No description available.

No description available.

No description available.

As clean energy demand is on the rise and the wind energy sector in growth, locations with the highest wind potential are becoming of higher interest for wind farm projects, but they are located in colder regions. In cold climates, ice accumulation on wind turbine blades is a serious issue, both in terms of safety and performance. To prevent this, anti-icing technologies, such as Vestas Wind Systems A/S’s, electro-thermal elements are added to wind turbine blades’ construction. This thesis project consists of developing a method to investigate the heat transfer inside and out of wind turbine blades to assess the performance of the anti-icing system and most importantly, verify if it could lead to thermal damage of the blade’s adhesive. In an integrated MATLAB code, the heating requirement is calculated and the 2D conduction modelled based on the wind conditions. The output is a temperature map of the internal structure along with the points with the highest temperature for all adhesive locations, which shows that the selected heating power provided by the heating elements compromises the integrity of the adhesive and doesn’t perform to allow the surface temperature to reach the necessary threshold the prevent icing.

A series of random and amorphous copolyesters containing different cycloaliphatic rings within the polymer chains were prepared by melt polycondensaton of difunctional monomers (diesters and diols) in the presence of a catalyst. These polyesters were characterized by nuclear magnetic resonance (NMR), size exclusion chromatography (SEC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), tensile tests and/or dynamic mechanical analysis (DMA). The copolyester based on dimethyl bicyclo[2.2.2]octane-1,4-dicarboxylate (DMCD-2) was observed to have a higher Tg, about 115ºC, than the other copolyesters with the same compositions in this study. For copolyesters containing different compositions of dimethyl-1,4-cyclohexane dicarboxylate (DMCD) and DMCD-2, the Tg increased linearly with the increase of DMCD-2 mole content. DMA showed that all of the cycloaliphatic copolyesters had secondary relaxations, resulting from conformational transitions of the cyclohexylene rings. The polyester based on DMCD-3 in the hydrolytic tests underwent the fastest hydrolytic degradation among these samples. A new triptycene diol (TD) was synthesized and incorporated into a series of cycloaliphatic copolyester backbones by melt condensation polymerization. Straight chain aliphatic spacers, including ethylene glycol (EG), 1,4-butanediol (BD) and 1,6-hexanediol (HD), were used as co-diols to explore their effects on polyester properties. An analogous series of non-triptycene copolyesters based on various hydroxyethylated bisphenols were also prepared for comparison. The results revealed that the TD-containing polymers had higher thermal stability and higher Tg's than the corresponding non-TD analogs. For TD-containing copolyesters, the mechanical properties were found to be dependent on the types and compositions of the co-diols. A 1,4-butanediol-based triptycene copolyester was observed to have a significantly increased Tg and modulus while maintaining high elongation at ambient temperature. Furthermore, it was demonstrated that the triptycene polyester exhibited higher Tg and modulus than those containing bisphenol derivatives. However, all of the 1,4-butanediol based copolyesters were brittle and had comparable moduli at low temperatures (-25°C or -40 °C). Melt polycondensation was also used to prepare a series of all-aliphatic block and random copolyesters including the following aliphatic monomers: trans-DMCD, DMCD-2, neopentyl glycol (NPG), diethylene glycol (DEG) and dimethyl succinate (DMS). The polymer compositions were determined by 1H NMR, and the molecular weights were determined using SEC. The polyesters were also characterized by TGA, DSC, DMA and tensile tests. Phase separation was not observed in these block copolyesters. However, the block copolyester containing DMCD-2 and NPG was observed to have a higher Tg than the block copolyester based on trans-DMCD and NPG. In addition, these block copolyesters were found to have better mechanical properties than the corresponding random copolyesters. / Ph. D.

