In order to more accurately quantify the behavior and degradation of bridges throughout their service life, the Federal Highway Administration lunched the Long-Term Bridge Performance Program. As part of this program an I-girder, integral abutment bridge near Perry, Utah and a two span, box-girder bridge south of Sacramento, California were instrumented with foil strain gauges, velocity transducers, vibrating wire strain gauges, thermocouples, and tiltmeters. In this research study, data from the thermocouples was used to calculate average bridge temperature and compare it to the recommended design criteria in accordance to the 2010 LRFD Bridge Design Specifications of the American Association of State Highway and Transportation Officials (AASHTO). The design maximum average bridge temperature defined in the 2010 LRFD Bridge Design Specifications was exceeded for both bridges. The accuracy of the 1991 Kuppa Method and the 1976 Black and Emerson Method to estimate the average bridge temperature based on ambient temperature was studied and a new method that was found to be more accurate was proposed. Long-term predictions of average bridge temperature for both bridges were calculated. Temperature gradients were measured and compared to the 2010 AASHTO LRFD Bridge Design Specifications and the 1978 Priestley Method. Calculated flexural stresses as a function of maximum positive and negative temperature gradients were found to exceed the service limit state established in the 2010 AASHTO LRFD Bridge Design Specifications in the case of the California bridge.

The exposure from a localized vehicle fire has been observed to produce excessive damage onto highway bridge structural elements including complete collapse of the infrastructure. The occurrence of a fire beneath a bridge can lead to significant economic expense and loss of service even if the bridge does not collapse. The focus of the current research is to assess and evaluate the effect of realistic localized fire exposures from vehicles on the bridge structural integrity and to guide future development of highway bridge design with improved fire resistance. In this research, the bridge structural element response was predicted through a series of three loosely coupled analyses: fire analysis, thermal analysis, and structural analysis. Two different types of fire modeling methodologies were developed in this research and used to predict the thermo-structural response of bridge structural elements: one to model the non-uniform exposure due to a vehicle fire and another to predict response due to a standard uniform furnace exposure. The vehicle fire scenarios required coupling the computational fluid dynamics (CFD) code Fire Dynamics Simulator (FDS) with Abaqus while the furnace exposure scenarios were all done within Abaqus. Both methodologies were benchmarked against experimental data. Using the developed methodologies, simulations were initially performed to predict the thermo-structural response of a single steel girder-concrete deck composite assembly to different local, non-uniform fires and uniform standard furnace fire exposures. The steel girder-concrete deck composite assembly was selected since it is a common bridge design. Following this, a series of simulations were performed on unprotected highway bridges with multiple steel plate girders and steel tub girders subjected to localized fires. The analyses were used to evaluate the influence of a fire scenario on the bridge element response, identify the factors governing the failure of bridge structural elements subjected to a localized fire exposure, and provide guidance in the design of highway bridge structural elements against fire hazards. This study demonstrates that girder geometry affected both the dynamics of the fire as well as the heat transfer to the bridge structural elements which resulted in a different structural response for the bridge. A heavy goods vehicle (heat release rate of 200 MW) and tanker fires (heat release rate of 300 MW) were predicted to cause the bridge to fail due to collapse, while smaller fires did not. The geometric features of the plate girders caused the girder elements to be exposed to higher heat fluxes from both sides of the girder resulting in collapse when exposed to a HGV fire. Conversely, the closed feature of the box girder does not allow the interior surfaces to be in direct contact with the flames and are only exposed to the internal reradiation from surfaces inside the girder. As a result, the single and double lane tub girder highway bridge structure does not fail due to a heavy goods vehicle fire exposure. / Ph. D.

By its nature a spliced girder must contain a number of post tensioning tendons throughout its length. The focus of the experimental program described in this dissertation is the evaluation of the strength and serviceability of post-tensioned girders loaded in shear, and, more specifically, how a post-tensioning duct located in the web of a girder affects the shear transfer mechanism of a bulb-tee cross-section. Due to the limited number of tests in the literature conducted on full-scale post-tensioned girders, eleven shear tests were performed on seven prestressed concrete bulb-tee girder specimens. Of these tests, ten were conducted on specimens that contained a post-tensioning duct within their web and additional pretensioning reinforcement in their bottom and top flanges. The remaining shear test was conducted on a control specimen that did not have a post-tensioning tendon but contained the same pretensioning reinforcement as the post-tensioned girder specimens. The behavioral characteristics of these eleven test specimens at service level shear forces and at their ultimate shear strengths were evaluated in regards to five primary experimental variables: (i) the presence of a post-tensioning duct, (ii) post-tensioning duct material (plastic or steel), (iii) web-width, (iv) duct diameter, and (v) the transverse reinforcement ratio. The findings of this experimental study are described in detail within this dissertation, but can be summarized by the following two points. (i) No differences were observed in the ultimate or service level shear behavior in girders containing plastic grouted ducts when compared to those containing steel grouted ducts and (ii) The current procedure of reducing the effective web width to account for the presence of a post-tensioning duct is ineffective because it addresses the incorrect shear transfer mechanism. A method that correctly addresses the reduction in shear strength due to the presence of a post-tensioning duct was developed and verified using the tests performed during this experimental program and tests reported in the literature. / text

