No description available.

No description available.

京都大学 / 新制・課程博士 / 博士(理学) / 甲第23674号 / 理博第4764号 / 新制||理||1683(附属図書館) / 京都大学大学院理学研究科数学・数理解析専攻 / (主査)准教授 市野 篤史, 教授 池田 保, 教授 雪江 明彦 / 学位規則第4条第1項該当 / Doctor of Science / Kyoto University / DFAM

A supersonic wind tunnel, with a 20" x 20'" test section cross sectional area, was designed and constructed at the Techsburg Wind Tunnel Facility in order to determine the lift and drag on irregularly shaped fragments in supersonic flow. Prior to beginning the wind tunnel design process, a blowdown analysis model was created in order to determine the influence of a number of parameters on tunnel run time and test gas properties throughout the tunnel circuit. The design of the settling chamber, test section, supersonic nozzles, diffuser, and exhaust are presented in this thesis. Diffuser performance has a large influence on wind tunnel efficiency and run time. Therefore, significant efforts should be taken in order to attain the highest possible pressure recovery within the diffuser. The design of wind tunnel components, as well as their stress analysis, was conducted using SolidWorks. The control valve and silencer were sized and selected for the expected tunnel operating conditions. Since the control valve tends to encompass a significant portion of the overall tunnel cost, care must be taken to ensure it has a large enough flow capacity to produce the desired test conditions. Also, attempts must be made to accurately predict the total pressure loss through the silencer, since this loss can have a large impact on the total pressure ratio necessary to produce the design Mach number. Upon completion of the design process, the supersonic wind tunnel was assembled, and shakedown testing was conducted. During shakedown testing it was determined that the wind tunnel was capable of producing Mach 2 flow in the test section. Following shakedown testing, a flow survey was conducted in order to ensure uniform Mach number flow exists throughout the region occupied by the fragments. Based on the flow survey it was determined that within the middle 60% of the test section, the average Mach number was 1.950 and varied by only 0.56% within this region. Two irregularly shaped fragments were tested at Mach 2 flow, over an effective 360° pitch sweep, with wind tunnel runs performed every 10 degrees. Based on the measured force data for both fragments, the lift appeared to follow a sinusoidal curve, with minimum values at 0, 90, and 180° balance pitch angle, and maximum values occurring around 45 and 135° pitch angle. The drag force was observed to follow a gradual curve with minimum values at 0 and 180° balance pitch angle, as expected since the fragment presented area is generally least in this orientation. The maximum drag was found to occur at a balance pitch angle of 90°, once again as expected since the fragment presented area is generally greatest at this angle. It was also observed that the fragment drag tended to be greater for a fragment orientation which places the concave side of the fragment into the direction of the flow. / Master of Science

The purpose of this research is to characterize the response of an airfoil with an oscillatory morphing, Macro-fiber composite (MFC) trailing edge. Correlation of the airfoil lift with the oscillatory input is presented. Modal analysis of the test airfoil and apparatus is used to determine the frequency response function. The effects of static MFC inputs on the FRF are presented and compared to the unactuated airfoil. The transfer function is then used to determine the lift component due to cambering and extract the inertial components from oscillating airfoil. Finally, empirical wind tunnel data is modeled and used to simulate the deflection of airfoil surfaces during dynamic testing conditions. This research serves to combine modal analysis, empirical modeling, and aerodynamic testing of MFC driven, oscillating lift to formulate a model of a dynamic, loaded morphing airfoil. / Master of Science

The evaluation of how Computational Fluid Dynamics (CFD) package may be incorporated into a conceptual design method is performed. The repeatability of the CFD solution as well as the accuracy of the calculated aerodynamic coefficients and pressure distributions was also evaluated on two different wing-body models. The overall run times of three different mesh densities was also evaluated to investigate if the mesh density could be reduced enough so that the computational stage of the CFD cycle may become affordable to use in the conceptual design stage. A farfield method was derived and used in this analysis to calculate the lift and drag coefficients. The CFD solutions were also compared with two methods currently used in conceptual design - the vortex lattice based program Vorview and ACSYNT. The unstructured Euler based CFD package FELISA was used in this study. / Master of Science

A continuous vorticity panel method is developed and utilized to predict the steady aerodynamic loads on lifting surfaces having sharp-edge separation. Triangular and semi-infinite panels with linearly varying vorticity are used. The velocity field generated by an individual element is obtained in closed form. A concentrated core of vorticity is employed to simulate the leading-edge-vortex core and its feeding sheet. An optimization scheme is constructed for finding the vorticity at the nodes of the elements. The method is not restricted by aspect ratios, angles of attack, planforms, or camber. The numerical results are in good agreement with the experimental data for both rectangular and delta wings for incompressible flows. / Ph. D.

