This thesis presents some new techniques that were developedfor continuous chemical analysis of a paper furnish. First, ageneral background is presented, covering topics from theorigins of papermaking to present day. A short introduction topapermaking chemistry and a variety of presently availableon-line chemical analysers and measurement strategies are alsodiscussed. A method is described for the continuous fractionation of apaper furnish containing coarse fibres (&gt;10µm) in orderto obtain a sample for analytical purposes (Paper I). Aconsistent sample, containing a representative fraction of thedissolved and colloidal substances (DCS) present in the bulkfurnish, was achieved by preventing cake formation on a filtersurface. A combination of turbulent flow above a membranefilter, while continuously withdrawing a relatively low samplevolume, were key factors in the prevention of filterfouling. For the continuous flow-extraction of DCS, a technique isdescribed whereby the extracting solvent was injected at a highvelocity into a continuous flow of analyte (Paper II).Comparison with conventional flow extraction showed anextraction enhancement of up to 9 times for colloidaltriglycerides. To achieve a continuous determination of chemicalsubstances, a real-time fully automated colorimetric titrationapparatus was developed (Paper III&amp;IV). This was achievedby using a series of micro-machined mixing channels for thecontinuous flow of analyte, with a sequence of detection unitsand titrant addition points along the flowpath (Paper III). Afuzzy logiccontroller was implemented to continuously adaptfor changes in the sample concentration, providing thepossibility of titrating over two orders of magnitude in sampleconcentration with minimal loss of accuracy (Paper IV). Also, a system is presented whereby the filtration apparatus(Paper I) is combined with the titration device (Paper III&amp;IV) in order to continuously determine total charge (orcolloidal charge) of a paper furnish in real-time (Paper V).This was achieved by utilising a back-titration approach andselected examples are presented showing the dynamicinteractions between wood fibres and polyelectrolyte adsorptionat various conditions of pH and polyelectrolyte molecularweight. Finally, some suggestions for a more comprehensive wet-endchemical monitoring platform are discussed and the role of thepresent work in evaluated in this context. <b>Keywords:</b>Chemical monitoring, continuous flowextraction, cross-flow filtration, dissolved and colloidalcomponents, fuzzy-logic control, on-line system, pitchanalysis, polyelectrolyte titration, process control, samplework-up, titrimetric analysis.

Active safety systems for road vehicles have been improved considerably in recent years along with technological advances and the increasing demand for road safety. In the development route of active safety systems which started with introduction of digital controlled ABS in the late seventies, vehicle stability control systems have been developed which today, with an integration approach, incorporate ABS and other previously developed active safety technologies. ABS, as a main part of this new structure, still maintains its importance. In this thesis, a design methodology of an antilock braking system controller for four wheeled road vehicles is presented with a detailed simulation work. In the study, it is intended to follow a flexible approach for integration with unified control structure of an integrated active safety system. The objective of the ABS controller, as in the previous designs in literature, is basically to provide retention of vehicle directional control capability and if possible shorter braking distances by controlling the wheel slip during braking. iv A hierarchical structure was adopted for the ABS controller design. A high-level controller, through vehicle longitudinal acceleration based estimation, determines reference slip values and a low-level controller attempts to track these reference slip signals by modulating braking torques. Two control alternatives were offered for the design of the low-level controller: Fuzzy Logic Control and PID Control. Performance of the ABS controller was analyzed through extensive simulations conducted in MATLAB/Simulink for different road conditions and steering maneuvers. For simulations, an 8 DOF vehicle model was constructed with nonlinear tires.

Active vehicle safety systems for road vehicles play an important role in accident prevention. In recent years, rapid developments have been observed in this area with advancing technology and electronic control systems. Active yaw control is one of these subjects, which aims to control the vehicle in case of any impending spinning or plowing during rapid and/or sharp maneuver. In addition to the development of these systems, integration and cooperation of these independent control mechanisms constitutes the current trend in active vehicle safety systems design. In this thesis, design methodology and simulation results of an active yaw control system for two axle road vehicles have been presented. Main objective of the yaw control system is to estimate the desired yaw behavior of the vehicle according to the demand of the driver and track this desired behavior accurately. The design procedure follows a progressive method, which first aims to design the yaw control scheme without regarding any other stability parameters, followed by the development of the designed control scheme via taking other stability parameters such vehicle sideslip angle into consideration. A two degree of freedom vehicle model (commonly known as &ldquo / Bicycle Model&rdquo / ) is employed to model the desired vehicle behavior. The design of the controller is based on Fuzzy Logic Control, which has proved itself useful for complex nonlinear design problems. Afterwards, the proposed yaw controller has been modified in order to limit the vehicle sideslip angle as well. Integration of the designed active yaw control system with other safety systems such as Anti-Lock Braking System (ABS) and Traction Control System (TCS) is another subject of this study. A fuzzy logic based wheel slip controller has also been included in the study in order to integrate two different independent active systems to each other, which, in fact, is a general design approach for real life applications. This integration actually aims to initiate and develop the integration procedure of the active yaw control system with the (ABS). An eight degree of freedom detailed vehicle model with nonlinear tire model is utilized to represent the real vehicle in order to ensure the validity of the results. The simulation is held in MATLAB/Simulink environment, which has provided versatile design and simulation capabilities for this study. Wide-ranging simulations include various maneuvers with different road conditions have been performed in order to demonstrate the performance of the proposed controller.

