Sistemas de transmissão de energia elétrica em corrente contínua e alta tensão baseados em tecnologia de conversores a fonte de tensão (VSC-HVDC), ao contrário de linhas de transmissão em corrente alternada, operam como elementos de controle de variáveis elétricas, podendo ser úteis na estabilidade do sistema de potência. Mas apesar desta vantagem, sistemas VSC-HVDC possuem limitações no desempenho estável, o que enseja o desenvolvimento de uma metodologia para mapeamento de suas zonas de operação estável e possíveis regiões de instabilidade. Inicialmente estudou-se os detalhes da tecnologia VSC-HVDC tais como o funcionamento da eletrônica de potência e estratégias de controle utilizadas. Em seguida, investigou-se os modelos de geradores síncronos para interconexão com o lado CA das estações conversoras do VSC-HVDC. E, finalmente, aplicou-se a tecnologia VSC-HVDC sobre um modelo de sistema de potência com uma estação conversora localizada em um porto offshore e uma outra no continente, próxima à rede de alta tensão em corrente alternada. Simulações e análise deste sistema foram executadas considerando várias condições operacionais. O gráfico de potência gerada e consumida, obtido pela aplicação da metodologia, apresenta grande potencial de uso prático como por exemplo sua implementação na interface homem-máquina da estação de operação do porto offshore, provendo informação em tempo real de alto nível ao operador do sistema elétrico do porto offshore e consequentemente aumentando sua consciência situacional quanto a proximidade dos limites de instabilidade. / High voltage direct current power transmission systems based on voltage source converters (VSC-HVDC), as opposed to alternating current ones, operates as elements of control of electrical variables, being useful for stability of power system. Besides this advantage, VSC-HVDC systems have limitations in stable performance, which instigates the development of a methodology for mapping its operational zones of stability and possible regions of instability. The author initially studied the details of the VSC-HVDC technology such as the power electronic principles and the control strategies used on this research. Subsequently, the author investigated synchronous generator models for interconnection on the AC side of the VSC-HVDC converter stations. Finally, the author applied the VSC-HVDC technology on a model of power system with two converter stations, one located on an offshore port and the other on the shore, next to an alternating current high voltage power grid. Simulations and analysis of this system were carried out considering various operational conditions. The graphic of generated and consumed power on offshore port, obtained by the application of the methodology for mapping operational zones, presents a great potential of being implemented in the man-machine interface of an operation workstation, thus providing high level online information for the operator of the offshore port electrical system and consequently improving its situational awareness of the proximity to instability limits.

Sistemas de transmissão de energia elétrica em corrente contínua e alta tensão baseados em tecnologia de conversores a fonte de tensão (VSC-HVDC), ao contrário de linhas de transmissão em corrente alternada, operam como elementos de controle de variáveis elétricas, podendo ser úteis na estabilidade do sistema de potência. Mas apesar desta vantagem, sistemas VSC-HVDC possuem limitações no desempenho estável, o que enseja o desenvolvimento de uma metodologia para mapeamento de suas zonas de operação estável e possíveis regiões de instabilidade. Inicialmente estudou-se os detalhes da tecnologia VSC-HVDC tais como o funcionamento da eletrônica de potência e estratégias de controle utilizadas. Em seguida, investigou-se os modelos de geradores síncronos para interconexão com o lado CA das estações conversoras do VSC-HVDC. E, finalmente, aplicou-se a tecnologia VSC-HVDC sobre um modelo de sistema de potência com uma estação conversora localizada em um porto offshore e uma outra no continente, próxima à rede de alta tensão em corrente alternada. Simulações e análise deste sistema foram executadas considerando várias condições operacionais. O gráfico de potência gerada e consumida, obtido pela aplicação da metodologia, apresenta grande potencial de uso prático como por exemplo sua implementação na interface homem-máquina da estação de operação do porto offshore, provendo informação em tempo real de alto nível ao operador do sistema elétrico do porto offshore e consequentemente aumentando sua consciência situacional quanto a proximidade dos limites de instabilidade. / High voltage direct current power transmission systems based on voltage source converters (VSC-HVDC), as opposed to alternating current ones, operates as elements of control of electrical variables, being useful for stability of power system. Besides this advantage, VSC-HVDC systems have limitations in stable performance, which instigates the development of a methodology for mapping its operational zones of stability and possible regions of instability. The author initially studied the details of the VSC-HVDC technology such as the power electronic principles and the control strategies used on this research. Subsequently, the author investigated synchronous generator models for interconnection on the AC side of the VSC-HVDC converter stations. Finally, the author applied the VSC-HVDC technology on a model of power system with two converter stations, one located on an offshore port and the other on the shore, next to an alternating current high voltage power grid. Simulations and analysis of this system were carried out considering various operational conditions. The graphic of generated and consumed power on offshore port, obtained by the application of the methodology for mapping operational zones, presents a great potential of being implemented in the man-machine interface of an operation workstation, thus providing high level online information for the operator of the offshore port electrical system and consequently improving its situational awareness of the proximity to instability limits.

