The target of this dissertation is based on the specified shape of plastic part to develop search technology of plastic injection molds, to the technological design process and construction of injection molds, including the necessary calculations. The project includes a search and a practical sections. Based on information from a search section a suitable material was chosen, which became the basis for practical section. The practical section with basic technology calculation is complemented by filling simulation analysis and stress analysis of critical elements. A part of this dissertation is the set of the drawings.

The theory of plastic injection molding technology together with procedure of designing injection molds is elaborated in this master thesis. Also, the technology of production is designed, derived from assigned component „cover“ analysis affirmed by necessary calculations. On the bases of these calculations, injection machine fitting requirements is chosen. Then injection mold is designed for the assigned component. Simulation of injection is performed for this mold using Autodesk Inventor 2011 and its module Moldflow and then results are thoroughly analyzed. Economical evaluation for this component is then executed towards the end of the thesis.

The aim of the thesis is to propose the innovation of thermomould machine so that the complicated substitution of the distribution plate is eliminated. The diploma thesis documents the application of automatization in a small food processing company and contains a description of problems connected to the use of automatization in small and middle enterprises (SME). The thesis describes the solution of the universality of the distribution plate and its control by means of an operating systém that is implemented with a single-purpose board that is equipped with microelectronic components. The thesis ends with an economic analysis of the suggested solution.

Master’s thesis deals with selection of a proper technology for manufacturing of chosen plastic part. The beginning of thesis contains part survey. Plastic injection was chosen as the most suitable manufacturing technology. Required theoretical knowledge for plastic injection mould designing were extracted in the recherche. Individual chapters deals with plastics, their manufacturing and plastic injection technology with all required knowledge about this technology, machines and moulds. Designing chapter contains every required calculation for mould design and all individual sections of mould design and injection machine selection. Injection simulations and their evaluations are part of this thesis aswell. Assembly and forms drawings as well as other documents used during thesis processing are included in the attachments.

This thesis describes a design of an injection mould for plastic part "Sleeve", that is intended for guiding of sliding door hardware. The part is manufactured from PE-HD, production quantity is 3 000 000 pcs annually. Based on calculations and review of specialized literature the design utilizes hot runners of MH system by Ewicon. The tool is assembled from normalized components by Hasco and an injection press BOY22D was suggested for parts production. Total costs for production of 1 part are 0,26 CZK.

This thesis deals with the production of a plastic body of the aperture by the method of injection moulding. The work includes a design of the injection mould for the given component. First, an appropriate material for the moulded piece was chosen and then the necessary calculations for the injection mould were made. A quadruplex injection mould with a heated inlet nozzle and pullout cores was designed based on these calculations. Modular components were chosen when designing the injection mould. The next part of the thesis contains the selection of the injection moulding machine for the given mould. The conclusion contains a technical-economical evaluation including the cost estimating for the injection mould and cost estimating for one moulded piece.

This thesis contains of theoretical part which deals with injection molding, properties of some polymer materials are included also. Design of plastic injection mold for cover of electronic device is presented in practical part. Manufacturing parameters and injection machine selection are specified with mold structure consideration. Production costs and the final price of the plastic part are calculated in economical evaluation.

Diploma thesis which is developed for the master’s degree program (M2I – K Mechanical engineering) presents a proposal solution for production technology plastic car headlins parts from polymer material PBT GF30. Literature review summarizes the findings of thermoplastic injection technology and the structural design possibility of injection molds. The paper examined two variants of the running system, which are suitable for production of injection molding components. Finaly, after technical - economic assessment, we came to the conclusion that the better option is to use the hot runner system. In the practical part is the specified product modeled by the help of 3D software and the injection mold was designed. The design was implemented by CATIA V5 R20. For the design and manufacture of injection mold were used normality from MEUSBURGER. For the chosen alternative technology of production were made calculations and was selected injection molding machine Electron 75 – 300 from FERROMATIC.

The aim of this diploma work was a proposal to make the process of machining of injection mould more efficient. The work described the initial state of machining of a moulding injection part from the technological point of splinter machining, including the description of each production areas, the tool used in the process and the machines. The main part of the diploma work was focused on consideration of a possible way leading to the increase in the efficiency of the production process of machining of an injection mould part that included the transfer of the initial way of machining of a moulding injection part to CNC lathe Gildemeister CTX beta 500. Furthermore the work described the tool that had been used including the description of proposed control programs for machining of an injection mould part. The essential part of the work was a techno-economical assessment of the proposed variant of solution, which included analysis of the production costs and the time indexes that were achieved during the production.

This project has been developed within the master study of Engineering Technology and Industrial Management a design of manufacturing technology for plastic cogwheel is introduced. The cogwheel will be produced by plastic injection moulding. POM material with a trade name Delrin 100 NC010 from DuPont Company will be used. An injection mould is a tool for producing a plastic cogwheel using injection moulding technology. Production will take place on the machine Allrounder 420 C Golden Edition 1000-290 from Arburg German Company headquartered in Loßburg, where the seat of parent company is situated.