This study is an evaluation of epoxy coated reinforcing steel (ECR) and its ability to effectively provide corrosion protection in reinforced concrete highway bridge decks. An analysis was conducted on 10 bridge decks built in the state of Virginia between the years 1981 and 1995. A total of 141 cores containing either ECR or bare steel were evaluated. A chloride solution was applied to the surface on a weekly cycle (for a total duration of 3.06 years) and a nondestructive electrochemical testing was performed on each core on a monthly cycle. Cores were also inspected for surface cracks, the thermal properties of the epoxy coating, and the concrete conditions at bar depth. The concrete was tested for saturation percentages, diffusion coefficients, and chloride contents, while the epoxy was tested for its glass transition temperature, moisture content, and amount of surface cracking. The results indicate that the best predictor for estimating the times to corrosion initiation and cracking is the amount of chlorides present in the concrete encasing the ECR. The presence of chloride ions will have a determining effect on corrosion regardless of the epoxy coating condition. As a result, it is likely that ECR is not the solution to corrosion prevention and it is recommended that closer attention be given to improving concrete conditions that reduce the diffusion of chloride ions. The conclusion that ECR is an unreliable corrosion prevention method is in agreement with the results of previous studies. / Master of Science

Rotational-translational decoupling, a phenomenon commonly observed in supercooled liquids, has been a topic of great interest. Despite its prevalence, the underlying cause of this phenomenon, often attributed to dynamic heterogeneity, has not been conclusively elucidated. This thesis investigates and evaluates how dynamic heterogeneity may lead to this decoupling using simultaneous single-molecule rotational and translational measurements. In the experimental study, single molecule fluorescence imaging experiments are performed on the ideal probe N,N’-dipentyl-3,4,9,10-perylenedicarboximide in high molecular weight polystyrene near its glass transition temperature. A novel trajectory linking method based on hierarchical clustering is developed to facilitate single molecule tracking even in imaging data where specific molecules cannot be observed visually for a substantial number of frames. This linking algorithm then allows molecules to be localized over full movies, such that rotational and translational measurements can be compared over comparable timespans. The investigation of translational dynamics using such long trajectories, which was not previously achieved, reveals that both rotational-translational decoupling and translational enhancement persist on the single molecule level, supporting the hypothesis that temporally heterogeneous dynamics experienced by the probe molecules is a contributing factor in observed rotational-translational breakdown in both ensemble and single molecule studies. A tendency towards dynamical convergence between subgroups with fast and slow dynamics is observed, demonstrating temporal heterogeneity at the single molecule level. In comparison to rotational dynamics, translational dynamics was discovered to have a longer lifetime. Other key observations facilitated by the linked trajectory analysis include that apparent diffusion coefficient of probe molecules decreases with longer observation time, a finding inconsistent with normal diffusive behavior. To investigate the origin of this anomalous slowing in single molecule studies existing alongside the observed overall enhancement in translational motion, temporally heterogeneous models with multiple types of correlation were studied via simulations. The results emphasize the critical role that bias in translational and rotational measurements can play when investigating and observing dynamic heterogeneity, as nearly all models including dynamic heterogeneity show increasing diffusion coefficient with increasing number of dynamic environments explored. Strikingly, translational enhancement is evident in single molecule translational simulations even when slow dynamics are reinforced via positive correlation in the models. A comparison of the diffusion coefficient evolution between simulations and experiments reveals that the sub-diffusive continuous time random walk model is the most plausible candidate to account for the set of observations seen in experiment.