Ao buscar alternativas para interligação entre importantes centros de geração de energia elétrica localizados no Norte do Brasil e centros consumidores no Nordeste e Sudeste, o setor elétrico brasileiro se depara com o desafio de transpor distâncias superiores a 2000 km. A alternativa em corrente contínua já é bastante utilizada, com desempenho satisfatório. Já a transmissão em meia-onda, ainda não utilizada comercialmente em país algum do mundo, é uma alternativa sugerida por alguns artigos como adequada a esse propósito. Este trabalho se propõe a apresentar uma metodologia de comparação econômica entre alternativas de transmissão e aplicá-la à comparação entre a meia-onda e a corrente contínua, utilizando um cenário muito próximo ao brasileiro. Para possibilitar esta comparação, são apresentados detalhes do funcionamento da linha de meia-onda, já que pouco foi publicado sobre o assunto. São mencionados alguns aspectos adversos de seu comportamento transitório e também são descritas etapas de definição de alternativas de transmissão a serem avaliadas. / In order to connect important power generation plants located in Northern region to the major load centers in the Northeast and Southeast parts of the country, the Brazilian electric sector should deal with the challenge of planning transmission systems to cover distances of more than 2000 km. The HVDC transmission alternative, which has shown satisfactory response and performance to also carry bulk power over long distances, is already used in many countries. Still, the half-wavelength power transmission line (HWLL), not yet commercially used in any country, is an alternative suggested by some papers as suitable for this purpose. Thus, the objective of this work is to present a methodology for the economic comparison amongst the transmission alternatives present today, to thereafter apply it to the HWLL and HVDC transmission technologies. To do so, a closest scenario to that of the Brazilian case will be used. In order to perform this comparison, some details of the HWLL operation are explored, since little was published on this subject. Also, some adverse aspects of the HWLL transient behavior as well as the steps for defining the transmission alternatives to be evaluated are presented.

The interaction of an HVDC converter with the connected power system is of complex nature. An accurate model of the converter is required to study these interactions. The use of analytical small-signal converter models provides useful insight and understanding of the interaction of the HVDC system and the connected system components. In this thesis analytical models of the HVDC converters are developed in the frequency-domain by calculating different transfer functions for small superimposed oscillations of voltage, current, and control signals. The objective is to study the dynamic proprieties of the combined AC-DC interaction and the interaction between different HVDC converters with small signal analysis. It is well known that the classical Bode/Nyquist/Nichols control theory provides a good tool for this purpose if transfer functions that thoroughly describe the 'plant' or the 'process' are available. Thus, there is a need for such a frequency-domain model. Experience and theoretical calculation have shown that voltage/power stability is a very important issue for an HVDC transmission link based on conventional line-commutated thyristor-controlled converters connected to an AC system with low short circuit capacity. The lower the short circuit capacity of the connected AC system as compared with the power rating of the HVDC converter, the more problems related to voltage/power stability are expected. Low-order harmonic resonance is another issue of concern when line-commutated HVDC converters are connected to a weak AC system. This resonance appears due to the presence of filters and shunt capacitors together with the AC network impedance. With a weak AC system connected to the HVDC converter, the system impedances interact through the converter and create resonances on both the AC- and DC-sides of the converter. In general, these resonance conditions may impose limitations on the design of the HVDC controllers. In order to improve the performance of the HVDC transmission system when it is connected to a weak AC system network, a reactive compensator with a voltage source converter has been closely connected to the inverter bus. In this thesis it is shown that the voltage source converter, with an appropriate control strategy, will behave like a rotating synchronous condenser and can be used in a similar way for the dynamic compensation of power transmission systems, providing voltage support and increasing the transient stability of the converter. / QC 20100708

