The lateral resistance of pile foundations has typically been based on the resistance of circular pipe piles. In addition, most instrumented lateral load tests and cases history have involved circular piles. However, piles used in engineering practice may also be non-circular cross-section piles such as square and H piles. Some researchers have theorized that the lateral resistance of square piles will be higher than that of circular piles (Reese and Van Impe, 2001; Briaud et al, 1983; Smith, 1987) for various reasons, but there is not test data to support this claims. To provide basic comparative performance data, lateral load tests were performed on piles with circular, square and H sections. To facilitate comparisons, all the tests piles were approximately 12 inches in width or diameter and were made of steel. The square and circular pipe sections had comparable moments of inertia; however, the H pile was loaded about the weak axis, as is often the case of piles supporting integral abutments, and had a much lower moment of inertia. The granular fill around the pile was compacted to approximately 95% of the standard Proctor maximum density and would be typical of fill for a bridge abutment. Lateral load was applied with a free-head condition at a height of 1 ft above the ground surface. To define the load-deflection response, load was applied incrementally to produce deflection increments of about 0.25 inches up to a maximum deflection of about 3 inches. Although the square and pipe pile sections had nearly the same moment of inertia, the square pile provided lateral resistance that was 20 to 30% higher for a given deflection. The lateral resistance of the H pile was smaller than the other two pile shapes but higher than what it is expected based on the moment of inertia. Back analysis with the computer program LPILE indicates that the pile shape was influencing the lateral resistance. Increasing the effective width to account for the shape effect as suggested by Reese and Van Impe (2001) was insufficient to account for the increased resistance. To provide agreement with the measured response, p-multipliers of 1.2 and 1.35 were required for the square pile and H piles, respectively. The analyses suggest that the increased resistance for the square and H pile sections was a result of increases in both the side shear and normal stress components of resistance. Using the back-calculated p-multipliers provided very good agreement between the measured and computed load-deflection curves and the bending moment versus depth curves.

Motivated by the structure of the normal surface stress of the extended Hertzian approach [1] given due to terms of the form r^2n*(a^2-r^2)^(1/2) (n=0, 2, 4, 6…) it seems attractive to evaluate the complete elastic field also for shear loadings of this form. The reason for this lays in the demand for analytical tools for the description of mixed loading conditions as they appear for example in scratch experiments. [1] N. Schwarzer, "Elastic Surface Deformation due to Indenters with Arbitrary symmetry of revolution", J. Phys. D: Appl. Phys., 37 (2004) 2761-2772

<p> A moment resisting frame is one of the most commonly used lateral load resisting system in modem structures because it is suitable for low and medium rise buildings and industrial structures. It can be designed to behave in a ductile manner under seismic loads. </p> <p> Masonry infills have traditionally been used in buildings as partitions and for architectural or aesthetic reasons. They are normally considered as non-structural elements, and their effect on the structural system has been ignored in the design. However, even though they are considered non-structural elements, there is mounting evidence that they interact with the frame when the structures are subjected to lateral loads Infill walls have been identified as a contributing factor to catastrophic structural failures during earthquakes. Frame-infill interaction can induce brittle shear failures of reinforced concrete columns by creating a short column. Furthermore, infills can over-strengthen the upper stories of a structure and when they fail a soft first storey is created, which is highly undesirable from the earthquake resistance standpoint. </p> <p> There is a need for an efficient and accurate computational model to simulate the nonlinear hysteretic force-deformation behaviour of masonry infills, which is also suitable for implementation in time-history analysis of large structures. The aim is to develop a simplified advanced and cost-effective model for nonlinear time history analysis and seismic design of masonry infill frame structures. </p> <p> The objective of this research was to develop a practical and economical technique applicable for global analysis of general three-dimensional reinforced concrete infilled frames under lateral loads. Novel finite element model for the infill and the surrounding frame was developed using a special finite element configuration to represent the masonry panel. Some prescribed failure planes in different directions were defined depending on the common failure mode of masonry panels. Moreover, some of contact elements were used on the failure planes to connect among the panel elements, and between the panel elements and the boundary reinforced concrete frame. Different material models were used to represent the behaviour of concrete, reinforcing steel, mortar joints and inclined saw-tooth cracks in the infill panel. Different material models were used to describe the behaviour through and perpendicular to the prescribed failure planes. The proposed model and the used material models were described in details in the first part of this research. </p> <p> The proposed finite element model was verified against experimental and analytical results previously published by others. Different frames configurations, reinforcing details, boundary conditions and material properties were consider in that section to verify the capability of the proposed model to simulate the behaviour of different frames. The overall behaviour "Load-deflection relationship", failure point and failure mode were compared with the experimental and analytical results. Satisfactory agreement with the previously published results was obtained. </p> <p> The study investigates the capability of the proposed model to simulate the behaviour of infilled frames subjected to cyclic loads. Hysteretic loops obtained by using the new model were verified against experimental and analytical results and good correlation were obtained. The failure modes and crack patterns were compared with the experimental results and good agreements were obtained. The proposed model failed to capture some shear cracks in the RC frames as per the experimental results. </p> / Thesis / Doctor of Philosophy (PhD)

A series of static lateral load tests were conducted on a group of fifteen piles arranged in a 3x5 pattern. The piles were placed at a center-to-center spacing of 3.92 pile diameters. A single isolated pile was also tested for comparison to the group response. The subsurface profile consisted of cohesive layers of soft to medium consistency underlain by interbedded layers of sands and fine-grained soils. The piles were instrumented to measure pile-head deflection, rotation, and load, as well as strain versus pile depth.