Due to a trend towards Ultra High Bypass Ratio engines the corresponding engine/airframe interference is becoming a key aspect in aircraft design. The present economic situation increases the pressure on commercial aviation companies to reduce the Direct Operating Cost, and the environmental situation requires a new generation of aircraft with a lower environmental impact. Therefore detailed aerodynamic investigations are required to evaluate the real benefits of new technologies. The presented research activity is part of a long-term project with the main objective of generating a reliable and accurate tool to predict the performance of an aircraft over the whole flight domain. In particular the aim of this research was to perform advanced CFD in order to establish a tool able to evaluate engine installation effects for different configurations and attitudes. The developed tool can be provided with correlations of the Net Propulsive Force (NPF), the force exerted by the power-plant to the aircraft, as a function of position. This can be done in principle at cruise, hold, climb, descent, take-off and landing, to model the different integration effects at different phases. Due to the complexity of the problem it was only possible at an initial stage to determine these correlations at cruise condition. Two parametric test cases were evaluated, showing that the engine horizontal positioning can influence the mission fuel burn by up to 6.4%. According to the extensive literature review that has been done, this study can be regarded as the first open literature engine position-NPF parametric study using CFD. Even though no correlations were extracted for other conditions; a deployed high-lift wing configuration was also studied in detail, defining the main aerodynamics effects of the engine integration at high angle of attack. A topological study of the high-lift installation vortices is presented in this work and it can be considered the first in the open literature. It should be pointed out that extensive research is currently underway to correctly evaluate the high-lift aerodynamic using CFD. The Propulsive System Integration (PSI) in high-lift conditions is adding flow features to an already demanding problem, making it a real challenge for the numerical methods. Nevertheless the additional effects of a nacelle chine on the maximum lift were also evaluated. The main outcomes of this PhD research were: a coupled performance modelling tool able to handle the effects of engine-airframe integration as a function of geometry and attitude, and a topological study of the high-lift installation vortices. During the course of the work, this research was successfully suggested as an extra activity for the European NEWAC project (New Aero Engine Core Concepts), and resulted in a new deliverable for that project.

Due to a trend towards Ultra High Bypass Ratio engines the corresponding engine/airframe interference is becoming a key aspect in aircraft design. The present economic situation increases the pressure on commercial aviation companies to reduce the Direct Operating Cost, and the environmental situation requires a new generation of aircraft with a lower environmental impact. Therefore detailed aerodynamic investigations are required to evaluate the real benefits of new technologies. The presented research activity is part of a long-term project with the main objective of generating a reliable and accurate tool to predict the performance of an aircraft over the whole flight domain. In particular the aim of this research was to perform advanced CFD in order to establish a tool able to evaluate engine installation effects for different configurations and attitudes. The developed tool can be provided with correlations of the Net Propulsive Force (NPF), the force exerted by the power-plant to the aircraft, as a function of position. This can be done in principle at cruise, hold, climb, descent, take-off and landing, to model the different integration effects at different phases. Due to the complexity of the problem it was only possible at an initial stage to determine these correlations at cruise condition. Two parametric test cases were evaluated, showing that the engine horizontal positioning can influence the mission fuel burn by up to 6.4%. According to the extensive literature review that has been done, this study can be regarded as the first open literature engine position-NPF parametric study using CFD. Even though no correlations were extracted for other conditions; a deployed high-lift wing configuration was also studied in detail, defining the main aerodynamics effects of the engine integration at high angle of attack. A topological study of the high-lift installation vortices is presented in this work and it can be considered the first in the open literature. It should be pointed out that extensive research is currently underway to correctly evaluate the high-lift aerodynamic using CFD. The Propulsive System Integration (PSI) in high-lift conditions is adding flow features to an already demanding problem, making it a real challenge for the numerical methods. Nevertheless the additional effects of a nacelle chine on the maximum lift were also evaluated. The main outcomes of this PhD research were: a coupled performance modelling tool able to handle the effects of engine-airframe integration as a function of geometry and attitude, and a topological study of the high-lift installation vortices. During the course of the work, this research was successfully suggested as an extra activity for the European NEWAC project (New Aero Engine Core Concepts), and resulted in a new deliverable for that project.

The aim of the diploma thesis was the conceptual design of a service lift driven by the rigid chain. The introduction part focuses on a general description of lifts and existing issues. The following chapters contain the created lift design, construction of important design elements and functional calculations. In the conclusion, evaluation compared with hydraulic lifts and evaluation of speed of the lift, starting and braking to exact stop are performed.