Le présent travail est une étude expérimentale sur l’interaction entre flamme et turbulence. L’effet de la pression sur le plissement de flammes turbulentes prémélangées est caractérisé à l’aide de diagnostics laser et fil chaud. Dans un premier temps, la caractérisation de la turbulence générée par un système multi-échelles a été réalisée. Il a été démontré que ce dispositif amplifie le taux de turbulence de 40% par rapport à un dispositif mono-grille de maille équivalente. De même, les petites échelles de turbulence sont trouvées expérimentalement plus petites et plus énergétiques pour le système multi-grilles. A partir de ces résultats, l’étude des interactions entre flamme prémélangée et turbulence a été effectuée. En utilisant le diagnostic par tomographie laser, le front de flamme de plusieurs prémélanges a été étudié. En modifiant les conditions de mélange, l’effet des paramètres comme le nombre de Lewis, les conditions de turbulence ou les petites échelles ont pu être observés. Le faible impact des instabilités thermodiffusives sur la courbure du front de flamme et sur la dynamique de la flamme a été démontré. En revanche, l’effet des conditions de turbulence a été démontré comme important sur les caractéristiques du front de flamme. De plus, les résultats obtenus ont montré l’impact majeur de l’échelle de Taylor sur le plissement du front de flamme pour les conditions expérimentales de la présente étude. / The present work is an experimental study on the interactions between flame and turbulence. The pressure effect on the flame front wrinkling is characterised using laser diagnostics and hot wire anemometry. To begin with, the turbulence generated by a multi-grid system is characterised. It is shown that the present system produces a higher turbulence rate by 40% than for an equivalent mesh single-grid system. Moreover, the small turbulence scales sizes are experimentally found smaller with the multi-grid system. From those results, the interactions between premixed flames and turbulence were studied. By using the laser tomography diagnostic, the flame front of several gases premixes was observed. By changing the mixing conditions, the effect of parameters such as the Lewis number, the turbulence conditions and the small scale was observed. The low impact of the thermodiffusives instabilities in our conditions was demonstrated. However, the important effect of the turbulence conditions on the flame front characteristics was observed. Moreover, the present results showed the major impact of the Taylor micro scale on the flame front wrinkling for these study experimental conditions.

Ce travail porte sur la stabilisation de flammes prémélangées et swirlées de mélanges combustibles méthane/hydrogène/air avec différents taux de dilution d’azote et de dioxyde de carbone. Une tige centrale permet de stabiliser des flammes pour de faibles nombres de swirl. Le sommet de la flamme interagît éventuellement avec les parois de la chambre de combustion. L’objectif ces travaux est d’améliorer la connaissance des mécanismes qui gouvernent la stabilisation et la topologie de ces flammes. Ces travaux démontrent que le nombre de swirl, la composition du mélange combustible, la géométrie de la chambre de combustion ainsi que les conditions aux limites thermiques ont une grande influence sur la forme prise par la flamme. Le dispositif expérimental permet de modifier la forme et la taille de la chambre de combustion, le diamètre du tube d’injection et le nombre de swirl. Des conditions opératoires propices aux transitions de forme de flamme sont ensuite étudiées pour différentes configurations de brûleur. Une caractérisation expérimentale fouillée d’un point de fonctionnement est réalisée grâce à la Fluorescence Induite par Laser sur le radical Hydroxyle (OH-PLIF), la Vélocimétrie par Images de Particules (PIV) et la Phosphorescence Induite par Laser de phosphores sensibles à la température (LIP). Une base de donnée de l’écoulement et des conditions aux limites associées est obtenue sans et avec combustion. Les mécanismes qui contrôlent les transitions de formes de flamme sont ensuite analysés lorsque la flamme interagit avec les parois de la chambre de combustion. L’influence de la composition du mélange combustible, de la vitesse débitante et du nombre de swirl est caractérisée et il est démontré que la transition d’une flamme en V vers une flamme en M est déclenchée par un retour de flamme dans la couche limite le long d’une des parois latérales de la chambre de combustion. Les nombres sans dimension contrôlant ces transitions sont identifiés et un modèle de prévision de la forme de ces flammes est développé. La physique déterminant les transitions de forme de flammes est différente lorsque celles-ci n’interagissent pas avec les parois de la chambre de combustion. En utilisant le signal de chimiluminescence OH* et la OH-PLIF, il est montré que la teneur en hydrogène dans le combustible a une grande influence sur la forme de flamme. L’utilisation de la LIP et de thermocouples a également permis de montrer que les conditions aux limites thermiques jouent un rôle prépondérant sur la forme de flamme. Les effets combinés de l’étirement