Spelling suggestions: "subject:"field electron 2mission"" "subject:"field electron 2emission""
1 |
Development of carbon nanotubes with a diamond interlayer for field electron emission and heat transfer applications2015 October 1900 (has links)
Carbon Nanotubes (CNTs) have great potentials for Field Electron Emission (FEE) and Flow Boiling Heat Transfer (FBHT) applications. However, their weak adhesion on metallic substrates limits the development of CNTs in both applications. Diamond has high thermal conductivity and develops strong bonding with CNTs. The development of a diamond interlayer between CNTs and substrates is a feasible approach to address the adhesion problems. The purpose of this research was to develop a new CNT-based materials with a diamond interlayer for FEE and FBHT applications by focusing on four objectives: (1) enhancement of diamond thin film adhesion on a Cu substrate, (2) improvement of the CNT FEE stability, (3) reduction of the CNT FEE turn-on field, and (4) investigation of the FBHT performance of CNT based structures.
The CNTs and diamond thin films in this thesis were prepared by Microwave Plasma enhanced Chemical Vapor Deposition (MPCVD) and Hot Filament enhanced Chemical Vapor Deposition (HFCVD). The structure and chemical states of the diamond films and CNTs were characterized by Scanning Electron Microscopy (SEM), cross-sectional Transmission Electron Microscopy (TEM), X-Ray Diffraction (XRD), Raman spectroscopy, synchrotron based X-ray Absorption Spectroscopy (XAS). To deposit diamond thin films on a Cu substrate with sufficient adhesion strength, a sandblasting pretreatment and alloying with a tiny amount of Al were investigated. The adhesion of diamond thin films to substrates was evaluated by Vickers micro-hardness indentation. The FEE stability and turn-on field were measured by a Keithley 237 high voltage measuring unit. The FBHT property of the structures was tested repeatedly at different flow velocities to explore the dependence of heat transfer performance on certain parameters, including the flow patterns, Critical Heat Flux (CHF), and stability.
The results show that sandblasting pretreatment increases the surface roughness and surface defect density, thereby increasing diamond nucleation density and adhesion to the Cu substrate. Al alloying appears to inhibit the formation of graphite at the interface between diamond and the Cu substrate, which improves the chemical bonding between diamond and the Cu substrate and increases the adhesion strength between them.
The FEE testing results show that ultra-high FEE stability (more than 5000 minutes) was achieved for the CNTs with a diamond interlayer. This is attributed to the good contact at the diamond-CNT and diamond-substrate interfaces. The main factors that affect the CNT FEE turn-on field were also studied. By optimizing the structure, an FEE turn-on field of 5.1 V/μm was achieved and an emission barrier model for CNTs with a diamond interlayer on Cu substrate was used to explain the results. FBHT testing was done on CNTs with different structures and the results show that high heat transfer efficiency can be achieved on CNTs with a diamond interlayer at low mass fluxes.
|
2 |
Field electron emission from diamond and related films synthesized by plasma enhanced chemical vapor depositionLu, Xianfeng 21 December 2006
The focus of this thesis is the study of the field electron emission (FEE) of diamond and related films synthesized by plasma enhanced chemical vapor deposition. The diamond and related films with different morphologies and compositions were prepared in a microwave plasma-enhanced chemical vapor deposition (CVD) reactor and a hot filament CVD reactor. Various analytical techniques including scanning electron microscopy (SEM), atomic force microscopy (AFM), and Raman spectroscopy were employed to characterize the surface morphology and chemical composition.<p>The influence of surface morphology on the field electron emission property of diamond films was studied. The emission current of well-oriented microcrystalline diamond films is relatively small compared to that of randomly oriented microcrystalline diamond films. Meanwhile, the nanocrystalline diamond film has demonstrated a larger emission current than microcrystalline diamond films. The nanocone structure significantly improves the electron emission current of diamond films due to its strong field enhancement effect.<p>The sp2 phase concentration also has significant influence on the field electron emission property of diamond films. For the diamond films synthesized by gas mixture of hydrogen and methane, their field electron emission properties were enhanced with the increase of methane concentration. The field electron emission enhancement was attributed to the increase of sp2 phase concentration, which increases the electrical conductivity of diamond films. For the diamond films synthesized through graphite etching, the growth rate and nucleation density of diamond films increase significantly with decreasing hydrogen flow rate. The field electron emission properties of the diamond films were also enhanced with the decrease of hydrogen flow rate. The field electron emission enhancement can be also attributed to the increase of the sp2 phase concentration. <p>In addition, the deviation of the experimental Fowler-Nordheim (F-N) plot from a straight line was observed for graphitic nanocone films. The deviation can be mainly attributed to the nonuniform field enhancement factor of the graphitic nanocones. In low macroscopic electric field regions, electrons are emitted mainly from nanocone or nanocones with the largest field enhancement factor, which corresponds to the smallest slope magnitude. With the increase of electric field, nanocones with small field enhancement factors also contribute to the emission current, which results in a reduced average field enhancement factor and therefore a large slope magnitude.