In this thesis, a new HVDC-based converter system for wind farms is investigated. It is based on a mutually commutated soft-switching converter system and provides a unique integrated solution for the wind turbine generator drive systems, the wind turbine interconnection, and the power conversion for HVDC transmission. In a wind farm, the mutually commutated converter system is a distributed system. A medium-frequency collection grid connects the converter station, equipped with a single-phase voltage source converter and a medium-frequency transmission transformer, with the wind turbines, each containing a cycloconverter and a medium-frequency distribution transformer. In this thesis, various system aspects regarding the application of a distributed mutually commutated converter system in a wind farm are investigated. Special attention is paid to the design of a medium-frequency collection grid that has an acceptable level of transient overvoltages, the design of medium-frequency transformers with suitable magnetic, electric and thermal properties, and the development of a strategy to commutate the voltage source converter during low power generation. In order to adapt the mutually commutated converter system for an application in a wind farm, it had to be further developped. Different carrier-based and space-vector oriented modulation methods have been investigated. It turns out that for any load angle there is a quasi-discontinuous pulse width modulation strategy that can produce the same pulse patterns as space vector modulation. In addition, a modulation strategy has been developed that allows to replace the IGBTs in the cycloconverter with cheap, robust, and reliable fast thyristors, despite their absence of turn-off capability. The feasibility of different modulation strategies for mutually commutated converter systems has been verified on a down-scaled prototype converter system with both IGBT- and thyristor-based cycloconverters. Finally, a feasible wind farm layout is proposed, which considerably reduces the energy generation costs for large winds farms distant to a strong grid connection point. As a consequence, the proposed solution may facilitate the establishment of remotely located wind farms. / QC 20100802

Outdoor insulators are one of the most important parts of a power system. The reliability of a power system depends also on the reliability of the insulators. The main functions of an insulator used for outdoor applications are to give the necessary insulation, provide the necessary mechanical support to the transmission line conductor and also to resist the various environmental stresses like pollution, ultra violet rays etc. Traditionally porcelain and glass insulators have been used for outdoor insulator applications. They are good insulators under normal conditions and the cap and pin arrangement allows them to take up the mechanical load of the line. But owing to their large weight and brittle nature they are susceptible to vandalism and also they have increased cost of installation and commissioning. But the main problem of porcelain and glass insulators is its performance under polluted environmental condition. Under wet and polluted conditions, the porcelain insulators allow the formation of a conducting layer on the surface which results in setting up of leakage current, dry band arcing and power loss. This problem is further augmented under dc voltages where the stress is unidirectional and the contaminant deposition is higher as compared to ac. Polymeric insulators are a good alternative for porcelain and ceramic insulators for use especially under dc voltages because of their good pollution performance. The property of surface hydrophobicity resists the setting up of leakage currents and hence polymeric insulators help in reducing power loss. They are also light in weight and vandalism resistant and hence easier to install. But being polymeric, they form conductive tracks and erode when exposed to high temperatures which occur at the surface during dry band arcs and when exposed to corona discharges. The surface hydrophobicity is also temporarily lost when exposed to different electrical stresses. Silicone rubber is the most popular among the various choices of polymers for outdoor insulator applications. They have good surface hydrophobicity and tracking performance. But polymers in their pure form cannot be used as insulators because of their poor mechanical strength. Adding inorganic fillers into the polymer matrix not only improves its mechanical properties but also its erosion resistance. Micron sized Alumina Trihydrate (ATH) is used traditionally to improve the tracking and erosion resistance of polymeric insulators. A very high loading (up to 60%) is used. Adding such a high filler loading to the base polymer hampers its flexibility and the material processing. With the advent of nanotechnology, nano fillers have come into vogue. Studies conducted on nano filled polymers showed exciting results. A small amount of nano fillers in the polymer matrix showed significant improvement in the mechanical strength without hampering its flexibility. The electrical properties like tracking and erosion also improved