The thermal design constraint of power electronic converters under the specific power loss and heat sink is mainly determined by the maximum permissible junction temperature of the power devices. As the power density and switching frequency increase, transient electro-thermal models become more and more important for the thermal management system design of the power electronic converters. In traction inverters, the junction temperature has huge variation because the fundamental frequency and phase currents vary significantly during the load cycles. Thus, the junction temperature estimation becomes extremely important for the reliability of traction inverters. In this thesis, the transient electro-thermal analysis of a traction inverter considering the inter-dependency of the power losses and junction temperature in an iterative process is implemented. Considering the impact of circuit stray parameters on the switching loss, the temperature dependent power loss model is built based on the datasheet values and the measured switching losses. A state-of-the-art thermal model of the entire inverter including the power modules and the heat sink is developed considering the thermal coupling effects of multiple power devices. By using transient thermal simulation, the linearity of the heat transfer process of the entire traction inverter is verified. The impact of the material thermal properties on the thermal impedance is also presented. In addition, the accuracy of the combination of the thermal subsystem models is verified with simulation. The developed transient electro-thermal model is then used to simulate the junction temperature profiles of the inverter under different operating conditions. Finally, the developed model is experimentally verified. By considering the thermal impedance of the thermal grease layer, the simulation results match with the experimental results very well. The proposed electro-thermal model can provide important information for the thermal management system design, package optimization, long-term reliability analysis, and maximum rating characterization of the traction inverters. / Thesis / Master of Applied Science (MASc)

Due to the limitations of silicon (Si), there is a paradigm shift in research focusing on wide-bandgap-based (WBG) materials. SiC power semiconductors exhibit superiority in terms of switching speed, higher breakdown electric field, and high working temperature, slowly becoming a global solution in harsh medium-voltage (MV) high-power environments. However, to utilize the SiC MOSFET device to achieve those next-generation, high-density, high-efficiency power electronics converters, one must solve a plethora of challenges. For the MV SiC MOSFET device, a high-performance gate-driver (GD) is a key component required to maximize the beneficial SiC MOSFET characteristics. GD units must overcome associated challenges of electro-magnetic interference (EMI) with regards to common-mode (CM) currents and cross-talk, low driving loop inductance required for fast switching, and device short-circuit (SC) protection. Developed GDs (for 1.2 kV, and 10 kV devices) are able to sustain dv/dt higher than 100 V/ns, have less than 5 nH gate loop inductance, and SC protection, turning off the device within 1.5 us. Even with the introduction of SiC MOSFETs, power devices remain the most reliability-critical component in the converter, due to large junction temperature (Tj) fluctuations causing accelerated wear-out. Real-time (online) measurement of the Tj can help improve long-term reliability by enabling active thermal control, monitoring, and prognostics. An online Tj estimation is accomplished by generating integrated intelligence on the GD level. The developed Tj sensor exhibits a maximum error less than 5 degrees Celsius, having excellent repeatability of 1.2 degrees Celsius. Additionally, degradation monitoring and an aging compensation scheme are discussed, in order to maintain the accuracy of the sensor throughout the device's lifetime. Since ultra high-voltage SiC MOSFET devices (20 kV) are impractical, the modular multilevel converter (MMC) emerged as a prospective topology to achieve MV power conversion. If the kernal part of the power-cell (main constitutive part of the MMC converter) is an SiC MOSFET, the design is able to achieve very high-density and high-efficiency. To ensure a successful operation of the power-cell, a systematic design and assessment methodology (DAM) is explored, based on the 10 kV SiC MOSFET power-cell. It simultaneously addresses challenges of high-voltage insulation, high dv/dt and EMI, component and system protections, as well as thermal management. The developed power-cell achieved high-power density of 11.9 kW/l, with measured peak efficiency of n=99.3 %@10 kHz. It successfully operated at Vdc=6 kV, I=84 A, fsw>5 kHz, Tj<150 degrees Celsius and had high switching speeds over 100 V/ns. Lastly, to achieve high-power density and high-efficiency on the MV converter level, challenges of high-voltage insulation, high-bandwidth control, EMI, and thermal management must be solved. Novel switching cycle control (SCC) and integrated capacitor blocked-transistor (ICBT) control methodologies were developed, overcoming the drawbacks of conventional MMC control. These novel types of control enable extreme reduction in passive component size, increase the efficiency, and can operate in dc/dc, dc/ac, mode, potentially opening the modular converter to applications in which it was not previously used. In order to explore the aforementioned benefits, a modular, scalable, 2-cell per arm, prototype MV converter based on the developed power-cell is constructed. The converter successfully operated at Vdc=12 kV, I=28 A, fsw=10 kHz, with high switching speeds, exhibiting high transient immunity in both SCC and ICBT. / Doctor of Philosophy / In medium-voltage applications, such as an electric grid interface in highly populated areas, a ship dc system, a motor drive, renewable energy, etc., land and space can be very limited and expensive. This requires the attributes of high-density, high-efficiency, and reliable distribution by a power electronics converter, whose central piece is the semiconductor device. With the recent breakthrough of SiC devices, these characteristics are obtainable, due to SiC inherent superiority over conventional Si devices. However, to achieve them, several challenges must be overcome and are tackled by this dissertation. Firstly, as a key component required to maximize the beneficial SiC MOSFET characteristics, it is of utmost importance that the high-performance gate-driver be immune to interference issues caused by fast switching and be able to protect the device against a short-circuit, thus increasing the reliability of the system. Secondly, to prevent accelerated degradation of the semiconductor devices due to high-temperature fluctuations, real-time (online) measurement of the Tj is developed on the gate-driver to help improve long-term reliability. Thirdly, to achieve medium-voltage high-power density, high-efficiency modular power conversion, a converter block (power-cell) is developed that simultaneously addresses the challenges of high-voltage insulation, high interference, component and system protections, and thermal management. Lastly, a full-scale medium-voltage modular converter is developed, exploiting the advantages of the fast commutation speed and high switching frequency offered by SiC, meanwhile exhibiting exceptional power density and efficiency.