Active safety systems for road vehicles make a crucial preventive contribution to road safety. In recent years, technological developments and the increasing demand for road safety have resulted in the integration and cooperation of these individual active safety systems. Traction control system (TCS) is one of these individual systems, which is capable of inhibiting wheel-spin during acceleration of the vehicle on slippery surfaces. In this thesis, design methodology and simulation results of a traction control system for four wheeled road vehicles are presented. The objective of the TCS controller is basically to improve directional stability, steer-ability and acceleration performance of vehicle by controlling the wheel slip during acceleration. In this study, the designed traction control system based on fuzzy logic is composed of an engine torque controller and a slip controller. Reference wheel slip values were estimated from the longitudinal acceleration data of the vehicle. Engine torque controller determines the throttle opening angle corresponding to the desired wheel torque, which is determined by a slip controller to track the reference slip signals. The wheel torques delivered by the engine are compensated by brake torques according to the desired wheel torque determined by the slip controller. Performance of the TCS controller was analyzed through several simulations held in MATLAB/Simulink for different road conditions during straight line acceleration and combined acceleration and steering. For simulations, an 8 DOF nonlinear vehicle model with nonlinear tires and a 2 DOF nonlinear engine model were built.

<p>This thesis presents some new techniques that were developedfor continuous chemical analysis of a paper furnish. First, ageneral background is presented, covering topics from theorigins of papermaking to present day. A short introduction topapermaking chemistry and a variety of presently availableon-line chemical analysers and measurement strategies are alsodiscussed.</p><p>A method is described for the continuous fractionation of apaper furnish containing coarse fibres (>10µm) in orderto obtain a sample for analytical purposes (Paper I). Aconsistent sample, containing a representative fraction of thedissolved and colloidal substances (DCS) present in the bulkfurnish, was achieved by preventing cake formation on a filtersurface. A combination of turbulent flow above a membranefilter, while continuously withdrawing a relatively low samplevolume, were key factors in the prevention of filterfouling.</p><p>For the continuous flow-extraction of DCS, a technique isdescribed whereby the extracting solvent was injected at a highvelocity into a continuous flow of analyte (Paper II).Comparison with conventional flow extraction showed anextraction enhancement of up to 9 times for colloidaltriglycerides.</p><p>To achieve a continuous determination of chemicalsubstances, a real-time fully automated colorimetric titrationapparatus was developed (Paper III&IV). This was achievedby using a series of micro-machined mixing channels for thecontinuous flow of analyte, with a sequence of detection unitsand titrant addition points along the flowpath (Paper III). Afuzzy logiccontroller was implemented to continuously adaptfor changes in the sample concentration, providing thepossibility of titrating over two orders of magnitude in sampleconcentration with minimal loss of accuracy (Paper IV).</p><p>Also, a system is presented whereby the filtration apparatus(Paper I) is combined with the titration device (Paper III&IV) in order to continuously determine total charge (orcolloidal charge) of a paper furnish in real-time (Paper V).This was achieved by utilising a back-titration approach andselected examples are presented showing the dynamicinteractions between wood fibres and polyelectrolyte adsorptionat various conditions of pH and polyelectrolyte molecularweight.</p><p>Finally, some suggestions for a more comprehensive wet-endchemical monitoring platform are discussed and the role of thepresent work in evaluated in this context.</p><p><b>Keywords:</b>Chemical monitoring, continuous flowextraction, cross-flow filtration, dissolved and colloidalcomponents, fuzzy-logic control, on-line system, pitchanalysis, polyelectrolyte titration, process control, samplework-up, titrimetric analysis.</p>

This thesis proposes a modification to an air to surface guided munition (ASGM) from bang-bang control scheme to continuous control scheme with a little cost. In this respect, time domain system identification analysis is applied to the control actuation system (CAS) of ASGM in order to obtain its mathematical model and controller is designed using pulse width modulation technique. With this modification, canards would be deflected as much as it is commanded to. Seeker signals are also post-processed to obtain the angle between the velocity vector and target line of sight vector. The seeker is modeled using an artificial neural network. Non-linear flight simulation model is built using MATLAB Simulink and obtained seeker and CAS models are integrated to the whole flight simulation model having 6 degrees of freedom. As a flight control unit, fuzzy logic controller is designed, which is a suitable choice if an inertial measurement sensor will not be mounted on the munition. Finally, simulation studies are carried out in order to compare the performance of the &ldquo / ASGM&rdquo / and &ldquo / improved ASGM&rdquo / and the superiority of the new design is demonstrated.