with filler loading. Hence the use of nano filled silicone rubber is a good alternative for use as a high voltage insulator especially under dc voltages. Reports suggest that adding nano fillers into the silicone rubber matrix improves the tracking and erosion resistance and the corona degradation as compared to the unfilled samples under ac voltages. The literature on the dc performance of silicone rubber nano composites is scarce. So the present study aims to evaluate the performance of silicone rubber nano composites for tracking and erosion resistance and corona degradation under dc voltages. The tracking and erosion resistance under dc voltages was measured using the Inclined Plane Tracking and Erosion Resistance set up as per ASTM D2303 which was modified for dc voltage studies. The performance of nano Alumina and nano Silica fillers were evaluated under negative dc and the performance was compared with micron sized Alumina Trihydrate filled samples. The effect of filler loading was also studied. It was seen that the performance of the silicone rubber improved with filler loading. A small loading percentage of nano fillers were enough to give performance similar to silicone rubber filled with micron sized ATH filler. The silicone rubber performed better under negative dc as compared to ac and positive dc. The positive dc tests showed a migration of ions from the electrodes onto the sample surface. The increased surface conductivity resulted in very heavy erosion in the case of positive dc tested samples. The corona aging studies were also conducted on silicone rubber nano composites. Nano silica was used as filler in this case. Different filler loadings were employed to understand the effect of filler loading. The corona was generated using a needle plane electrode and samples were exposed to both positive and negative dc corona. The samples were exposed to corona for different time intervals – 25 and 50 hours to study the effect of exposure time. The hydrophobicity, crack width and surface roughness were measured after the tests. Adding nano fillers into the polymer matrix improved the corona performance. With filler loading, the performance improved. The samples exposed to positive dc corona performed better than those under negative dc corona. The loss of hydrophobicity, surface cracks and the surface roughness was less in the case of positive dc corona tested samples. With exposure time, the performance of silicone rubber became poorer for positive dc corona tested samples. For the negative dc corona tested samples, the performance seemed to improve with exposure time. The tracking and erosion resistance and the corona aging studies conducted showed that the performance of silicone rubber is improved by adding nano fillers into the polymer matrix. A small amount of nano filler loading was enough to perform similar to a heavily loaded micron filled sample. Hence nano fillers can be used as a good functional material to improve the performance of silicone rubber insulators especially under wet and polluted conditions.

The major achievements of this work are based on two categories: (A) introduction of an advanced simulation technique in both time domain and frequency domain, and (B) realistic and reliable models for converters applicable to analysis of alternative transmission systems. The proposed modeling-methodology using a combination of model quadratization and quadratic integration (QMQI) is demonstrated as a more robust, stable, and accurate method than previous modeling methodologies for power system analyses. The quadratic-integration method is free of artificial numerical-oscillations exhibited by trapezoidal integration (which is the most popularly used method in power system analyses). Artificial numerical oscillations can be the direct reason for switching malfunction of switching systems. However, the quadratic-integration method has a natural characteristic to eliminate fictitious oscillations with great simulation accuracy. Also, model quadratization permits nonlinear equations to be solved without simplification or approximation, leading to realistic models of nonlinearities. Therefore, the QMQI method is suitable for simulations of network systems with nonlinear components and switching subsystems. Realistic and reliable converter models by the application of the QMQI method can be used for advanced designs and optimization studies for alternative transmission systems; they can also be used to perform a comprehensive evaluation of the technical performance and economics of alternative transmission systems. For example, the converters can be used for comprehensive methodology for determining the optimal topology, kV-levels, etc. of alternative transmission systems for wind farms, for given distances of wind farms from major power grid substations. In this case, a comprehensive evaluation may help make more-informed decisions for the type of transmission (HVAC, HVDC, and LFAC) for wind farms.