|
3 |
Field electron emission from diamond and related films synthesized by plasma enhanced chemical vapor depositionLu, Xianfeng 21 December 2006 (has links)
The focus of this thesis is the study of the field electron emission (FEE) of diamond and related films synthesized by plasma enhanced chemical vapor deposition. The diamond and related films with different morphologies and compositions were prepared in a microwave plasma-enhanced chemical vapor deposition (CVD) reactor and a hot filament CVD reactor. Various analytical techniques including scanning electron microscopy (SEM), atomic force microscopy (AFM), and Raman spectroscopy were employed to characterize the surface morphology and chemical composition.<p>The influence of surface morphology on the field electron emission property of diamond films was studied. The emission current of well-oriented microcrystalline diamond films is relatively small compared to that of randomly oriented microcrystalline diamond films. Meanwhile, the nanocrystalline diamond film has demonstrated a larger emission current than microcrystalline diamond films. The nanocone structure significantly improves the electron emission current of diamond films due to its strong field enhancement effect.<p>The sp2 phase concentration also has significant influence on the field electron emission property of diamond films. For the diamond films synthesized by gas mixture of hydrogen and methane, their field electron emission properties were enhanced with the increase of methane concentration. The field electron emission enhancement was attributed to the increase of sp2 phase concentration, which increases the electrical conductivity of diamond films. For the diamond films synthesized through graphite etching, the growth rate and nucleation density of diamond films increase significantly with decreasing hydrogen flow rate. The field electron emission properties of the diamond films were also enhanced with the decrease of hydrogen flow rate. The field electron emission enhancement can be also attributed to the increase of the sp2 phase concentration. <p>In addition, the deviation of the experimental Fowler-Nordheim (F-N) plot from a straight line was observed for graphitic nanocone films. The deviation can be mainly attributed to the nonuniform field enhancement factor of the graphitic nanocones. In low macroscopic electric field regions, electrons are emitted mainly from nanocone or nanocones with the largest field enhancement factor, which corresponds to the smallest slope magnitude. With the increase of electric field, nanocones with small field enhancement factors also contribute to the emission current, which results in a reduced average field enhancement factor and therefore a large slope magnitude.
|
4 |
Growth And Characterization of ZnO Nanostructures for Device Applications : Field Emission, Memristor And Gas SensorsSingh, Nagendra Pratap January 2016 (has links) (PDF)
Zinc oxide (ZnO) is perhaps one of the most widely studied material in the last two decades. It has received so much of attention because of its incredible potential for wide ranging applications. ZnO is a wide band gap semiconductor (Eg = 3.37 eV at 300 K) with a rather large excitonic binding energy (~60 meV). This combination of properties makes it an ideal choice for several optoelectronic devices that can easily work at room temperature. ZnO is a truly multifunctional material possessing several desirable electrical, optical, optoelectronic, and piezoelectric properties. In addition, it is highly amenable to production of various kinds of nanostructures such as nanorods, nanotubes, nanoribbons, nanoneedles, etc., which makes it even more desirable for nanoscale devices. Examples of ZnO based nanodevices could include photodiodes, photodetectors, nano-lasers, field-emission devices and memristors. In order to make such devices, one could need device quality nanostructures that must be reproducible and cost effective. Naturally, one has to look for a synthesis process that has great controls and is relatively inexpensive. The study provided here shows that among the various methods available for ZnO synthesis, the microwave-assisted chemical synthesis offers outstanding advantages in terms of rapid growth of nanostructures, economical use of energy and excellent controls of process parameters.