Dans le cas des installations photovoltaïques, l’onduleur est le premier élément défaillant dont il est difficile d’anticiper la panne, et peu d’études ont été faites sur la fiabilité de ce type de convertisseur. L'objectif de cette thèse est de proposer des outils et méthodes en vue d'étudier le vieillissement des modules de puissance dans ce type d'application en se focalisant sur les phénomènes de dégradation liés à des aspects thermomécaniques. En règle générale, le vieillissement accéléré des modules de puissance est effectué dans des conditions aggravées de courant (Cyclage Actif) ou de température (Cyclage Passif) pour accélérer les processus de vieillissement. Malheureusement, en appliquant ce type de vieillissement accéléré, des mécanismes de défaillances qui ne se produisent pas dans la vraie application peuvent être observés et, inversement, d'autres mécanismes qui se produisent habituellement peuvent ne pas apparaître. La première partie de la thèse se focalise donc sur la mise en place d'une méthode de vieillissement accéléré des composants semi-conducteurs des onduleurs photovoltaïques. Cela est fait en s’appuyant sur l’analyse des profils de mission du courant efficace de sortie des onduleurs et de la température ambiante, extraits des centrales photovoltaïques situées au sud de la France sur plusieurs années. Ces profils sont utilisés pour étudier les dynamiques du courant photovoltaïque, et sont introduites dans des modèles numériques pour estimer les pertes et les variations de la température de jonction des semi-conducteurs utilisés dans les onduleurs, en utilisant l’algorithme de comptage de cycles "Rainflow". Cette méthode est ensuite mise en œuvre dans deux bancs expérimentaux. Dans le premier, les composants sous test sont des modules IGBT. Les composants sont mis en œuvre dans un banc de cyclage utilisant la méthode d'opposition et mettant en œuvre le profil de vieillissement défini précédemment. Un dispositif in-situ de suivi d'indicateurs de vieillissement (impédance thermique et résistance dynamique) est également proposé et évalué. Le deuxième banc est consacré à l'étude de modules de puissance à base de MOSFET SiC. Le vieillissement est effectué dans les mêmes conditions que pour les modules IGBT et de nombreux indicateurs électriques sont monitorés mais, cette fois ci, en extrayant les composants de l'onduleur de cyclage. Les résultats obtenus ont permis de déterminer des indicateurs de vieillissement d’IGBT et de MOSFET SiC utilisés dans un onduleur photovoltaïque / In the case of photovoltaic installations, the DC/AC inverter has the highest failure rate, and the anticipation of its breakdowns is still difficult, while few studies have been done on the reliability of this type of inverter. The aim of this PhD is to propose tools and methods to study the ageing of power modules in this type of application, by focusing on ageing phenomena related to thermo-mechanical aspects. As a general rule, the accelerated ageing of power modules is carried out under aggravated conditions of current (Active Cycling) or temperature (Passive Cycling) in order to accelerate the ageing process. Unfortunately, when applying this type of accelerated ageing tests, some failure mechanisms that do not occur in the real application could be observed, while inversely, other mechanisms that usually occur could not be recreated. The first part of the PhD focuses on the implementation of an accelerated ageing method of the semiconductor devices inside photovoltaic inverters. This is accomplished by analyzing the mission profiles of the inverter’s output current and ambient temperature, extracted over several years from photovoltaic power plants located in the south of France. These profiles are used to study photovoltaic current dynamics, and are introduced into numerical models to estimate losses and junction temperature variations of semiconductors used in inverters, using the cycle counting algorithm “Rainflow”. This method is then performed in two experimental test benches. In the first one, the devices under test are IGBT modules, where the accelerated ageing profile designed is implemented using the opposition method. Moreover, an in-situ setup for monitoring ageing indicators (thermal impedance and dynamic resistance) is also proposed and evaluated. The second bench is devoted to study the ageing of SiC MOSFET power modules. The accelerated ageing test is carried out under the same conditions as for the IGBT modules with more monitored electrical indicators, but this time by disconnecting the semiconductor devices from the inverter. The results obtained allowed to determine several potential ageing indicators of IGBTs and SiC MOSFETs used in a photovoltaic inverter