et des pertes thermiques sont examinés par l’utilisation conjointe de la PIV et de la OH-PLIF. Il est montré que les limites d’extinction de flammes pauvres prémélangées sont réduites par les pertes thermiques et que la transition d’une flamme en M vers une flamme en V est consécutive à l’extinction du front de flamme situé dans la couche de cisaillement externe du jet soumis à un étirement trop important. Ces expériences sont complétées par une analyse de la dynamique de ces flammes. Des modulations de la vitesse débitante à basse fréquence et à haute amplitude modifient la forme de flamme. La stabilisation de flammes CH4/H2/air diluées par du N2 ou du CO2 est finalement examinée. La zone de recirculation produite par la tige centrale permet d’alimenter la base de la flamme avec des gaz brûlés chauds et de stabiliser des flammes fortement diluées. Augmenter la fraction molaire de diluant dans le combustible réduit l’intensité de lumière émise par le radical OH*. Il est également montré que la composition du diluant a un impact sur le champ de température des gaz brûlés et des surfaces de la chambre de combustion. La dilution par du CO2 augmente les pertes thermiques par rayonnement des gaz brûlés. Cela réduit l’efficacité de la chambre de combustion équipée de quatre parois transparentes. [...] / This work deals with the stabilization of premixed turbulent swirling flames of methane/hydrogen/air combustible mixtures with different dilution rates of nitrogen and carbon dioxide. A central bluff body helps stabilizing the flames at low swirl numbers. The flame tip eventually impinges the combustor peripheral wall. The general objective is to gain understanding of the mechanisms governing the stabilization and the topology of these flames. It is found that the swirl number, the combustible mixture composition, the geometry of the combustor, and the thermal boundary conditions have a strong impact on the shape taken by these flames. The experimental setup used to characterize flames topologies is first described. Flames prone to topology bifurcations are selected and are studied for different arrangement of the combustor when the combustion chamber shape and size, the injection tube diameter, and swirl number are varied. One operating condition is fully characterized under non-reactive and reactive conditions using Planar Hydroxyl Laser Induced Fluorescence (OH-PLIF), Particle Imaging Velocimetry (PIV), and Laser Induced Phosphorescence of thermographic phosphors (LIP) to generate a detailed database of the flow and the corresponding boundary conditions. An analysis is then conducted to understand the mechanisms controlling shape bifurcations when the flame interacts with the combustor peripheral wall. Effects of the combustible mixture composition, the bulk flow velocity, and the swirl number are analyzed. It is shown that the transition from a V to an M flame is triggered by a flashback of the V flame tip in the boundary layer of the combustor peripheral wall. Dimensionless numbers controlling these transitions are identified and a simplified model is developed to help the prediction of the flame shapes. The physics of these shape bifurcations differs when the flame does not interact with the combustor wall. The large influence of the hydrogen enrichment in the fuel on the flame shape is analyzed using flame chemiluminescence and OH-PLIF. LIP and thermocouple measurements demonstrate that the thermal boundary conditions still have a strong impact on the flame topology. The combined effects of strain and heat losses are investigated using joint OH-PLIF and PIV experiments. It is shown that flammability limits of premixed flames are reduced due to heat losses and the transitions from M to V shaped flames is consecutive to localized extinctions of flame front elements located in the outer shear layer of the jet flow that are submitted to large strain rates. These experiments are completed by an analysis of the dynamics of methane/hydrogen/air flames. It is shown that low frequency and high amplitude velocity modulations generated by a loudspeaker alter the shape taken by these flames. The stabilization of methane/hydrogen/air flames diluted by nitrogen and carbon dioxide is finally examined. It was possible to stabilize swirled flames featuring important dilution rates due to the presence of the bluff body, installed on the axis of the injection tube. The recirculation zone behind this element supplies hot burnt gases to the flame anchoring point. Using OH* chemiluminescence imaging, it is shown than increasing the molar fraction of diluent in the fuel reduces the light emission from excited OH* radicals. The influence of dilution on the flame chemistry is emphasized with experiments conducted at a fixed thermal power and fixed adiabatic flame temperature. It is also demonstrated that the composition of the diluent has a strong influence on the temperature field of the burnt gases and of the combustor wall surfaces. Dilution with carbon dioxide increases radiative heat losses from the burnt gases in comparison to dilution with nitrogen. This penalizes the combustor efficiency equipped with four transparent quartz walls. [...]