The focus of this dissertation was to investigate the influence of sidechain structure and sidechain content on the morphology and physical properties of perfluorosulfonic acid ionomer (PFSA) membranes. One of the primary objectives was to characterize the thermomechanical relaxations for short sidechain PFSAs developed by 3M and Solvay, as well as a new multi-acid sidechain perfluoroimide acid ionomer (PFIA) from 3M. Partial neutralization experiments played a key role in systematically manipulating the strength of the electrostatic interactions between proton exchange groups on each sidechain, leading to the elucidation of the molecular-level motions associated with multiple thermal relaxations observed by dynamic mechanical analysis (DMA). Particularly, 3M PFSA and Solvay Aquivion lack an observable β-relaxation in the sulfonic acid-form that is observed in the long sidechain PFSA, Nafion. By varying the strength of the physically-crosslinked network through exchanging the proton on the sulfonic acid groups for large counterions, we were able to conclude that the shorter sidechain length and increase in ion content in the 3M PFSA and Solvay Aquivion serves to restrict the mobility of the polymer backbone such that the onset of segmental motions of the main chains is not observed at temperatures below the α-relaxation temperature, where destabilization of the physically crosslinked network occurs. As a complementary technique to DMA for probing the relaxations in PFSAs, we introduced a new pretreatment method for differential scanning calorimetry (DSC) measurements that uncover a thermal transition in H+-form 3M PFSA, Aquivion, and Nafion membranes. This thermal transition was determined to be of the same molecular origin as the dynamic mechanical α-relaxation temperature in H+-form PFSAs, and the β-relaxation temperature in tetrabutylammonium (TBA+)-form PFSAs. The thermomechanical relaxations in multi-acid sidechain 3M PFIA were also investigated. Interestingly, the additional acidic site on PFIA led to unexpected differences in thermal and mechanical properties, including the appearance of a distinct glass transition temperature otherwise not seen in PFSA ionomers. We utilized small-angle X-ray scattering (SAXS) studies to probe the differences in aggregate structure between the PFIA and PFSA membranes in order to uncover the morphological origin of the anomalous thermomechanical behavior in PFIA membranes. Larger aggregate structures for PFIA, compared to PFSA, incorporate intervening fluorocarbon chains within the aggregate, resulting in increased spacing between ions that reduce the collective electrostatic interactions between ions such that the onset of chain mobility occurs at lower temperatures than the α-relaxation for PFSA. The SAXS profiles of PFSAs showed two scattering features resulting from scattering between crystalline domains and ionic domains distributed throughout the polymer matrix. In order to fit the "ionomer peak" to models used for the PFIA and PFSA aggregate structure determination, we presented a method of varying the electron density of the ionic domains by using different alkali metal counterions as a tool to make the intercrystalline feature indistinguishable. This allows for isolation of the ionomer peak for better fits to scattering models without any interference from the intercrystalline peak. Lastly, an investigation of annealing PFSAs of different sidechain structures in the tetramethylammonium (TMA+) counterion form above their α-relaxation showed a profound crystalline-like ordering of the TMA+ counterions within the ionic domains. This ordering is maintained after reacidification and leads to improved proton conductivity, which indicates that this method can be used as a simple processing method for obtaining improved morphologies in proton exchange membranes for fuel cell applications. / Doctor of Philosophy / Hydrogen fuel cells offer an environmentally friendly, high efficiency method for powering vehicles, buildings, and portable electronic devices. At the center of a hydrogen fuel cell is a polymer membrane that contains ionic functionalities, which conduct hydrogen ions (protons) from the anode to the cathode while preventing conduction of electrons. The electrons travel through an external circuit to produce electricity, while the protons travel through the polymer membrane and meet with oxygen on the other side to produce water, the only byproduct of a hydrogen fuel cell. The efficiency of this process relies on the ability of the polymer membrane to conduct protons, and the lifetime of a fuel cell depends on the mechanical stability of this membrane. Perfluorosulfonic acid ionomers are good candidates for use as polymer membranes in hydrogen fuel cells due to their Teflon backbone that provides mechanical stability and their sulfonic acid functionalities that form channels for proton conduction. In this work, we probe the structure-property relationships of different perfluorosulfonic acid ionomers for use as fuel cell membranes. We focus on thermal analysis techniques to develop a fundamental understanding of the effect of chemical structure and sulfonic acid content on the temperature-induced mobility of the polymer chains in these ionomers. This mobility at elevated temperatures can be utilized to rearrange the morphological structure of perfluorosulfonic acid ionomer membranes in order to enhance proton conductivity and mechanical integrity.