In April of 2008, the Federal Highway Administration (FHWA) launched the Long Term Bridge Performance (LTBP) program. The program was established to collect scientific quality data from a number of bridges across the nation over a period of 20 years. The data will be used to provide a better picture of bridge health and structural performance. Utah Department of Transportation (UDOT) structure number 1F 205, located 2.4 km (1.5 mi) west of Perry, Utah, was selected as one of the LTBP pilot bridges (this bridge will also be referred to as the Cannery Street Overpass). UDOT performs regular maintenance on this bridge and in April of 2011 they began a rehabilitation project over a 13-km (8-mi) section of I-15 that included the Cannery Street Overpass. The main purpose of this rehabilitation was to improve pavement conditions. As part of this work, in the fall of 2011 UDOT removed all of the asphalt from the bridge deck, performed deck repairs, and placed a new asphalt layer. A unique opportunity presented itself to better understand the relationship between the mass and resonant vibration frequencies of the structure. This relationship is understood by (omega_n)^2=k/m, where omega_n=resonant frequency; k=stiffness; and m=mass. A decrease in mass should yield an increase in resonant frequency. Dynamic testing was done on the bridge to obtain its resonant frequencies. This testing included measuring the velocity response of the structure at different points on the bridge due to ambient vibrations (mainly from traffic). Three tests were performed before, during, and after UDOT's scheduled maintenance. These testing states include: State 1. Original asphalt on bridge deck State 2. No asphalt on bridge deck State 3. New asphalt on bridge deck These three states represent three different mass states of the bridge. The original asphalt layer was substantially heavier than the new asphalt layer. The data obtained from all three tests was processed in order to extract modal properties of the bridge. The changes in modal properties were analyzed and the results of the testing proved to be insightful at defining the relationship between mass and resonant frequency.

This study addresses the development of a prototype software system for analysis of horizontally curved steel I-girder bridges using open-section thin-walled beam theory. Recommendations are provided for the use of three-dimensional (3D) grid idealizations in analyzing curved I-girder bridge structural systems. The 3D grid idealizations account for the general displacements and rotations common within complex curved I-girder bridge structures, i.e., none of the displacement and rotational degrees-of-freedom are arbitrarily assumed to be equal to zero. Also, these idealizations account for the warping (or cross-bending) deformations of the I-girder flanges that dominate typical girder torsional responses. An approximate approach is investigated for capturing the influence of girder web distortion on composite I-girder responses. A key focus of this research is the development of prototype methods for simulating the construction of curved steel I-girder bridges, including erection of the steel and staged casting of the slab. The resulting capabilities allow engineers to evaluate the deflections, reactions and/or stresses at different stages of the steel erection or concrete slab construction, determine required crane capacities, tie-down, jacking or come-along forces, and calculate incremental displacements due to removal of temporary supports. Also, the capabilities can be used to determine the influence of different steel detailing methods on the bridge geometry, such as the web plumbness under the steel or total dead load. Key requirements necessary to ensure accuracy of the analysis results are addressed.

The torsional rigidity of tub-girder makes them ideal for use in curved bridges. The use on skewed support applications by bridge designers is limited as the behavior is complex and requires the use of advanced analysis tools. In consequence, a simplified analysis method to account for the effects of skew on tub-girder twist rotations and internal torques and how these affect the internal component forces was proposed. The combined effects of skew and curvature are studied by examining the results for analysis with different levels of sophistication for 18 representative bridges. The data generated constitutes the first systematic study on a large set of curved and skewed tub-girder bridges using consistent, refined 3D FEA models to model construction forces and deformations. Comparisons of the simplified analysis method to the refined 3D FEA analysis display the limitations of the simplified analysis and present potential sources of error. Furthermore, the results from the 3D FEA helped identify interactions between components and, therefore, an improved simplified procedure was proposed to account for the effects of the resulting increased stresses. In addition, the bridge erection procedures are discussed and specific examples illustrating the calculation of the fit-up forces is presented. These findings provided additional tools for the analysis process and erection engineering to account for the effects of skew. Lastly, further research needs considering the analysis of additional loading conditions and construction procedures are described.

Thesis (Ph. D.)--University of Texas at Austin, 2001. / Vita. Includes bibliographical references. Available also from UMI/Dissertation Abstracts International.

Prestressed concrete construction relies on the application of compressive stresses to concrete elements. The prestressing force is typically applied through the tensioning of strands that react against the concrete and induce compression in the concrete. Loss of prestress is the decrease of this pre-applied stress. The conservative estimation of the prestress losses is imperative to prevent undesired cracking of the prestressed element under service loads. A large fraction of the prestress losses is a consequence of concrete deformations. This fraction of the losses can be identified as strain-related losses, and these occur due to instantaneous elastic shortening, and time-dependent creep and shrinkage. Creep and shrinkage of concrete depend on many factors that are extremely variable within concrete structures. The time-dependent behavior of concrete is not well-understood, but recent findings in the topics of concrete creep and shrinkage provide a better understanding of the underlying mechanisms affecting the nature of these two phenomena. However, current design practices and prestress loss estimation methods do not reflect the state-of-the-art knowledge regarding creep and shrinkage. The main objective of this dissertation was the study and estimation of strain-related prestress losses in simply supported pretensioned bridge girders. Simply supported pretensioned girders are widely designed, produced and frequently used in bridge construction. Due to this common use, pretensioned concrete bridge girders has become fairly standardized elements, which results in a reduced variability in the behavior of pretensioned bridge girders, as compare to that of less standardized concrete structures. Hence, a simplified method was calibrated to estimate prestress losses within pretensioned girders to an adequate level of accuracy. To achieve an acceptable accuracy experimental data from the monitoring of pretensioned simply supported girders was used for the calibration of the method. The accuracy of this simplified method is comparable to that achievable using more elaborate methods developed for generic concrete structures. / text

Not available / text

No description available.