Submitted by Claudinei Pracidelli (cpracide@ipen.br) on 2016-11-11T09:28:13Z No. of bitstreams: 0 / Made available in DSpace on 2016-11-11T09:28:13Z (GMT). No. of bitstreams: 0 / O monocloroacetato de sódio (MCAS) e o dicloroacetato de sódio (DCAS) são compostos tóxicos e irritantes ao ser humano e nocivos ao meio ambiente, sendo impurezas indesejáveis na cocoamido propil betaína (CAPB), que é um surfactante anfótero utilizado em produtos de consumo dos segmentos cosmético e domiciliar. Diante dos requisitos de concentração em nível de mg/kg exigidos pelos órgãos reguladores de saúde do governo, tornou-se mandatório o emprego de metodologia com limite de quantificação, precisão e exatidão adequados aos rígidos controles de processo pelos fabricantes da CAPB, bem como, dispor de técnicas convencionais com poder de resolução e proficiência pelo controle de qualidade e neste contexto inseriu-se a cromatografia a gás. Neste estudo foram estabelecidos os procedimentos analíticos que definiram as melhores condições para identificar e quantificar as impurezas MCAS e DCAS na matriz CAPB por meio da cromatografia a gás. A preparação das amostras consistiu da derivação das impurezas MCAS e DCAS a ésteres etílicos e a extração líquido-líquido em hexano para separar dos demais constituintes da matriz. Os modos de detecção acoplados à cromatografia a gás foram a ionização pela chama (GC/FID), a captura de elétrons (GC/ECD) e a espectrometria de massas (GC/MS). A validação comprovou que as metodologias são lineares entre 4 e 50 mg/kg com recuperação de 70 a 120%, apresentam limites de quantificação inferiores a 10 mg/kg e produziram médias e incertezas similares na amostra examinada, constituindo-se alternativas para a determinação de cloroacetatos em betaínas. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Spatially-resolved measurements of flame temperature have been demonstrated with diode lasers for the first time. The technique is based on the use of blue diode lasers to perform laser-induced fluorescence on indium atoms seeded to the flame. Temperature measurements have been carried out in laminar flames both by the two-line atomic fluorescence technique, and also by a novel line-shape thermometry method that requires the use of only a single diode laser. The first part of this work involved the development of blue extended cavity diode lasers with favourable tuning properties. Two custom-designed extended cavity diode lasers (ECDL) have been built, emitting at wavelengths of around 410 nm and 451 nm respectively. These devices are capable of mode-hop free tuning over ranges greater than 90 GHz. The performance of these devices exceeds that of commercially available systems and a patent application has been filed. High resolution fluorescence spectroscopy has been performed on both the 52P1/2→62S1/2 and 52P3/2→62S1/2 transitions of indium atoms seeded at trace quantities into atmospheric pressure flames. In both cases, the spectra obtained show excellent agreement with a theoretical fit based on the individual hyperfine components of the transition. The two ECDLs have been used to build a sensor for the measurement of temperature in combustion systems. It is much simpler, more compact, less expensive, and more versatile than any previously existing device. The two lasers were used sequentially to probe indium atoms seeded to the flame. The ratio of the resulting fluorescence signals is related to the relative populations in the two sub-levels of the spin-orbit split ground state of indium, and thus to the temperature. Temperature measurements have been successfully performed in a laminar flame and the data thus obtained do not need to be corrected by any ‘calibration constant’. This novel thermometry technique offers a robust alternative to traditional methods involving bulky high power lasers. A further development has been made by demonstrating a fluorescence line-shape thermometry technique requiring only a single diode laser excitation source. Progress has been made towards the goal of rapid temperature measurements appropriate to the study of turbulent flames. This involved the development of a simple technique for actively locking the wavelength of the blue diode laser to a resonance line of the tellurium molecule. A high-speed thermometry system would work by rapidly switching between the two locked laser beams using an optical modulator.

Cette thèse est consacrée à l’amélioration des capacités de prédiction des émissions polluantes (CO, NOx . . . ) des foyers de combustion de turboréacteurs. L’étude, exclusivement numérique, repose sur des simulations aux grandes échelles (ou LES pour Large-Eddy Simulation) basées sur des méthodes de tabulation de la chimie détaillée. L’approche PCM-FPI (pour Presumed Conditional Moments - Flame Prolongation of ILDM) a été étendue à la chimie des oxydes d’azote via la modification de la variable d’avancement. Différentes validations sur des configurations laminaires simples puis des flammes de laboratoire (Cabra, Sandia) sont présentées. Les résultats en terme de structure de flamme et de champs d’espèces chimiques sont confrontés aux mesures expérimentales. Le rôle du formaldéhyde comme marqueur de la zone réactionnelle est illustré à l’aide de calculs de flammes laminaires puis confirmé par un calcul 3D LES. Une analyse des spécificités de l’implantation de ce type de modèle sur des machines à architecture massivement parallèle est ensuite menée. Diverses modifications de la structure de la table et des méthodes d’interpolation sont réalisées, servant de base à une étude de sensibilité de maillage appliquée à la flamme Sandia D. Les difficultés relatives à la prédiction du NO dans les flammes turbulentes sont exposées : divers modèles de sous-maille sont alors employés et comparés. / This thesis is focused on the prediction capabilities of pollution (CO, NOx especially) for numerical tools applied to aeronautical combustion chambers. The modeling work is based on Large-Eddy Simulation methods coupled with a tabulated detailed chemistry approach. The PCM-FPI model, which stands for Presumed Conditional Moments - Flame Prolongation of ILDM, has been revised to take into account nitrogen chemistry through a modification of the progress variable. Several benchmarks and test-cases (laminar and turbulent flames) are gathered in this study : Cabra and Sandia flames have been computed and satisfactory comparisons with measurements are obtained. The role of CH2O as a marker of heat release is investigated, first in the frame of laminar premixed flames and then validated through LES runs. The challenges of the implementation of tabulated chemistry methods on massively parallel machines are discussed. Modifications are proposed regarding both the table structure and the interpolation methods leading to a mesh sensitivity review applied to the Sandia D flame. Difficulties arising when dealing with NOx chemistry in turbulent flows are presented : new Sub-Grid Scale models are introduced and investigated.