In 2012, a new type of lignin, catechyl (C)-lignin was found in the seed coat of vanilla orchid (Vanilla planifolia) and Melocactus cacti, and later in the nutshell of Aleurites moluccana (candlenut). This caffeyl alcohol homopolymer is the exclusive lignin in vanilla seed coat but separated in time and/or location with guaiacyl (G)-lignin in candlenut. Unlike conventional guaiacyl/syringyl (G/S-lignins) with alkyl-aryl ether linkages, intermonomer linkages in C-lignin are connected by benzodioxane linkages which are stiffer than alkyl-aryl ether linkages. C-lignin is unusually stable against acid-catalyzed cleavage. Tissues with C-lignin are expected to exhibit high glass transition temperature (Tg) compared to tissues with G/S/H-lignin. C-lignin also probably shows high crystallinity due to its highly linear-homopolymer structure. The ability of some seed coats/nutshells in angiosperms to synthesize a new type of lignin is another level of lignin evolution. However, the role of C-lignin related to the function of the seed coat is unclear while it exhibits different behaviors to the regular G/S/H-lignin. These points motivated us to conduct cell-wall structure/property studies in the context of plant evolution, using microscopy, X-ray diffraction (XRD) and dynamic mechanical analysis (DMA). Light and electron microscopes were used to identify cell's size and type of intact and macerated vanilla seed coat and candlenut shell. Vanilla seeds are tiny, sized approximately 300μm and the surface is covered with dark-colored seed coat. Candlenut is slightly smaller than walnut, with uneven, hard, dark brown shell covering the nut. Microscopy observations indicated that both seed coat and nutshell are dominated by highly lignified cells, known as sclereids. The types of sclereids in vanilla seed coat and candlenut shell are different; vanilla seed coat has ostoesclereid-type cells, while candlenut shell has macrosclereid-type cells. XRD was used to study tissue with C-lignin crystallinity by comparing diffractograms of vanilla seed coat and candlenut shell to Southern Yellow Pine wood diffractograms. The Southern Yellow Pine wood diffractogram corresponds to a typical native cellulose in higher plants, that is cellulose I allomorph. Diffractogram XRD analysis on vanilla seed coat and candlenut shell shows similarities to Southern Yellow Pine native cellulose, suggesting that cellulose is the contributor for crystallinity in seed coat and nutshell, and this also indicated that tissues with C-lignin is not crystalline. Crystallinities of vanilla seed coat and candlenut shell determined using peak deconvolution methods were about half of Southern Yellow Pine crystallinity. DMA was used to measure Tg in vanilla seed coat and candlenut shell. Measurements were conducted in solvent-submersion mode using organic plasticizers to reduce the Tg to non-damaging temperatures. DMA measurement of vanilla seed coat and candlenut shell is challenging due to specimen size and shape. Specimen preparation for DMA measurement included seed coat purification for vanilla and cutting/milling for candlenut shell followed by specimen saturation in plasticizers. Compressive-torsion DMA was used to allow tiny specimens gripping. Vanilla seed coats exhibited higher glass transition temperature compared to wood, while candlenut shells exhibited various Tgs depending on specimen type/size. / Doctor of Philosophy / Lignin is a complex organic material that constructs higher plant cell walls. Lignin provides stiffness and strength and is the landmark of plant evolution to terrestrial life. Typically, lignin in hardwood/softwood has guaicayl and/syringyl (G/S) units derived from coniferyl/sinapyl alcohols. ln 2012, a new type of lignin, catechyl (C)-lignin, was found in the seed coat of vanilla orchid (Vanilla planifolia) and Melocactus cacti, and later in the nutshell of Aleurites moluccana (candlenut). C-lignin is a caffeyl alcohol homopolymer and is exclusive in vanilla seed coat but coexists with guaiacyl (G)-lignin in candlenut shells. This new type of lignin exhibits different behavior than G/S-lignin. C-lignin is unusually stable against acid-catalyzed hydrolysis. Intermonomer linkage in C-lignin is stiffer than G/S lignin(s); it is likely to have higher glass transition temperature (Tg) than normal lignin. Due to its linearity, tissue with C-lignin is also expected to be highly crystalline. C-lignin's roles are not well known and therefore, these are merit for structure/property studies in the context of plant evolution as bio-inspired new materials. Microscopy, X-ray diffraction (XRD), and dynamic mechanical analysis (DMA) were used to study vanilla seed coat and candlenut shell morphology, crystallinity, and glass transition temperatures (Tg), respectively. It was observed that the two tissues have different types of sclereids, but this is not associated with why vanilla seed coats exhibit only C-lignin while candlenut shells have both C /G-lignins. XRD scans revealed that C-lignin is not crystalline due to similarity of their diffractograms to those of wood. DMA measurements revealed that vanilla seed coat tissues exhibit higher Tg than tissue with G/S lignin as expected, while the Tg candlenut shells varied among specimen type and particle sizes.

