This work presents the design and construction of a self-deployable, self-stiffening,and retractable (SDSR) space array from carbon fiber reinforced polymers (CFRP’s) and a working prototype is demonstrated. The effort required developing principles for the design of high-strain composite flexural joints and their integration into angled composite panels. Designing LET arrays in angled panels is explored. Analysis of simple composite LET joints is presented for two degrees of freedom. Validation of the composite LET modeling is sought through numerical methods and empirical testing. Testing of several composite LET joint specimens is conducted and the results are reported. Results indicate that (while not as compact as their isotropic material counterparts) composite laminates can successfully use LET joints as surrogate folds.

This thesis addresses a number of challenges designers face when designing deployable origami-based arrays, specifically joint selection, design, and placement within an array. In deployable systems, the selection and arrangement of joint types is key to how the system functions. The kinematics and performance of an array is directly affected by joint performance. This work develops joint metrics which are then used to compare joint performances, constructing a tool designers can use when selecting joints for an origami array. While often a single type of joint is used throughout an array, this work shows how using multiple types of joints within the same array can offer benefits for motion deployment, and array stiffening. Origami arrays are often used for their unique solutions for stowing and deploying large planar shapes. Folds, enabled through joints, within these patterns allow the arrays to fold compactly. However, it can be difficult to fully deploy arrays, particularly array designs with a high number of joints. In addition, it is a challenge to stabilize a fully deployed array from undesired re-folding. This work introduces a strain-energy storing joint that is used to deploy and stiffen foldable origami arrays, the Lenticular Lock (LentLock). Geometry of the LentLock is introduced and the deploying and stiffening performance of the joint is shown. Folds within an origami array create the constraints that link motion between panels, and can be used to create kinematic benefits, such as creating mechanisms with a single degree-of-freedom. While many fold-constraints are required to define motion, this work shows that origami-based system contain many redundant constraints. The removal of redundant joints does not affect the motion of the array nor the observed mobility, but may decrease the likelihood of binding, simplify the overall system and decrease actuation force. This work introduces a visual and iterative approach designers can use to identify redundant constraints in origami patterns, and techniques that can be used to remove the identified redundant constraints. The presented techniques are demonstrated by removing redundant constraints from prototyped origami mechanisms. As a result of this work, designers will be better able to approach and design deployable origami-based mechanisms.

Electronic band structure of various crystal orientations of relaxed and strained bulk, 1D and 2D confined semiconductors are investigated using nonlocal empirical pseudopotential method with spin-orbit interaction. For the bulk semiconductors, local and nonlocal pseudopotential parameters are obtained by fitting transport-relevant quantities, such as band gap, effective masses and deformation potentials, to available experimental data. A cubic-spline interpolation is used to extend local form factors to arbitrary q and the resulting transferable local pseudopotential V(q) with correct work function is used to investigate the 1D and 2D confined systems with supercell method. Quantum confinement, uniaxial and biaxial strain and crystal orientation effects of the band structure are investigated. Regarding the transport relavant quantities, we have found that the largest ballistic electron conductance occurs for compressively-strained large-diameter [001] wires while the smallest transport electron effective mass is found for larger-diameter [110] wires under tensile stress.

<p>In an AP-HTPB propellant microstructure, the local strain rate depends on the AP crystal size and the material, while the local temperature rate depends on the impact velocity, AP crystal size, and the material.  Larger AP crystals lead to higher local strain rates and higher local temperature rates, which means hot spots are more likely to occur in AP-HTPB propellants with more large AP crystals.</p>

TBF 1180 steel was studied under various conditions focusing on the correlation of ductility and amount of retained austenite. Samples were prepared from sheet stock and then strained using limiting dome height tooling (LDH), a standard uniaxial test frame, and a tensile stage for use in an electron microscope. The steel was observed in plane, biaxial, and uniaxial strain to determine its effect on retained austenite transformation and ultimately, ductility. Retained austenite was observed using a scanning electron microscope (SEM) equipped with an electron backscatter detector (EBSD) to distinguish the different phases present. Initial austenite levels were around 5% by volume and was quickly reduced as the sample was strained. The biaxial samples were the slowest to transform, having about 2.5% austenite at .05 effective strain, which allowed the specimen to reach an effective strain of .3 with 1.1% austenite remaining. In contrast, the plane strain samples had the fastest rate of transformation having only 1.2% austenite at .05 effective strain and .7% austenite at a final effective strain of .18. Both forms of uniaxial, (in-situ and ex-situ), were near identical, as expected, and exhibited an austenite transformation curve between that of the plane and biaxial curves. The uniaxial austenite level at .05 strain was 2.1% and was able to reach about .15 strain with a final austenite percentage around 1%. It was concluded that the biaxial strain path had the greatest ductility due in part to its slower austenite transformation rate while plane and uniaxial strain paths were not as ductile with their faster austenite transformation rates.