Les réserves limitées de combustibles fossiles et la pollution entrainée par les gaz produits ouvrent la voie à desressources énergétiques renouvelables (RER) alternatives et prometteuses telles que les ressources solaires (RS)et les ressources éoliennes (RE). Ces ressources sont librement disponibles et respectueuses de l'environnement.Cependant, les RER sont de nature intermittente. Par conséquent, il existe un besoin de lissage des fluctuations depuissance en stockant l'énergie pendant les périodes de surproduction pour la restituer au réseau lorsque lademande énergétique devient importante. Les systèmes de stockage de l'énergie (SSE) peuvent alors être utilisésde manière appropriée à cette fin.L'utilisation de plusieurs sources d'énergie et de stockeurs pour construire des systèmes de puissance hybrides(SPH) exige une stratégie de gestion de l'énergie pour atteindre le minimum de coût des SPH et un équilibre entrela production et la consommation de l'énergie. Cette méthode de gestion de l'énergie est un mécanisme pourobtenir une production d'énergie idéale et pour satisfaire convenablement la demande de charge à rendementrelativement élevé.Dans cette thèse, un SPH intégrant production électrique photovoltaïque, éolienne, une micro-turbine à gaz ainsiqu'un système de stockage de l'électricité par le vecteur hydrogène est considéré. Le but de cette hybridation estde construire un système fiable, qui est en mesure de fournir la charge et qui a la capacité de stocker l'énergieexcédentaire sous forme hydrogène et de la réutiliser plus tard. En outre, le problème d'ombrage partiel dePanneaux Photovoltaïques est étudié de manière approfondie. Une nouvelle solution basée sur des interrupteurssimples et un contrôle par logique floue intégré dans une carte électronique dSPACE a été proposée. Unereconfiguration des panneaux photovoltaïques en temps réel et de déconnexion de ceux ombragés est égalementeffectuée en cherchant à minimiser les pertes de puissance. Le couplage thermique entre ces panneauxphotovoltaïques et un électrolyseur à membrane polymère est également étudié, à l'échelle système. Enrécupérant une partie de l'énergie thermique reçue par les panneaux, une amélioration du rendement du systèmehybride PPVELS MEP est réalisée / The limited reserves of fossil fuel and the pollution gases produced pave the way to promising alternativeRenewable Energy Sources (RESs) such as Solar Energy Sources (SESs) and Wind Energy Sources (WESs).SESs and WESs are freely available and environmentally friendly. However, RESs are intermittent in nature.Therefore, the smoothing of power fluctuations by storing the energy during periods of oversupply and restore it tothe grid when demand becomes necessary. Accordingly, Energy Storage Systems (ESSs) can be appropriatelyused for this purpose.Using several energy sources for constructing HPSs alongside with ESS will require an energy managementstrategy to achieve minimum HPS cost and optimal balance between energy generation and energy consumption.This energy management method is a mechanism to achieve an ideal energy production and to conveniently satisfythe load demand at relatively high efficiency.In this thesis, a Hybrid Power System (HPS) including Renewable Energy Sources (RESs) such as main sourcescombined with Gas Micro-Turbine (GMT) and hydrogen storage system such as Back-up Sources (BKUSs) hasbeen presented. The aim of this hybridization is to build a reliable system, which is able to supply the load andhaving the ability to store the excess energy in hydrogen form and reuse it later when demanded. Consequently, thestored energy at the end of each cycle will be zero and a minimum generated power cost is achieved. In addition,partial shading problem of Photovoltaic (PV) panels is comprehensively studied and a new solution based on simpleswitches and Fuzzy Logic Control (FLC) integrated into dSPACE electronic card is created. Consequently, a realtime PV panels reconfiguration and disconnecting shaded ones is performed and minimum power losses isachieved. Then, the PV panels are connected to a Proton Exchange Membrane Electrolyser (PEM ELS). Theemitted temperature by the PV panels is transferred to the endothermic element PEM ELS. Consequently, anefficiency enhancement of the hybrid system PVPEM ELS is realized.