The continuously increasing demand for clean renewable energy has rekindled interest in multi-terminal high voltage direct current (HVDC) grids. Although such grids have several advantages and a great potential, their materialization has been thwarted due to the absence of HVDC breakers. In comparison with traditional alternating current (AC) breakers, they should operate and interrupt fault currents in a time frame of a few milliseconds. The aim of this thesis is focused on the design of ultra-fast electro-mechanical actuator systems suitable for such HVDC breakers.Initially, holistic multi-physics and hybrid models with different levels of complexity and computation time were developed to simulate the entire switch. These models were validated by laboratory experiments. Following a generalized analysis, in depth investigations involving simulations complemented with experiments were carried out on two of the sub-components of the switch: the ultra-fast actuator and the damper. The actuator efficiency, final speed, peak current, and maximum force were explored for different design data.The results show that models with different levels of complexity should be used to model the entire switch based on the magnitude of the impulsive forces. Deformations in the form of bending or elongation may deteriorate the efficiency of the actuator losing as much as 35%. If that cannot be avoided, then the developed first order hybrid model should be used since it can simulate the behavior of the mechanical switch with a very good accuracy. Otherwise, a model comprising of an electric circuit coupled to an electromagnetic FEM model with a simple mechanics model, is sufficient.It has been shown that using a housing made of magnetic material such as Permedyn, can boost the efficiency of an actuator by as much as 80%. In light of further optimizing the ultra-fast actuator, a robust optimization algorithm was developed and parallelized. In total, 20520 FEM models were computed successfully for a total simulation time of 7 weeks. One output from this optimization was that a capacitance of 2 mF, a charging voltage of 1100 V and 40 turns yields the highest efficiency (15%) if the desired velocity is between 10 m/s and 12 m/s.The performed studies on the passive magnetic damper showed that the Halbach arrangement gives a damping force that is two and a half times larger than oppositely oriented axially magnetized magnets. Furthermore, the 2D optimization model showed that a copper thickness of 1.5 mm and an iron tube that is 2 mm thick is the optimum damper configuration. / <p>QC 20150422</p>

An AC system’s voltage unbalance by a fundamental frequency negative sequence system is usually the main cause for the emission of non-characteristic harmonics by current source converters as used in conventional HVDC systems. This emission takes place on both sides of each 12-pulse converter. On the DC side mainly a 2nd harmonic voltage appears driving a 2nd harmonic current. The magnitude of this harmonic current can exceed the magnitudes of the characteristic harmonics even if no low order resonance exists. Further non-characteristic harmonics generated by the converter under such unbalanced supply voltage conditions have frequencies with a frequency distance to the characteristic harmonics of 2 times the fundamental frequency. The main technical drawbacks are the unintended coupling between both AC systems and the risk of thyristor over-stresses by DC current discontinuities at low power transfer levels. On both AC sides the largest 2 non-characteristic current harmonics generated by a 12-pulse HVDC converter under unbalanced supply voltage conditions are a negative sequence system of the fundamental harmonic and a positive sequence system of the 3rd harmonic. Also on the AC sides further harmonics are emitted by the converter with a order number distance of 2 to the orders of the characteristic harmonics. However, in practical AC system operation special attention has to be paid to the 3rd harmonic distortion level, in particular when low order resonance appears between the system impedance and the impedance of the converter station AC filters. In order to avoid the above mentioned problems, large smoothing reactors and sometimes large blocking filters are installed on the DC side and the voltage distortion on the AC sides is reduced by AC filters. However, these filters require an expensive high component rating if they are tuned to the 2nd or 3rd harmonic respectively. The work shows that a modification of the valve firing can reduce the levels of the 2nd and 3rd harmonic without investment into additional primary equipment. Furthermore, this offers the chance to reduce the minimum power transfer level since also the risk of an intermittent DC current can be reduced. A corresponding algorithm and a control strategy are proposed. However, the calculation of an appropriate firing pattern requires a detailed modelling of the processes within the converters, especially the formation of the harmonics and the harmonic transfer between AC and DC sides. The work proposes a component vector model for the calculation of the harmonics. This model assumes that each harmonic consists of a first component representing the ideal conversion process, a 2nd component representing the impact of different commutation angles and in the case of the modified firing a 3rd component considering the impact of the intended non-equidistant firing. The work shows, that the harmonic component vectors resulting from voltage unbalance and from firing modulation can be treated separately and superimposed linearly. The calculation of the harmonic component vectors is performed applying the method of switching functions. For the consideration of the commutation and firing angle differences