UHF bands because more penetration can be achieved at low frequencies. Consequently, large antennas are required, which limits their use for small airborne applications. This thesis explores various GPR antenna designs for a bi-static system that are at least operational from 225 MHz to 255 MHz and suitable for small airborne applications. The 3D electromagnetic simulation software Ansys high-frequency structure simulator (HFSS) was used to simulate various sizes of strip dipole, triangular bowtie, half elliptical bowtie, and elliptical bowtie antennas. Several physical models were constructed to validate the return loss simulation results. Additionally, simulation data is included for a wire dipole and a helical antenna. The helical antenna proved to be too large for small airborne application, so focus was placed on the dipole and bowtie designs. The performance of the dipole and bowtie antenna models are compared by size, weight, return loss (𝑆11), peak gain, and the transmit-to-receive isolation. Out of the fourteen simulated models, twelve meet the bandwidth requirement with an average weight of 0.23 lbs. It is found that the strip dipole exhibited wider bandwidth characteristics than the triangular, elliptical, and half elliptical bowtie models, while maintaining similar weight and size. The smallest strip dipole model is 50 mm x 528 mm x 1 mm, weighs 0.17 lbs, and is operational from 225 MHz to 283 MHz. Two strip dipole test antennas were fabricated and tested. Test results confirm the simulation predictions.

Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi. / Petroleum Technology Development Fund (PTDF) and National Space Research and Development Agency (NASRDA).

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.

The objectives of this research work are to investigate, design and implement circularly-polarized antennas to be used for handheld satellite mobile communication and wireless sensor networks. Several antennas such as Quadrifilar Spiral Antennas (QSAs), two arm Square Spiral and stripline or coaxially-fed microstrip patch antennas are developed and tested. These antennas are investigated and discussed to operate at L band (1.61-1.6214GHz) and ISM band (2.4835-2.5GHz) A substantial size reduction was achieved compared to conventional designs by introducing special modifications to the antenna geometries. Most of the antennas are designed to produce circularly-polarized broadside-beam except for wireless sensor network application a circularly-polarized conical-beam is considered. The polarization purity and Specific Absorption Rate (SAR) of two dual-band antennas for satellite-mobile handsets next to the human head are investigated and discussed, using a hybrid computational method. A small distance between the head and the handset is chosen to highlight the effects of the relatively high-radiated power proposed from this particular antenna. A Genetic Algorithm in cooperation with an electromagnetic simulator has been introduced to provide fast, accurate and reliable solutions for antenna design structures. Circularly-polarized quadrifilar helical antenna handset and two air-dielectric microstrip antennas were studied. The capabilities of GA are shown as an efficient optimisation tool for selecting globally optimal parameters to be used in simulations with an electromagnetic antenna design code, seeking convergence to designated specifications. The results in terms of the antenna size and radiation performance are addressed, and compared to measurements and previously published data.