<p dir="ltr">Laser absorption spectroscopy (LAS) is a widely used technique to acquire path-integrated measurements of gas properties such as temperature and mole fraction. Although extremely useful, the application of LAS to study heterogeneous combustion environments can be challenging. For example, beam steering can be one such challenge that arises during measurements in heterogeneous combustion environments such as metallized propellant flames or measurements at high-pressure conditions. The ability to only obtain path integrated measurements has been a major challenge of conventional LAS techniques, especially in characterizing combustion environments with a non-uniform thermo-chemical distribution along the line of sight (LOS). Additionally, simultaneous measurements of multiple species using LAS with narrow-bandwidth lasers often necessitates employing multiple light sources. Aerospace applications, such as characterizing hypersonic flows may require ultrashort time resolution to study fast-evolving chemistry. Similarly, atmospheric entry most often requires measurements of atoms and molecules that absorb at wavelengths ranging from ultraviolet to mid-infrared. The availability of appropriate light sources for such measurements has been limited. In the past, several researchers have come up with diagnostic techniques to overcome the above-mentioned challenges to a certain extent. Most often, these solutions have been need-based while compromising on other diagnostic capabilities. Therefore, LAS diagnostics capable of acquiring broadband measurements with ultrafast time resolution and the ability to acquire measurements at wavelengths in ultraviolet through mid-infrared is required to study advanced combustion systems and for the development of advanced aerospace systems for future space missions. Ultrafast laser absorption spectroscopy is one such technique that provides broadband measurements, enabling simultaneous multi-species and high-pressure measurements. The light source utilized for ULAS provides the ultrafast time resolution necessary for resolving fast-occurring chemistry and more importantly the ability to acquire measurements at a wide range of wavelengths ranging from ultraviolet to far-infrared. The development and application of ULAS for characterizing propellant flames and hypersonic flows under non-equilibrium conditions by overcoming the above-mentioned challenges is presented here. </p><p>This work describes the development of a single-shot ultrafast laser absorption spectroscopy (ULAS) diagnostic for simultaneous measurements of temperature and concentrations of CO, NO, and H₂O in flames and aluminized fireballs of HMX (C₄H₈N₈O₈). Ultrashort (55 fs) pulses from a Ti:Sapphire oscillator emitting near 800 nm were amplified and converted into the mid-infrared through optical parametric amplification (OPA) at a repetition rate of 5 kHz. Ultimately, pulses with a spectral bandwidth of ≈600 cm^-1 centered near 4.9 µm were utilized in combination with a mid-infrared spectrograph to measure absorbance spectra of CO, NO, and H₂O across a 30 nm bandwidth with a spectral resolution of 0.3 nm. The gas temperature and species concentrations were determined by least-squares fitting simulated absorbance spectra to measured absorbance spectra. Measurements of temperature, CO, NO, and H₂O were acquired in an HMX flame burning in air at atmospheric pressure and the measurements agree well with previously published results. Measurements were also acquired in fireballs of HMX with and without 16.7 wt% H-5 micro-aluminum. Time histories of temperature and column densities are reported with a 1-σ precision of 0.4% for temperature and 0.3% (CO), 0.6% (NO), and 0.5% (H₂O), and 95% confidence intervals (C.I.) of 2.5% for temperature and 2.5% (CO), 11% (NO), and 7% (H₂O), thereby demonstrating the ability of ULAS to provide high-fidelity, multi-parameter measurements in harsh combustion environments. The results indicate that the addition of the micron-aluminum increases the fireball peak temperature by ≈100 K and leads to larger concentrations of CO. The addition of aluminum also increases the duration fireballs remain at elevated temperatures above 2000 K.</p><p dir="ltr">Next, the application of ULAS for dual-zone temperature and multi-species (CO, NO, H₂O, CO₂, HCl, and HF) measurements in solid-propellant flames is presented. ULAS measurements were acquired at three different central wavelengths (5.121 µm, 4.18 µm, and 3.044 µm) for simultaneous measurements of temperature and: 1) CO, NO, and H₂O, 2) CO₂ and HCl, and 3) HF and H₂O. Absorption measurements with a spectral resolution of 0.35 nm and bandwidth of 7 cm^-1, 18 cm^-1, and 35 cm^-1, respectively were acquired. In some cases, a dual-zone absorption spectroscopy model was implemented to accurately determine the gas temperature in the hot flame core and cold flame boundary layer via broadband absorption measurements of CO₂, thereby overcoming the impact of line-of-sight non-uniformities. Results illustrate that the hot-zone temperature of CO₂ agrees well with the equilibrium flame temperature and single-zone thermometry of CO, the latter of which is insensitive to the cold boundary layer due to the corresponding oxidation of CO to CO₂.