Development of electric vehicles is motivated by global concerns over the need for environmental protection. In addition to its zero-emission characteristics, an electric propulsion system enables high performance torque control that may be used to maximize vehicle performance obtained from energy-efficient, low rolling resistance tires typically associated with degraded road-holding ability. A simultaneous plant/controller optimization is performed on an electric vehicle traction control system with respect to conflicting energy use and performance objectives. Due to system nonlinearities, an iterative simulation-based optimization approach is proposed using a system model and a genetic algorithm (GA) to guide search space exploration. The system model consists of: a drive cycle with a constant driver torque request and a step change in coefficient of friction, a single-wheel longitudinal vehicle model, a tire model described using the Magic Formula and a constant rolling resistance, and an adhesion gradient fuzzy logic traction controller. Optimization is defined in terms of the all at once variable selection of: either a performance oriented or low rolling resistance tire, the shape of a fuzzy logic controller membership function, and a set of fuzzy logic controller rule base conclusions. A mixed encoding, multi-chromosomal GA is implemented to represent the variables, respectively, as a binary string, a real-valued number, and a novel rule base encoding based on the definition of a partially ordered set (poset) by delta inclusion. Simultaneous optimization results indicate that, under straight-line acceleration and unless energy concerns are completely neglected, low rolling resistance tires should be incorporated in a traction control system design since the energy saving benefits outweigh the associated degradation in road-holding ability. The results also indicate that the proposed novel encoding enables the efficient representation of a fix-sized fuzzy logic rule base within a GA.

Development of electric vehicles is motivated by global concerns over the need for environmental protection. In addition to its zero-emission characteristics, an electric propulsion system enables high performance torque control that may be used to maximize vehicle performance obtained from energy-efficient, low rolling resistance tires typically associated with degraded road-holding ability. A simultaneous plant/controller optimization is performed on an electric vehicle traction control system with respect to conflicting energy use and performance objectives. Due to system nonlinearities, an iterative simulation-based optimization approach is proposed using a system model and a genetic algorithm (GA) to guide search space exploration. The system model consists of: a drive cycle with a constant driver torque request and a step change in coefficient of friction, a single-wheel longitudinal vehicle model, a tire model described using the Magic Formula and a constant rolling resistance, and an adhesion gradient fuzzy logic traction controller. Optimization is defined in terms of the all at once variable selection of: either a performance oriented or low rolling resistance tire, the shape of a fuzzy logic controller membership function, and a set of fuzzy logic controller rule base conclusions. A mixed encoding, multi-chromosomal GA is implemented to represent the variables, respectively, as a binary string, a real-valued number, and a novel rule base encoding based on the definition of a partially ordered set (poset) by delta inclusion. Simultaneous optimization results indicate that, under straight-line acceleration and unless energy concerns are completely neglected, low rolling resistance tires should be incorporated in a traction control system design since the energy saving benefits outweigh the associated degradation in road-holding ability. The results also indicate that the proposed novel encoding enables the efficient representation of a fix-sized fuzzy logic rule base within a GA.

The goal of this thesis is to develop nontraditional strategies to provide motion control for different engineering applications. We focus our attention on three topics: 1) roll reduction of ships in a seaway; 2) response reduction of buildings under seismic excitations; 3) new training strategies and neural-network configurations. The first topic of this research is based on a multidisciplinary simulation, which includes ship-motion simulation by means of a numerical model called LAMP, the modeling of fins and computation of the hydrodynamic forces produced by them, and a neural-network/fuzzy-logic controller. LAMP is based on a source-panel method to model the flowfield around the ship, whereas the fins are modeled by a general unsteady vortex-lattice method. The ship is considered to be a rigid body and the complete equations of motion are integrated numerically in the time domain. The motion of the ship and the complete flowfield are calculated simultaneously and interactively. The neural-network/fuzzy-logic controller can be progressively trained. The second topic is the development of a neural-network-based approach for the control of seismic structural response. To this end, a two-dimensional linear model and a hysteretic model of a multistory building are used. To control the response of the structure a tuned mass damper is located on the roof of the building. Such devices provide a good passive reduction. Once the mass damper is properly tuned, active control is added to improve the already efficient passive controller. This is achieved by means of a neural network. As part of the last topic, two new flexible and expeditious training strategies are developed to train the neural-network and fuzzy-logic controllers for both naval and civil engineering applications. The first strategy is based on a load-matching procedure, which seeks to adjust the controller in order to counteract the loads (forces and moments) which generate the motion that is to be reduced. A second training strategy provides training by means of an adaptive gradient search. This technique provides a wide flexibility in defining the parameters to be optimized. Also a novel neural-network approach called modal neural network is designed as a suitable controller for multiple-input multiple output control systems (MIMO). / Ph. D.