<p> A research programme is presented to more fully understand the behaviour of Round Hollow Structural Sections subjected to inelastic strain reversals. An attempt is made to establish a preliminary guideline for choosing a reasonable value for the slenderness ratio (D/t) that qualifies the Round HSS for cyclic loading. </p> <p> An experimental programme on nine sections was performed to evaluate the loss in load capacity due to inelastic cyclic loading and to construct the load-deflection hysteresis loops. </p> <p> Three different limiting cyclic deflections were imposed to the smallest D/t section and a comparison was made between the performance of the tube in each case. </p> <p> Prasad's computer program was used to select the strain value at which local buckling will appear and to calculate the half buckle wave-length. The results were compared to the experimental results obtained by the author. </p> <p> A comparison is made between two Round HSS having different diameters and thicknesses but the same D/t ratio. </p> <p> A comparison is made between the behaviour of Round HSS and Square HSS subjected to the same cyclic loading programme. </p> <p> An attempt is made to suggest a reasonable curve relating the number of cycles to failure and the D/t ratio. </p> / Thesis / Master of Engineering (ME)

The effects of repeated loading on a normally consolidated,saturated silty clay, are compared to the effects of sustained loading and standard strength tests on the same material. Attention is given to axial strains and pore water pressures generated under the different loading conditions. / Thesis / Master of Engineering (ME)

The understanding of basic cellular processes has been greatly facilitated through investigation of the behaviour of mutant forms. In a similar way the mechanisms of genetic recombination may be clarified by a study of strains which are known to show inherited differences in recombination behaviour at meiosis. The haploid fungus Neurospora crassa is particularly well suited to such an investigation since recombination frequency heterogeneity has been extensively reported in that organism, and the differences are believed to be, to a large extent, under genetic control. Strains showing recombination frequency heterogeneity over a marked genetic region have been extensively analysed in the present work and the mode of action of the factors controlling recombination frequency has been investigated by combining differing strains in heterokaryons. / Thesis / Doctor of Philosophy (PhD)

The culinary industry is well known for its unforgiving workplace conditions and precarious employment relationships. Low pay, unpredictable schedules, and workplace harassment are commonplace. However, workers in the industry are often dedicated to their craft and passionate about the industry in which they work. This thesis aims to come to a better understanding of the working lives of young kitchen workers in Toronto. Using a narrative approach to research, this thesis draws on the experiences of nine young kitchen workers. Their narratives are analyzed through examining their participation in communities of practice and their experiences of employment strain. It seeks to answer the question of why these individuals enjoy their work but often hate their jobs. / Thesis / Master of Arts (MA) / The culinary industry is well known for its unforgiving workplace conditions and precarious employment relationships. Low pay, unpredictable schedules, and workplace harassment are commonplace. However, workers in the industry are often dedicated to their craft and passionate about the industry in which they work. This thesis aims to come to a better understanding of the working lives of young kitchen workers in Toronto. Using a narrative approach to research, this thesis draws on the experiences of nine young kitchen workers. Their narratives are analyzed through examining their participation in communities of practice and their experiences of employment strain. It seeks to answer the question of why these individuals enjoy their work but often hate their jobs.

<p> Detailed mapping was carried out to provide reliable data concerning the geologic structure which is relevant to the original pebble fabrics. </p> <p> Mathematical determination of an ellipsoidal shape from any two cross-sections and its application to the study of deformed ellipsoidal particles are developed and discussed. </p> <p> Final pebble fabric resulting from special coaxial superpositions of the tectonic strain ellipsoid upon originally ellipsoidal pebbles, is employed to determine the strain ratio and the original pebble orientation and shape. </p> <p> Some general techniques are outlined for different cases to determine the strain ellipsoid and the original shape of deformed pebbles. Weighted vector mean is introduced in the orientation analysis of deformed pebbles. The concept of average axial ratio in the case of unextractable pebbles is examined. </p> <p> Pebble size, pebble ductility ratio, shortening strain, and strain rate are all calculated and discussed. Finally, selective veins developing in the less-deformed pebbles are subjected to detailed orientation and petrofabric analyses. </p> / Thesis / Doctor of Philosophy (PhD)