</p><p dir="ltr">The initial development and implementation of an ultraviolet and broadband ultrafast-laser-absorption-imaging (UV-ULAI) diagnostic for one dimensional (1D) imaging of temperature and CN via its <i>B</i>²Σ⁺←<i>X</i>²Σ⁺absorption bands near 385 nm. The diagnostic was demonstrated by acquiring single-shot measurements of 1D temperature and CN profiles in HMX flames at a repetition rate of 25 Hz. Ultrashort pulses (55 fs) at 800 nm were generated using a Ti:Sapphire oscillator and then amplification and wavelength conversion to the ultraviolet was carried out utilizing an optical parametric amplifier and frequency doubling crystals. The broadband pulses were spectrally resolved using a 1200 l/mm grating and imaged on an EMCCD camera to obtain CN absorbance spectra with a resolution of ≈0.065 nm and a bandwidth of ≈4 nm (i.e. 260 cm^-1). Simulated absorbance spectra of CN were fit to the measured absorbance spectra using non-linear curve fitting to determine the gas properties. The spatial evolution of gas temperature and CN concentration near the burning surface of an HMX flame was measured with a spatial resolution of ≈10 µm. 1D profiles of temperature and CN concentration were obtained with a 1-σ spatial precision of 49.3 K and 4 ppm. This work demonstrates the ability of UV-ULAI to acquire high-precision, spatially resolved absorption measurements with unprecedented temporal and spatial resolution. Further, this work lays the foundation for ultraviolet imaging of numerous atomic and molecular species with ultrafast time resolution.</p><p dir="ltr">Ultraviolet ULAS was applied to characterize the temporal evolution of non-Boltzmann CN (<i>X</i>²Σ⁺) formed behind strong shock waves in N₂-CH₄ mixtures at conditions relevant to entry into Titan's atmosphere. An ultrafast (femtosecond) light source was utilized to produce 55 fs pulses near 385 nm at a repetition rate of 5 kHz and a spectrometer with a 2400 lines/mm grating was utilized to spectrally resolve the pulses after passing through the Purdue High-Pressure Shock Tube. This enabled broadband single-shot absorption measurements of CN to be acquired with a spectral resolution and bandwidth of ≈0.02 nm and ≈6 nm (≈402 cm^-1 at these wavelengths), respectively. A line-by-line absorption spectroscopy model for the <i>B</i>²Σ⁺←<i>X</i>²Σ⁺ system of CN was developed and utilized to determine six internal temperatures (two vibrational temperatures, four rotational) of CN from the (0,0), (1,1), (2,2) and (3,3) absorption bands. Measurements were acquired behind reflected shock waves in 5.65% CH₄ and 94.35% N₂ with an initial pressure of 1.56 mbar and incident shock speed of ≈2.1 km/s. For this test condition, the chemically and vibrationally frozen temperature of the mixture behind the reflected shock was 5000 K and the pressure was 0.6 atm. The high repeatability of the shock-tube experiments (0.3% variation in shock speed across tests) enabled multi-shock time histories of CN mole fraction and six internal temperatures to be acquired with a single-shot time resolution of less than 1 ns. The measurements revealed that CN <i>X</i>²Σ⁺ is non-Boltzmann rotationally and vibrationally for greater than 200 µs, thereby strongly suggesting that chemical reactions are responsible for the non-Boltzmann population distributions. </p><p><br></p>

Les interactions entre les flammes et les phénomènes thermiques sont le fil conducteur de ce travail. En effet, les flammes produisent de la chaleur, mais peuvent aussi être affectées par des transferts ou des sources de chaleur. La Simulation aux Grandes Echelles (SGE) est utilisée ici pour étudier ces interactions, en mettant l’accent sur deux sujets principaux: le transfert de chaleur aux parois et le contrôle de la combustion. Dans un premier temps, on étudie le transfert de chaleur aux parois dans un modèle de brûleur CH4/O2 de moteur-fusée. Dans un contexte deréutilisabilité et de réduction des coûts des lanceurs, qui constituent des enjeux majeurs, de nouveaux couples de propergols sont envisagés et les flux thermiques à la paroi doivent êtreprécisément prédits. Le but de ce travail est d’évaluer les besoins et les performances des SGEpour simuler ce type de configuration et de proposer une méthodologie de calcul permettant desimuler différentes configurations. Les résultats numériques sont comparés aux donnéesexpérimentales fournies par la Technische Universität