An analytical and numerical investigation is conducted for the lateral torsional buckling analysis of wooden beam with a mid-span lateral brace subjected to symmetrically distributed loading. Two models are developed; one for the case of a rigid brace and another one for the case of a flexible brace. The analytical solutions are based on the principle of stationary potential energy and a Fourier expansion of the buckling displacement fields and bending moments. The validity of both models are verified against 3D finite element analyses in ABAQUS. Where applicable, verifications were also conducted against available solutions from previous studies. Parametric studies were conducted to investigate the effect of geometric and material parameters on the critical moments. The results indicate the presence of two separate groups of potential buckling modes, symmetric and anti-symmetric, with fundamentally different behavioural characteristics. The governing buckling mode is shown to depend on the bracing height, load height and lateral brace stiffness. The study shows that beyond a certain threshold bracing height, the critical moment is governed by the antisymmetric mode of buckling. Also, above a certain optimum bracing stiffness, no increase is observed in the critical moments. The models developed are used to construct a comprehensive database of parametric investigations which are then employed for developing simplified equations for determining the threshold heights, associated critical moments, and optimum stiffness.

The research summarized in this thesis is comprised of an experimental analysis of the mechanical behavior of a wood composite I-joist with different bracing configurations exposed dynamic walking loads. Three 16 in. deep GPI® 65 I-joists were simply supported and laid parallel to each other, while the bracing was attached to the top flange. Five different brace stiffnesses were used: zero stiffness (control), 1.2 lb/in., 8.5 lb/in., 14.0 lb/in. and infinitely stiff. Two different brace configurations were used: one-quarter of the span length (60 in.) and one third the span length (80 in.). The dynamic walking loads consisted of human test subjects attached to a safety platform walking across the I-joist at a designated pace. Experimental results for this research consisted of the I-joist's lateral accelerations, lateral displacements and twist. An Analysis of Covariance (ANCOVA) was used for the statistical analysis of the results and was performed for each measurement. The statistical analysis determined the effects of different bracing configurations, stiffnesses, measurement locations as well as test subjects' weight and occupation. Test results and observed trends are provided for all test configurations. Lateral displacement and twist experienced the same trend throughout the experiment: as brace stiffness increased, lateral displacement and twist decreased. This correlated with basic beam theory and bracing fundamentals. It should be noted that as the stiffness increased, the effect on lateral displacement and twist response decreased. However, the trend for lateral displacement and twist was not observed for the lateral accelerations. The 1.2 lb/in. brace stiffness had much larger lateral accelerations for the 60 in. brace configuration throughout the span and were also larger at the bracing point for the 80 in. brace configuration. This could have been due to the energy applied from the springs or a natural frequency of the I-joist system could have been reached during testing. However, the other four brace stiffnesses followed the same trend as the lateral displacements and twist. In addition, this research demonstrates a method for the measurement of lateral buckling due to worker loads. The mitigation of lateral buckling can use appropriate bracing systems. The measurements of the change in lateral buckling behavior can be used to develop safety devices and ultimately ensure the protection of construction workers. / Master of Science

Light-frame shearwall assemblies have been successfully used to resist gravity and lateral loads, such as earthquake and wind, for many decades. However, there is a need for maintaining the structural integrity of such buildings even when large openings in walls are introduced. Wood portal frame systems have been identified as a potential alternative to meet some aspects of this construction demand. The overarching goal of the research is to develop wood portal frame bracing systems, which can be used as an alternative or in combination with light-frame wood shearwalls. This is done through investigating the behavior of wood portal frames using the MIDPLY shearwall framing technique. A total of 21 MIDPLY corner joint tests were conducted with varying bracing details. Also, a finite element model was developed and compared with test results from the current study as well as studies by others. It was concluded from the corner joint tests that the maximum moment resistance increased with the addition of metal straps or exterior sheathings. The test results also showed a significant increase in the moment capacity and rotational stiffness by replacing the Spruce-Pine Fir (SPF), header with the Laminated Veneer Lumber (LVL) header. The addition of the FRP to the standard wall configuration also resulted in a significant increase in the moment capacity. However, no significant effect was observed on the stiffness properties of the corner joint. The FE model was capable of predicting the behavior of the corner joints and the full-scale portal frames with realistic end-conditions. The model closely predicted the ultimate lateral capacity for all the configurations but more uncertainty was found in predicting the initial stiffness.The FE model used to estimate the behavior of the full-scale portal frames constructed using the MIDPLY framing techniques showed a significant increase in the lateral load carrying capacity when compared with the traditional portal frame. It was also predicted using the full-scale FE model that the lateral load carrying capacity of the MIDPLY portal frame would increase with the addition of the metal straps on exterior faces. A parametric study showed that using a Laminated Strand Lumber (LSL) header increased the lateral load carrying capacity and the initial stiffness of the frames relative to the SPF header. The study also showed that there was an increase in the capacity if high strength metal straps were used. Doubling of the nail spacing at header and braced wall segment had a considerable effect on the lateral capacity of portal frame. Also, the initial stiffness was reduced for all the configurations with the doubling of the nail spacing at the header and braced wall segment in comparison with the reference frame.

