The purpose of this study was to identify and explore factors affecting medicine availability within the district health services. A qualitative descriptive, exploratory and contextual research design was followed. The data collection was conducted through two focus group discussions comprising of pharmaceutical managers and district health services managers respectively. The study found that medicine was not consistently available in the various districts, especially in community health centres and primary health clinics. The factors contributing to the non-availability of medicines include challenges with deliveries from Medical Depots, poor medicine stock management, shortage of pharmacists and pharmacist’s assistants in the facilities, lack of the electronic medicine management systems and the separate existence of Pharmaceutical Services and Medical Depot within the province. The study made recommendations on how to improve medicine availability within the district health services. / Health Studies / M.A. (Health Studies)

The purpose of this study was to identify and explore factors affecting medicine availability within the district health services. A qualitative descriptive, exploratory and contextual research design was followed. The data collection was conducted through two focus group discussions comprising of pharmaceutical managers and district health services managers respectively. The study found that medicine was not consistently available in the various districts, especially in community health centres and primary health clinics. The factors contributing to the non-availability of medicines include challenges with deliveries from Medical Depots, poor medicine stock management, shortage of pharmacists and pharmacist’s assistants in the facilities, lack of the electronic medicine management systems and the separate existence of Pharmaceutical Services and Medical Depot within the province. The study made recommendations on how to improve medicine availability within the district health services. / Health Studies / M.A. (Health Studies)

Never before has the learning experience of incarcerated persons been captured by one of their fellow inmates. Public perception is that prisoners should be denied access to educational opportunities and be punished for the crimes committed. In this groundbreaking study, situated in the qualitative paradigm, I recorded the learning experiences of a group of inmates who are studying at undergraduate level, via distance learning. This phenomenological study originated from my experience of studying while incarcerated, and is aimed at increasing our knowledge of, and enhancing our understanding of incarcerated persons. The study focuses on the learning experiences and challenges encountered by these students. Data was collected from the participants using qualitative methods and analysed using content analysis. Interpretation of the data revealed a number of factors which impede the studies of these students. The investigation is of importance to all persons involved in the Corrections environment but also the general public as inmates return to their communities upon release. / Curriculum and Instructional Studies / M. Ed. (Curriculum Studies)

Thesis (D. Tech.) -- Central University of Technology, Free State, 2008

Thesis (M. Tech. Marketing) -- Central University of Technology, Free State, 2010

Thesis (M. Tech.) -- Central University of Technology, Free State, 2007 / With technology advancing, more and more people turn to the World Wide Web to conduct business. This may include buying and selling on the Web, advertising and monitoring of business activities. There is a big need for software and systems that enable remote monitoring and controlling of business activities. The Mechatronics Research Group of the Faculty of Engineering, Information and Communication Technology at the Central University of Technology, Free State, has identified a similar need. This research group has created an Automated Manufacturing System around which research topics revolve. They want to monitor this Automated Manufacturing System from remote locations like their offices or, if possible, from home. The Remote Information Management (RIM) System was developed, using the Rapid Application Development (RAD) Methodology. The reasons why this methodology was used, is because it is the best to use in a changing environment, when the system needs to be developed very quickly and when most of the data is already available. This is a good description of the Automated Manufacturing System’s environment. The RAD methodology consists of four stages: Requirements Planning, User Design, Rapid Construction and Transition. Project Management is used throughout these stages to ensure that the project goes according to plan. Development of the RIM system went through all four stages and project management was applied. The final system consisted of a Web Page with Web Camera views of the Automated Manufacturing System. The application that was developed using National Instruments LabVIEW, Microsoft Visual C++, and Microsoft Excel, is embedded in this Web Page. This application is called a Virtual Instrument (VI). The VI shows real-time data from the Automated Manufacturing System. Control over the VI can be granted and will allow the remote user to create reports on how many different products was produced and system downtimes. A system like the RIM System has advantages in the business world. It can enable telecommuting and will allow employees and managers to monitor (and even control) manufacturing systems, or any system connected to a PLC, from remote locations.