München (Allemagne). Dans un deuxième temps, le contrôle de la combustion au moyen de décharges de plasma de type NRP (en anglaisNanosecond Repetitively Pulsed) est étudié. Les systèmes de turbines à gaz modernes utilisent en effet une combustion pauvre dans le but de réduire la consommation de carburant et les émissions de polluants. Les flammes pauvres sont connues pour être sujettes à des instabilités et le contrôle de la combustion peut jouer un rôle majeur dans ce domaine. Un modèle phénoménologique qui considère les décharges de plasma comme une source de chaleur est développé et appliqué à un brûleur pauvre avec prémélange CH4/Air stabilisé par un swirler. LesSGE sont réalisées afin d’évaluer les effets des décharges NRP sur la flamme. Les résultats numériques sont comparés aux observations expérimentales faites à la King Abdulla University ofScience and Technology (Arabie Saoudite) / Interactions between flames and thermal phenomena are the guiding thread of this work. Flamesproduce heat indeed, but can also be affected by it. Large Eddy Simulations (LES) are used hereto investigate these interactions, with a focus on two main topics: wall heat transfer andcombustion control. In a first part, wall heat transfer in a rocket engine sub-scale CH4/O2 burner isstudied. In the context of launchers re-usability and cost reduction, which are major challenges,new propellant combinations are considered and wall heat fluxes have to be precisely predicted.The aim of this work is to evaluate LES needs and performances to simulate this kind ofconfiguration and provide a computational methodology permitting to simulate variousconfigurations. Numerical results are compared to experimental data provided by the TechnischeUniversität München (Germany). In a second part, combustion control by means of NanosecondRepetitively Pulsed (NRP) plasma discharges is studied. Modern gas turbine systems use indeedlean combustion with the aim of reducing fuel consumption and pollutant emissions. Lean flamesare however known to be prone to instabilities and combustion control can play a major role in thisdomain. A phenomenological model which considers the plasma discharges as a heat source isdeveloped and applied to a swirl-stabilized CH4/Air premixed lean burner. LES are performed inorder to evaluate the effects of the NRP discharges on the flame. Numerical results are comparedwith experimental observations made at the King Abdulla University of Science and Technology(Saudi Arabia).

Η παρούσα διατριβή μελετά τις δυνατότητες υπολογισμού του πεδίου ροής δύο λειτουργικών παραμέτρων συμπεριλαμβανομένων του εκπεμπόμενου θορύβου και των εκπεμπόμενων ρύπων. Εξετάζεται η αλληλεπίδραση της καύσης με το ρευστο-θερμοδυναμικό πεδίο και τις χημικές αντιδράσεις. Περιγράφονται συνοπτικά οι διέπουσες εξισώσεις, οι μέθοδοι και τα μοντέλα της τυρβώδους καύσης και επισημαίνονται τα πλεονεκτήματα του μοντέλου των μεγάλων δινών (LES) το οποίο επιλέχθηκε εδώ. Αναπτύσσεται ένας εύχρηστος, από την ρευστοδυναμική υπολογιστική μεθοδολογία, πολυβηματικός μηχανισμός για δύο καύσιμα άμεσου ενδιαφέροντος το μεθάνιο και το προπάνιο. Προτείνεται, δηλαδή, ένα απλοποιημένο χημικό σχήμα για την οξείδωση των βασικών καυσίμων το οποίο περιέχει τον σχηματισμό του NΟx και της παραγωγής καπναιθάλης. Μετά από ανάλυση του ρόλου της καύσης στην ακουστική διακρίνονται οι δύο χαρακτηριστικοί τύποι: του θορύβου τυρβώδους καύσης (βόμβος – roar) και του θορύβου από τις ταλαντώσεις της καύσης (combustion oscillation). Παρουσιάζεται η κυματική εξίσωση και εισάγεται η έννοια του θερμο-ακουστικού όρου ο οποίος είναι συνάρτηση της απελευθερωμένης θερμότητας (q) στην φλόγα και εμφανίζεται ως όρος πηγής στην βασική εξίσωση. Στη συνέχεια η φλόγα εξετάζεται ως αυτόνομος πηγή αλλά και ως ενισχυτής θορύβου. Με την προσέγγιση της Προσομοίωσης των Μεγάλων Δινών (Large Eddy Simulation, LES) αναπτύχθηκε μια μεθοδολογία υπολογισμού του θορύβου που εκπέμπεται από το μέτωπο τυρβωδών φλογών διάχυσης. Στο πλαίσιο της προτεινομένης μεθοδολογίας το αποτέλεσμα ήταν η ανάπτυξη ενός τρισδιάστατου προγνωστικού υπολογιστικού κώδικα. Στην συνέχεια υπολογίζεται το αεροθερμοδυναμικό τυρβώδες πεδίο ροής μέσω τελειοποίησης κωδίκων του Εργαστηρίου Τεχνικής Θερμοδυναμικής, των κωδίκων που αναπτύχθηκαν στο πλαίσιο της παρούσης εργασίας αλλά και του εμπορικού κώδικα Fluent. Η μεθοδολογία, που αναπτύχθηκε με την παρούσα ερευνητική εργασία, πιστοποιήθηκε μέσω μιας σειράς πρωτότυπων μετρήσεων, του εκπεμπόμενου θορύβου στις συρρέουσες, εφαπτόμενες και ανυψωμένες και ανακυκλοφορούσες (χαμηλού και υψηλού λόγου καυσίμου/αέρα) φλόγες, σε πρωτότυπες πειραματικές διατάξεις του Εργαστηρίου. Συγκεκριμένα διαμορφώθηκε ένας καινοτόμος αεροδυναμικός φλογοσυγκρατητής πολλαπλών εγχύσεων που διατηρεί μια πλούσια γκάμα φλογών με ιδιαίτερα χαμηλό λόγο καυσίμου/αέρα. Επιτεύχθηκαν πειραματικές μετρήσεις, του