Light-frame shearwall assemblies have been successfully used to resist gravity and lateral loads, such as earthquake and wind, for many decades. However, there is a need for maintaining the structural integrity of such buildings even when large openings in walls are introduced. Wood portal frame systems have been identified as a potential alternative to meet some aspects of this construction demand. The overarching goal of the research is to develop wood portal frame bracing systems, which can be used as an alternative or in combination with light-frame wood shearwalls. This is done through investigating the behavior of wood portal frames using the MIDPLY shearwall framing technique. A total of 21 MIDPLY corner joint tests were conducted with varying bracing details. Also, a finite element model was developed and compared with test results from the current study as well as studies by others. It was concluded from the corner joint tests that the maximum moment resistance increased with the addition of metal straps or exterior sheathings. The test results also showed a significant increase in the moment capacity and rotational stiffness by replacing the Spruce-Pine Fir (SPF), header with the Laminated Veneer Lumber (LVL) header. The addition of the FRP to the standard wall configuration also resulted in a significant increase in the moment capacity. However, no significant effect was observed on the stiffness properties of the corner joint. The FE model was capable of predicting the behavior of the corner joints and the full-scale portal frames with realistic end-conditions. The model closely predicted the ultimate lateral capacity for all the configurations but more uncertainty was found in predicting the initial stiffness.The FE model used to estimate the behavior of the full-scale portal frames constructed using the MIDPLY framing techniques showed a significant increase in the lateral load carrying capacity when compared with the traditional portal frame. It was also predicted using the full-scale FE model that the lateral load carrying capacity of the MIDPLY portal frame would increase with the addition of the metal straps on exterior faces. A parametric study showed that using a Laminated Strand Lumber (LSL) header increased the lateral load carrying capacity and the initial stiffness of the frames relative to the SPF header. The study also showed that there was an increase in the capacity if high strength metal straps were used. Doubling of the nail spacing at header and braced wall segment had a considerable effect on the lateral capacity of portal frame. Also, the initial stiffness was reduced for all the configurations with the doubling of the nail spacing at the header and braced wall segment in comparison with the reference frame.

Light-frame shearwall assemblies have been successfully used to resist gravity and lateral loads, such as earthquake and wind, for many decades. However, there is a need for maintaining the structural integrity of such buildings even when large openings in walls are introduced. Wood portal frame systems have been identified as a potential alternative to meet some aspects of this construction demand. The overarching goal of the research is to develop wood portal frame bracing systems, which can be used as an alternative or in combination with light-frame wood shearwalls. This is done through investigating the behavior of wood portal frames using the MIDPLY shearwall framing technique. A total of 21 MIDPLY corner joint tests were conducted with varying bracing details. Also, a finite element model was developed and compared with test results from the current study as well as studies by others. It was concluded from the corner joint tests that the maximum moment resistance increased with the addition of metal straps or exterior sheathings. The test results also showed a significant increase in the moment capacity and rotational stiffness by replacing the Spruce-Pine Fir (SPF), header with the Laminated Veneer Lumber (LVL) header. The addition of the FRP to the standard wall configuration also resulted in a significant increase in the moment capacity. However, no significant effect was observed on the stiffness properties of the corner joint. The FE model was capable of predicting the behavior of the corner joints and the full-scale portal frames with realistic end-conditions. The model closely predicted the ultimate lateral capacity for all the configurations but more uncertainty was found in predicting the initial stiffness.The FE model used to estimate the behavior of the full-scale portal frames constructed using the MIDPLY framing techniques showed a significant increase in the lateral load carrying capacity when compared with the traditional portal frame. It was also predicted using the full-scale FE model that the lateral load carrying capacity of the MIDPLY portal frame would increase with the addition of the metal straps on exterior faces. A parametric study showed that using a Laminated Strand Lumber (LSL) header increased the lateral load carrying capacity and the initial stiffness of the frames relative to the SPF header. The study also showed that there was an increase in the capacity if high strength metal straps were used. Doubling of the nail spacing at header and braced wall segment had a considerable effect on the lateral capacity of portal frame. Also, the initial stiffness was reduced for all the configurations with the doubling of the nail spacing at the header and braced wall segment in comparison with the reference frame.