In order to produce device quality ZnO nanostructures using microwave-assisted synthesis, one has to study the effect of various process parameters and optimise them for the desired growth. Therefore, in the current study, first, a systematic study was undertaken to synthesize ZnO nanostructures both in a aqueous and non-aqueous medium and their characterization was carried out in order to understand the effect of microwave power, time of irradiation, pressure, solvent and salt concentration, etc. The goal was to develop synthesis protocols for various kinds of nanostructures that could guarantee reproducibility, good yield, and device quality structures. This study has led to successful growth of ZnO nanostructures on various substrates, vertically aligned ZnO nanorods and templated arrays of desired structures, all with outstanding properties of the structures as confirmed by XRD, MicroRaman, photoluminescence, cathodoluminescence, FESEM, TEM, PFM studies and pole figure analysis.
Piezoelectric force microscopy (PFM) and physical property measurement system (PPMS, Quantum Design), have been used to study the multifunctional properties of ZnO nanostructures. The PFM is a powerful technique to measure the local piezoelectric coefficient of nanostructures and nanoscale thin films. PFM works on the converse piezoelectric effect in which electric potential is applied and mechanical strain is measured using a cantilever deflection. The PFM (Brucker’s AFM dimension Scan
Assist) was used to characterize individual ZnO nanorods. Extensive studies were carried out with PFM measurements and it was observed that the nanorods consistently showed high piezoelectric coupling coefficients (d33~50-154 pm/V). It was also found that the variation in d33 depended on morphology and size of nanostructure. The multifunctional properties were observed in small ZnO nanocrystals (NCs). Such high values of piezoelectric coupling coefficients open the door for novel ZnO based nanoscale sensors and actuators.
The synthesized ZnO nanostructures were further optimized and characterized keeping in view three device applications namely Field emission, Memristors and Gas Sensors. The fabrication and characterization of these three devices with ZnO nanostructure was carried out using electron beam lithography and direct laser writing micromachining. Device fabrication using lithography involved several steps such as substrate cleaning, photoresist spin coating, pre-baking, post-baking, pattern writing, developing, sputtering/deposition of material for lift-off, ZnO growth, and overlay lithography.
For field emission devices, high quality, well aligned, c-axis oriented ZnO nano-needles were grown on sputter coated Ti/Pt (20nm/100nm) on SiO2/Si substrate by rapid microwave-assisted method in aqueous medium. The diameter of the tip was found to be 1~2 nm and the length of the rod was approximately 3~5μm. For a particular batch the tip size, morphology, and lengths were found to be the same and highly repeatable. Pole figure analysis revealed that nanorods were highly oriented towards <002> direction. Field-emission measurements using the ZnO nanoneedles arrays as cathode showed very low turn-on electric field of 0.9 V/μm and a very high field enhancement factor ~ 20200. Such a high emission current density, low turn-on electric field, and high field enhancement factor are attributed to the high aspect ratio, narrow tip size, high quality and single crystallinity of the nanoneedles. The high emission current density, high stability, low threshold electric field (0.95 V/μm) and low turn-on field make the ZnO nanoneedle arrays one of the ideal candidates for field-emission displays and field emission sensors.
In the suitability of ZnO nanostructures for memristor application it was found that the single crystalline ZnO nanorods were not suitable as they did not show memristive behaviour but the ZnO nanorods with native defects exhibited considerable memristive behaviour. Therefore the microwave-assisted grown ZnO nanorods with defects were used to fabricate memristive devices. Single and multiple ZnO nanorods based memristors were fabricated using electron beam lithography. These devices were characterized electrically by measuring the hysteresis in the I/V characteristics. A high degree of repeatability has been established in terms of growth, device fabrication, and measurements. The switching in single nanorod based devices was found to have “ON-to- OFF” resistance ratio of approximately 104 and current switching ratio (ION/IOFF) of 106.
Gas sensing based on electrical resistance change depends on absorption and desorption rate of gases on the analyte which is governed by surface properties, morphologies and activation energy. Therefore, various morphologies of nanostructure were grown for gas sensing application. Through experimentation, the emphasis shifted to c-axis oriented ZnO nanostructures on SiO2 substrate for gas sensing. The c-axis orientation of ZnO nanostructures was preferred mainly due to its huge surface area. The measurements showed that the c-axis oriented ZnO nanorods were excellent hydrogen sensors, able to detect H2 as low concentration as 2 ppm, even when the sensing temperature is as low as 200 ˚C. However, oxygen sensing was achieved at a higher temperature (300 ˚C).
Thus, the study undertaken in this thesis presents a microwave based rapid and economical method for synthesizing high quality, device grade ZnO nanostructures, their extensive characterization that shows the multifunctional properties of these structures, and there examples of varied device applications of the synthesized nanostructures as field emitters, memristors, and gas sensors.
|
Page generated in 0.1054 seconds