ορμικού και θερμοκρασιακού πεδίου διαφόρων μορφών τυρβωδών φλογών, συντάχθηκαν σχετικά διαγράμματα και υπολογίσθηκαν οι αρχικές και οριακές συνθήκες των πειραμάτων. / In the present work the calculation of two parameters, the radiated noise and pollutants are studied. The interaction between combustion, the aerothermodynamical field and the chemical reactions is studied. The equations, the methods and the models of turbulent combustion are described here and the advantages of the large eddy simulation model (LES) which has been chosen for this case, are marked. A multi-step chemistry mechanism is developed for two fuels of great interest: methane and propane. A simple chemical scheme for the oxidation of basic fuels which includes the formation of NOx and soot is suggested in the present work. After analyzing the role of combustion in the acoustics two types of noise are distinguished the turbulent combustion noise and the noise from combustion oscillation. The wave equation is presented and the definition of thermo acoustic term which is a function of the heat release q in flame and it appears as a source term in the basic equation. The flame is examined as an autonomous source as well as a noise amplifier. With the approach of large eddy simulation (LES) a methodology for the noise calculation is developed which noise is from the turbulent diffusion flame front. In the place of the suggested methodology the result was the development of a 3-D computational code. The turbulent aerothermodynamical flow field is computed by codes has been developed in the laboratory of technical thermodynamic and by the commercial code (fluent). The methodology, which has been developed in the present work, has been certificated through a series of original measurements of the emitted noise in coaxial, tangential and lifted flames in original experimentallayouts.

Cette thèse est une contribution à l’étude des flammes de méthane turbulentes non prémélangées en rotation, dites swirlées, avec ou sans enrichissement en oxygène de l’oxydant. L’étude se focalise sur la stabilité de la flamme, les émissions polluantes et la dynamique du jet en non réactif et réactif. Notre dispositif expérimental se compose d’un brûleur à swirler coaxial avec injection radiale de méthane au voisinage de la sortie du brûleur. Ce dernier est confiné dans une chambre de combustion. La teneur en oxygène dans l’oxydant, le nombre de swirl géométrique et la richesse globale à l’injection sont les principaux paramètres qui peuvent être précisément contrôlés. La stabilité de la flamme est caractérisée par chimiluminescence OH*. Les émissions polluantes sont mesurées par des analyseurs en ligne via un prélèvement dans les gaz brûlés. La dynamique du jet est caractérisée principalement par PIV stéréoscopique dans un plan longitudinal et plusieurs plans transverses. La diffusion du méthane dans le jet swirlé est abordée qualitativement par fluorescence induite par laser de l’acétone dans un plan. À ce jour, peu de travaux portent sur la caractérisation notamment dynamique de ces flammes swirlées avec enrichissement en O2. La mise en rotation du jet est à l’origine d’une zone de recirculation centrale qui favorise la stabilisation de la flamme en régime pauvre et à grand nombre de Reynolds. L’étude des émissions polluantes montre que les régimes de combustion à l’air pour lesquels la flamme est liftée stable sont aussi ceux qui produisent du CO et du CH4 résiduel en des quantités non négligeables. L’enrichissement en oxygène permet alors de convertir les imbrûlés et ce pour de faibles enrichissements tout en améliorant la stabilité de flamme via une diminution de la hauteur d’accrochage et des fluctuations associées comme le confirment de précédentes études. L’augmentation des NOx par la voie thermique a été quantifiée pour des enrichissements en oxygène inférieurs à 30 % vol. L’étude systématique en non réactif et réactif apporte des détails sur la topologie tridimensionnelle du jet swirlé suivant les paramètres de l’étude. L’étude de la décroissance des vitesses et de la décroissance du nombre de swirl dans la direction de l’écoulement permetde mettre en évidence l’effet de la flamme sur le jet swirlé. Un couplage entre l’évolution du taux d’entraînement par la recirculation externe et les émissions polluantes est mis en évidence pour expliquer l’évolution des NOx suivant la richesse globale à l’injection. Nous avons proposé une modélisation des écoulements swirlés qui repose sur les écoulements à vorticité hélicoïdale afin d’identifier les caractéristiques principales des structures hélicoïdales au sein de l’écoulement. / This thesis is a contribution to the study of turbulent non-premixed swirling methane flames with or without oxygen addition in the oxidizer. The study deals with the flame stability, the pollutant emissions and