Medical devices have made a big step forward in the past decades. One of the most noticeable medical events of the twenties century was the development of long-lasting, wireless electronic implants such as identification tags, pacemakers and neuronal stimulators. These devices were only made possible after the development of small scale radio frequency electronics. Small radio electronic circuits provided a way to operate in both transmission and reception mode allowing an implant to communicate with an external world from inside a living organism. Bidirectional communication is a vital feature that has been increasingly implemented in similar systems to continuously record biological parameters, to remotely configure the implant, or to wirelessly stimulate internal organs. Further miniaturisation of implantable devices to make the operation of the device more comfortable for the patient requires rethinking of the whole radio system concept making it both power efficient and of high performance. Nowadays, high data throughput, large bandwidth, and long term operation requires new radio systems to operate at UHF (ultra-high frequency) bands as this is the most suitable for implantable applications. For instance, the MICS (Medical Implant Communication System) band was introduced for the communication with implantable devices. However, this band could only enable communication at low data rates. This was acceptable for the transmission of telemetry data such as heart beat rate, respiratory and temperature with sub Mbps rates. Novel developments such as neuronal and prosthetic implants require significantly higher data rates more than 10 Mbps that can be achieved with large bandwidth communicating systems operating at higher frequencies in a GHz range. Higher operating frequency would also resolve a strong issue of MICS devices, namely the scale of implants defined by dimensions of antennas used at this band. Operation at 2.4 GHz ISM band was recognized to be the most adequate as it has a moderate absorption in the human body providing a compromise between an antenna/implant scale and a total power efficiency of the communicating system. This thesis addresses a key challenge of implantable radio communicating systems namely an efficient and small scale antenna design which allows a high yield fabrication in a microelectronic fashion. It was demonstrated that a helical antenna design allows the designer to precisely tune the operating frequency, input impedance, and bandwidth by changing the geometry of a self-assembled 3D structure defined by an initial 2D planar layout. Novel stimuli responsive materials were synthesized, and the rolled-up technology was explored for fabrication of 5.5-mm-long helical antenna arrays operating in ISM bands at 5.8 and 2.4 GHz. Characterization and various applications of the fabricated antennas are successfully demonstrated in the thesis.

Master's thesis deals with the design of an antenna system for wireless sound transmission used mainly in professional sound reinforcement. The introductory part deals generally with wireless microphones, frequency bands used and proven antenna types. Next, this work deals with signal distribution that is realized using the antenna splitter. The antenna parts is focused on easy production and real usage, therefore were selected antennas with appropriate properties suitable for small series production. This thesis includes simulation of each device, their real construction design and measurements of built prototypes and final products. All three produced devices – the rack splitter, /4 antenna and Helix antenna are fully working, achieve good parameters and are ready for further manufacturing and easy modifications in case of frequency band change requirement. The conclusion includes an overall assessment of the results achieved.

Medical devices have made a big step forward in the past decades. One of the most noticeable medical events of the twenties century was the development of long-lasting, wireless electronic implants such as identification tags, pacemakers and neuronal stimulators. These devices were only made possible after the development of small scale radio frequency electronics. Small radio electronic circuits provided a way to operate in both transmission and reception mode allowing an implant to communicate with an external world from inside a living organism. Bidirectional communication is a vital feature that has been increasingly implemented in similar systems to continuously record biological parameters, to remotely configure the implant, or to wirelessly stimulate internal organs. Further miniaturisation of implantable devices to make the operation of the device more comfortable for the patient requires rethinking of the whole radio system concept making it both power efficient and of high performance. Nowadays, high data throughput, large bandwidth, and long term operation requires new radio systems to operate at UHF (ultra-high frequency) bands as this is the most suitable for implantable applications. For instance, the MICS (Medical Implant Communication System) band was introduced for the communication with implantable devices. However, this band could only enable communication at low data rates. This was acceptable for the transmission of telemetry data such as heart beat rate, respiratory and temperature with sub Mbps rates. Novel developments such as neuronal and prosthetic implants require significantly higher data rates more than 10 Mbps that can be achieved with large bandwidth communicating systems operating at higher frequencies in a GHz range. Higher operating frequency would also resolve a strong issue of MICS devices, namely the scale of implants defined by dimensions of antennas used at this band. Operation at 2.4 GHz ISM band was recognized to be the most adequate as it has a moderate absorption in the human body providing a compromise between an antenna/implant scale and a total power efficiency of the communicating system. This thesis addresses a key challenge of implantable radio communicating systems namely an efficient and small scale antenna design which allows a high yield fabrication in a microelectronic fashion. It was demonstrated that a helical antenna design allows the designer to precisely tune the operating frequency, input impedance, and bandwidth by changing the geometry of a self-assembled 3D structure defined by an initial 2D planar layout. Novel stimuli responsive materials were synthesized, and the rolled-up technology was explored for fabrication of 5.5-mm-long helical antenna arrays operating in ISM bands at 5.8 and 2.4 GHz. Characterization and various applications of the fabricated antennas are successfully demonstrated in the thesis.