Z-sections are widely used as secondary members in metal building roof systems. Lateral restraints are required to maintain the stability of a Z-section roof system and provide resistance to the lateral forces generated by the slope of the roof and the effects due to the rotation of the principal axes of the Z-section relative to the plane of the roof sheathing. The behavior of Z-sections in roof systems is complex as they act in conjunction with the roof sheathing as a system and as a light gage cold formed member, is subject to local cross section deformations. The goal of this research program was to provide a means of predicting lateral restraint forces in Z-section supported roof systems. The research program began with laboratory tests to measure lateral restraint forces in single and multiple span sloped roof systems. A description of the test apparatus and procedure as well as the results of the 40 tests performed is provided in Appendix II. To better understand the need for lateral restraints and to provide a means of testing different variables of the roof system, two types of finite element models were developed and are discussed in detail in appended Paper I. The first finite element model is simplified model that uses frame stiffness elements to represent the purlin and sheathing. This model has been used extensively by previous researchers and modifications were made to improve correlation with test results. The second model is more rigorous and uses shell finite elements to represent the Z-section and sheathing. The shell finite element model was used to develop a calculation procedure referred to as the Component Stiffness Method for predicting the lateral restraint forces in Z-section roof systems. The method uses flexural and torsional mechanics to describe the behavior of the Z-section subject to uniform gravity loads. The forces generated by the system of Z-sections are resisted by the "components" of the system: the lateral restraints, the sheathing and Z-section-to-rafter connection. The mechanics of purlin behavior providing the basis for this method are discussed in appended Paper II. The development of the method and the application of the method to supports restraints and interior restraints are provided in appended papers III, IV and V. / Ph. D.

This thesis deals with the subject of lateral bracing between the bottom flanges of I-girder composite bridges. The focus is on the impact of adding lateral bracing on existing bridges, as well as on new bridges. Experience and knowledge from bridge projects around the world are investigated and implemented in the evaluation of the research subject. Many existing bridges are in need of being strengthened or replaced, due to the increased traffic volume and heavier traffic loads. Different approaches can be used to prolong the lifetime of existing bridges. The approach is different depending on the cause, but for increasing the lifetime regarding fatigue some of the most suitable options are described in this thesis. A proposed concept is presented, in this thesis, along with some research questions to be answered. The use of lateral bracings in composite bridges varies between different parts of the world. In one country it can be a requirement/common praxis for long span composite bridges with two I-girders, in other countries there are no requirements of using them. Some parts of these regulations and requirements can be traced back to the tradition in both manufacturing and construction of this type of bridges. This thesis investigates how lateral bracing is used around the world to distribute eccentric loads between primary longitudinal structural members, provide resistance to lateral loads, and to permit an existing two-girder structural system to be retrofitted to behave similarly to an often more expensive closed steel box girder. Furthermore, several case studies have been conducted to investigate the impact on the structural behavior of composite bridges where a lateral bracing is implemented in the structure. The results from these case studies are presented in the thesis and show the advantages of the quasi-box section for which the lateral bracing is closing the composite cross section. By making the I-girder composite cross section acting more like a box-section, the distribution of eccentric loads between the girders is improved. The impact on longitudinal stresses from traffic loads and the additional effects on internal sectional parts are also evaluated and discussed. Furthermore, proposals of the connection design for lateral bracings in existing bridges are suggested. Finally, conclusions from the results are stated.

The topic of the thesis is a project of roof of a multifunctional sport object with a ground-plan covering area 35x48m, and maximum height of 16m. This construction is projected for Brno and its surroundings. The project of roofing is evolved in two different variants. First one is formed by double-jointed arched latticed truss. Supporting components such as purlins, lateral and longitudal bracings, frontal column and anchorage are designed and assessed in static calculation. At the end of the thesis, comparison of both variants is elaborated. Design documentation, which consists of dispositional drawing, drawing of truss for manufacturing, drawing of indicative details and plan of anchorage, is a part of the thesis.

Diploma thesis is developed the design and static assessment supporting steel structure Exhibition Hall of the overall ground dimensions 47x66m with a maximum height of 15.4 meters. Layout is designed in accordance with architectural requirements. The design is considered for Brno´s area. The proposal of roof system is designed in two versions whose dimensions are identical. The first option consists of a two-aisle hall object, parabolic truss girder, pin supported on fixed columns. The second variant also two-aisle building with truss frame structure assessed in static calculation. At the end of the thesis, comparison of both variants is elaborated. Design documentation, which consist layout drawing, drawing of truss for manufacturing, drawing indicative details and plan of anchorage, is a part od thesis