the jet dynamic behaviour in non-reacting and reacting conditions. The burner, operating in a combustion chamber, consists of two concentric tubes with a swirler placed in an annular arrangement, which supplied the oxidant flow (air or oxygen-enriched air). The central pipe delivers fuel (methane) radially just below the burner exit plane. The oxygen content in the oxidizer, the geometric swirl number and the global equivalence ratio are the main parameters, which can be precisely set. OH* chemiluminescence imaging is used to characterize flame stability. Multi-gas analyzers are used to measure pollutant emissions in the exhaust gas. The flow is characterized using stereoscopic PIV measurements in different longitudinal and transverse planes. A qualitative study dealing with the methane diffusion imaging is also conducted by use of acetone planar laser-induced fluorescence. Up to now only few studies have examined the dynamic behavior of this type of swirled flames with oxygen addition. Introducing swirl allows creating a central recirculation zone which favors lean flame stabilization at higher Reynolds numbers. The mapping of the combustion regimes combined with the pollutant emission results show that the stable lifted flames are related to high CO and residual CH4 emission levels in the exhaust gas. Oxygen addition, even by a few percent, allows improving CO and unburned hydrocarbons conversion and increasing flame stability at the same time via a decrease of liftoff heights and the related fluctuations. The NOx emissions increase via the thermal pathway with increasing the oxygen-enrichment rate up to 30 % vol. A comparative study in non-reacting and reacting conditions is conducted to give insight into the tridimensional flow field topology varying the above-mentioned parameters. Mean streamwise velocity and swirl number decay rates show the flame effects on the flow dynamics. A coupling mechanism between the entrainment rate of the surroundings via the external recirculation and the pollutant emissions is proposed to explain the NOx emission trend with the global equivalence ratio. A model is also proposed based on the helical vortices to identify the main features of helix structures in the jet in non-reacting and reacting conditions.

This thesis is concerned with the development and application of laser induced thermal grating spectroscopy (LITGS) as a tool for thermometry in reacting and non-reacting flows. LITGS signals, which require resonant excitation of an absorbing species in the measurement region to produce a thermal grating, are acquired for systematic measurements of temperature in high pressure flames using OH and NO as target absorbing species in the burned gas. The signal obtained in LITGS measurements appears in the form of a time-based signal with a characteristic frequency proportional to the value or the sound speed of the local medium. With knowledge of the gas composition, the temperature can be derived from the speed of sound measurement. LITGS thermometry using resonant excitation of OH in the burned gas region of in oxygen enriched CH4/O2/N2 and CH4/air laminar flames was performed at elevated pressure (0.5 MPa) for a range of conditions. Measurements were acquired in oxygen enriched flames to provide an environment in which to demonstrate LITGS thermometry under high temperature conditions (up to 2900 K). The primary parameters that influence the quality of LITGS signal were also investigated. The signal contrast, which acts as a marker for the strength of the frequency oscillations, is shown to increase with an increase in the burnt gas density at the measurement point. LITGS employing resonant excitation of NO is also demonstrated for quantitative measurements of temperature in three environments – a static pressure cell at ambient temperature, a non-reacting heated jet at ambient pressure and a laminar premixed CH4/NH3/air flame operating at 0.5 MPa. Flame temperature measurements were acquired at various locations in the burned gas close to a water-cooled stagnation plate, demonstrating the capability of NO-LITGS thermometry for measuring the spatial distribution of temperature in combustion environments. In addition, the parameters that in influence the local temperature rise due to LITGS were also investigated in continuous vapour flows of acetone/air and toluene/air mixtures at atmospheric conditions. Acetone and toluene are commonly targeted species in previous LITGS measurements due to their favourable absorption characteristics. Results indicate that LITGS has the potential to produce accurate and precise measurements of temperature in non-reacting flows, but that the product of the pump intensity at the probe volume and the absorber concentration must remain relatively low to avoid significant localised heating of the measurement region.