwell times, and friction bit geometry. Maximum lap shear weld strengths were calculated to be 1425.4lbf and were to be obtained using a bit tip length at 0.175", tip diameter at 0.245", neck diameter at 0.198", cutting and welding z-velocities at 2.6"/min, cutting and welding RPMs at 550 and 2160 respectively, cutting and welding z-commands at -0.07" and -0.12" respectively, cooling dwell at 500 ms, and welding dwell at 1133.8 ms. These parameters were further refined to reduce the weld creation time to 1.66 seconds. These parameters also worked well in conjunction with an adhesive to form weld bonded samples. The uncured adhesive had no effect on the lap shear strengths of the samples. Using the parameters described above, it was discovered that cross tension and T-peel samples suffered from shearing within the bit that caused the samples to break underneath the flange of the bit during testing. Visual inspection of sectioned welds indicated the presence of cracking and void zones within the bit.