Thesis (D. Tech. ( Mechanical Engineering )) - Central University of technology, Free State, 2012 / In this study an alternative indirect Rapid Tooling process is proposed. It essentially consists of producing sand moulds by Additive Manufacturing (AM) processes followed by casting of tools in the moulds. Various features of this tool making method have been investigated. A process chain for the proposed tool manufacturing method was conceptually developed. This process chain referred to as Rapid Casting for Tooling (RCT) is made up of five steps including Computer Aided Design (CAD) modeling, casting simulation, AM of moulds, metal casting and finishing operations. A validation stage is also provided to determine the suitability of the tool geometry and material for RCT. The theoretical assessment of the RCT process chain indicated that it has potential benefits such as short manufacturing time, low manufacturing cost and good quality of tools in terms of surface finish and dimensional accuracy. Focusing on the step of AM of the sand moulds, the selection of available AM processes between the Laser Sintering (LS) using an EOSINT S 700 machine and Three Dimensional Printing using a Z-Corporation Spectrum 550 printer was addressed by means of the Analytic Hierarchy Process (AHP). The criteria considered at this stage were manufacturing time, manufacturing cost, surface finish and dimensional accuracy. LS was found to be the most suitable for RCT compared to Three Dimensional Printing. The overall preferences for these two alternatives were respectively calculated at 73% and 27%. LS was then used as the default AM process of sand moulds in the present research work. A practical implementation of RCT to the manufacturing of foundry tooling used a case study provided by a local foundry. It consisted of the production of a sand casting pattern in cast iron for a high pressure moulding machine. The investigation confirmed the feasibility of RCT for producing foundry tools. In addition it demonstrated the crucial role of casting simulation in the prevention of casting defects and the prediction of tool properties. The challenges of RCT were found to be exogenous mainly related to workmanship. An assessment of RCT manufacturing time and cost was conducted using the case study above mentioned as well as an additional one dealing with the manufacturing of an aluminium die for the production of lost wax patterns. Durations and prices of RCT steps were carefully recorded and aggregated. The results indicated that the AM of moulds was the rate determining and cost driving step of RCT if procurement of technology was considered to be a sunk cost. Overall RCT was found to be faster but more expensive than machining and investment casting. Modern surface analyses and scanning techniques were used to assess the quality of RCT tools in terms of surface finish and dimensional accuracy. The best surface finish obtained for the cast dies had Ra and Rz respectively equal to 3.23 μm and 11.38 μm. In terms of dimensional accuracy, 82% of cast die points coincided with die Computer Aided Design (CAD) data which is within the typical tolerances of sand cast products. The investigation also showed that mould coating contributed slightly to the improvement of the cast tool surface finish. Finally this study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. Because of the above, it was concluded that light machining will always be required to improve the surface finish and the dimensional accuracy of cast tools. Durability was the last characteristic of RCT tools to be assessed. This property was empirically inferred from the mechanical properties and metallographic analysis of castings. Merit of durability figures of 0.048 to 0.152 were obtained for the cast tools. It was found that tools obtained from Direct Croning (DC) moulds have merit of durability figures three times higher than the tools produced from Z-Cast moulds thus a better resistance to abrasion wear of the former tools compared to the latter.

Thesis (D. Tech. (Electrical Engineering)) - Central University of technology, Free State, 2012 / Radio frequency identification technology (RFID) has emerged as a key technology for automatic identification and promises to revolutionize business processes. While RFID technology adoption is improving rapidly, reliable and widespread deployment of this technology still faces many significant challenges. The key deployment challenges include how to use the simple, unreliable raw data generated by RFID deployments to make business decisions; and how to manage a large number of deployed RFID devices. In this thesis, a multi-agent based RFID middleware which addresses some of the RFID data and device management challenges was developed. The middleware developed abstracts the auto-identification applications from physical RFID device specific details and provides necessary services such as device management, data cleaning, event generation, query capabilities and event persistence. The use of software agent technology offers a more scalable and distributed system architecture for the proposed middleware. As part of a multi-agent system, application-independent domain ontology for RFID devices was developed. This ontology can be used or extended in any application interested with RFID domain ontology. In order to address the event processing tasks within the proposed middleware system, a temporal-based RFID data model which considers both applications’ temporal and spatial granules in the data model itself for efficient event processing was developed. The developed data model extends the conventional Entity-Relationship constructs by adding a time attribute to the model. By maintaining the history of events and state changes, the data model captures the fundamental RFID application logic within the data model. Hence, this new data model supports efficient generation of application level events, updating, querying and analysis of both recent and historical events. As part of the RFID middleware, an adaptive sliding-window based data cleaning scheme for reducing missed readings from RFID data streams (called WSTD) was also developed. The WSTD scheme models the unreliability of the RFID readings by viewing RFID streams as a statistical sample of tags in the physical world, and exploits techniques grounded in sampling theory to drive its cleaning processes. The WSTD scheme is capable of efficiently coping with both environmental variations and tag dynamics by automatically and continuously adapting its cleaning window size, based on observed readings.

Thesis (M. Tech.) -- Central University of Technology, Free State, 2009

Thesis (M. Tech.) - Central University of Technology, Free State, 2008