the modelling of switching functions based on differential impulses is proposed. However, especially an accurate representation of the above mentioned 2nd component vector requires a correct calculation of the commutation angles and their valve-specific differences. The investigations of this work have revealed that the conventional method of calculating the commutation angles – assuming an ideal smoothed DC current - may not produce results of sufficient accuracy. This is especially true in the case of a high ripple of the DC current, e.g. smoothed with a small smoothing reactor. A small smoothing reactor is typical for HVDC back-to-back applications. Therefore a new analytical method for the calculation of the commutation angles has been developed which in particular considers the typical pulse form of the DC current and additionally the impacts of the voltage unbalance and of the proposed modification of the firing on the ripple shape of the DC current. Moreover, as this analytical method requires the instantaneous values of the DC current at the instants of valve firing, a further analytical method for the calculation of these discrete current values has been developed. The equations are valid under the same conditions as the new ones for calculation of the commutation angles, i.e. resistive-inductive AC system fundamental frequency impedances, any degree of DC current smoothing between ideal smoothing and a ripple at the limit for current discontinuities. Symmetrical conditions, supply voltage unbalances and non-equidistant firing as proposed are applied. It is shown that, using this method, also the discrete values of the DC current at the end of the commutation intervals can be determined. In practice one of these discrete current values indicates the minimum value during one period of the fundamental frequency. This offers the chance for a more exact analytical determination of the limit for the appearance of DC current discontinuities. For typical parameters of a back-to-back installation the new methods and the new analytical equations have been compared with simulation results showing excellent correlation for typical voltage unbalances of not more than 1...2% and firing angle differences of not more than 2.5°. This verification is performed for the harmonics, the commutation angles and the discrete values of the DC current at the firing instants as well.

En permettant la transmission de fortes puissances sur de grandes distances, les réseaux en haute tension à courant continu (HTCC) représentent l'avenir du transport de l'énergie électrique. Des équipements tels que les postes sous enveloppe métallique (PSEM) seront indispensables dans ces réseaux pour répartir le flux d'énergie, interrompre ou isoler certaines branches. Leur conception nécessite la prise en compte, pour les parties isolantes, de phénomènes spécifiques liés à l’application de champs électriques continus, comme la dépendance de la résistivité avec le champ et la température, mais également l’accumulation de la charge d'espace qui contribue à augmenter sensiblement les risques de claquage. Dans le composite étudié (résine époxyde chargée d’alumine), ce phénomène commence à se manifester dès que les valeurs de champ excèdent quelques kV/mm, correspondant à l’ordre de grandeur des contraintes envisagées dans les futurs PSEM HTCC.Bien que des techniques existent pour déterminer la répartition de ces charges dans les isolants solides, aucune n’est à ce jour directement applicable aux structures isolantes installées dans les PSEM HTCC.L’objectif de ce travail est ainsi de concevoir et de mettre en place une technique de mesure des charges d’espace et du champ électrique interne qui soit à résolution spatiale, non destructive et adaptée à une géométrie d’isolateur cylindrique, de type support isolant de jeu de barres.En utilisant le dispositif expérimental mis en place, le comportement du composite vis-à-vis de la charge d’espace est par la suite étudié, notamment en fonction de différentes contraintes électrothermiques représentatives du fonctionnement des PSEM. Le but final est d'aider à l'optimisation de la conception de ce type d’isolateur, en se basant sur l’analyse des résultats issus de mesures de charges d’espace. / The trend today is to develop high voltage direct current (HVDC) technology for the future electric network because it offers some advantages for the transmission on long distances. The development of HVDC networks leads to an increasing need of gas insulated substations (GIS). A problem to be dealt with when an insulator is subjected to a continuous electric field is the variation of the resistivity with the electric field and the temperature and the accumulation of space charges that can lead to dielectric breakdown. In alumina-filled epoxy resin, used as insulating material for GIS spacer, the influence of space charge start to come out when the electric fields exceed several kV/mm, corresponding to values envisaged for the future HVDC GIS.Despite that non-destructive methods exist to determine the space charge distribution in solid insulators, none of them are directly applicable to insulation structures installed in the HVDC GIS.So, the main objective of this work is to design and set up a measurement technique to observe the internal electric field and the accumulated charges. The developed method must be non-destructive and adapted for a cylindrical geometry of an insulator used as a busbar insulation support.By using the experimental bench set up, the behavior of the composite material regarding the space charge will be studied, in particular according to different thermoelectric stresses. The final aim is to contribute to the optimization of the design of this type of insulator, based on the results from space charge measurements.