The focus of this research project was to investigate morphological and mechanical properties of both extruded and dispersion-cast Nafion® membranes. The project can be divided into three primary objectives; obtaining a fundamental understanding of the glass transition temperature of Nafion®, determining the effect of thermal annealing treatments on the morphology and mechanical properties of dispersion-cast Nafion®, and examination of dispersion-cast Nafion® subjected to an ex-situ, Fenton's chemical degradation test. Nafion®, a perfluorosulfonate ionomer, is considered a commercially successful semi-crystalline ionomer with primary applications in chlor-alkali cells and proton exchange membrane fuel cells. With the aid of dynamic mechanical analysis (DMA) and dielectric spectroscopy (DS), we were able to provide definitive evidence for a genuine glass transition in Nafion®. DMA of Nafion® samples that were partially neutralized with tetrabutylammonium counterions showed a strong compositional dependence suggesting that the β-relaxations of H+-form Nafion® and the neutralized ionomers have the same molecular origin with respect to backbone segmental motions. Building upon our previous studies of the molecular and morphological origins of the dynamic mechanical relaxations of Nafion® neutralized with a series of organic ions, the glass transition temperature of H+-form Nafion® is now confirmed to be the weak β-relaxation centered at -20 °C. Dielectric spectra also showed this transition from the perspective of dipole relaxation. The signature of cooperative long range segmental motions in dielectric spectra was seen here, as with other polymers, mainly through the excellent agreement of the β-relaxation time-temperature dependence with the Vogel-Fulcher-Tammann equation. We have also discovered that new dispersion-cast H+ form Nafion® membranes are susceptible to disintegration/dissolution when subjected to boiling methanol. In this work, we have achieved significant decreases in the percent solubility of H+-form Nafion® by either thermally annealing above 175 °C or solution-processing at 180 °C using a high boiling point solvent. Small Angle X ray Scattering (SAXS) displayed a change in the morphology of H+ form membranes with increasing annealing temperature by a shift in the crystalline scattering peak (q â 0.05 Ã 1) to lower q values. Counterion exchange of Nafion® from H+ to Na+ form had no influence on the membrane's susceptibility to disintegration in boiling methanol. In order to achieve mechanical stability in boiling methanol, Na+ form membranes had to be annealed at 275 °C for at least fifteen minutes. The SAXS data of annealed Na+ form membranes showed a dramatic decrease in crystalline order with annealing temperature, ultimately leading to the disappearance of the crystalline scattering peak after fifteen minutes at 275 °C. The onset of methanol stability with the melting of Nafion® crystallites suggests that chain entanglement is an important parameter in obtaining solvent stability. With respect to chemical stability, we performed studies aimed at examining the effects of Fenton's Reagent on the resistance to radical attack of new generation, dispersion-cast Nafion®. Changes in the 19F solid-state NMR spectra of dispersion-cast Nafion® before and after chemical degradation via Fenton's Reagent predicts a rather random attack by ·OH and ·OOH radicals. Several membranes were also thermally annealed between 100-250 °C in an attempt to correlate crystallinity with chemical degradation kinetics of Nafion® via Fenton's Reagent. The results indicate that the effect of counterion exchange into the Na+ form was minimal, but the degree of thermal degradation had a tremendous effect on the fluoride release rate and chemical degradation kinetics. By exchanging the membranes into the Na+ form, thermal degradation was avoided, allowing us to study the role of crystallinity as a function of fluoride release. Ultimately, Nafion® crystallinity was deemed an important factor in deterring peroxide radical attack. As the percent crystallinity decreased with annealing temperature, the fluoride concentration in the resulting Fenton's media increased accordingly, indicating that the amorphous regions of the polymer are more susceptible to chemical degradation via peroxide radical attack. / Ph. D.