Electrochemical copolymerizations of thiophene (Th) and 3,4-ethylenedioxythiophene (EDOT) was performed in this study. Incorporation of Th with EDOT units have accelerated deposition rate in relative to the simple polymerization behavior of EDOT. The electrochemical properties of poly(thiophene-co-3,4-ethylenedioxythiophene) (PTh-EDOT) are different from the homopolymers of polythiophene (PTh) and poly(3,4-ethylenedioxythiophene) (PEDOT). PTh-EDOT were then served as cathode materials of lithium-ion (Li-ion) batteries to test their capability to transfer lithium ion in 1.0 M LiPF6/ethylene carbonate/dimethyl carbonate solution. PTh-EDOT copolymer prepared from the monomer ratio of 1/1 (Th/EDOT) shows better stability than PEDOT and PTh homopolymers, polymer property enhancement by copolymerization is thus demonstrated. A composite electrode material PEDOT/LiCoO2 was prepared from the electrochemical polymerization of EDOT on LiCoO2 electrode was primarily prepared to inspect the influence of PEDOT on the electrochemical features of LiCoO2. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) show the successful deposition of PEDOT over LiCoO2 particles. Compared to the simple LiCoO2 electrode, PEDOT/LiCoO2 composite cathode shows enhanced properties including rate capability and cycle stability for potential Li-ion battery application. Nevertheless, differential scanning calorimetry (DSC) scans on the fully charged cathodes imply that PEDOT may reduce the thermal stability of LiCoO2. Two carbon materials, vapor grown carbon fibers (VGCF) and nano-scaled Ketjen black EC (KB), were implemented into LiCoO2 electrode. The influence of different carbon additive and their content on the performance of LiCoO2 such as rate capability and cycle ability has been evaluated. KB shows more positive effects than VGCF even in the case of a low 1 wt% content. Furthermore, incorporation of PEDOT was made by electrochemical deposition of EDOT on the preformed LiCoO2-VGCF and LiCoO2-KB composite electrodes. The influence of the carbon additives and the conductive PEDOT polymer on LiCoO2 was then investigated. Compared to the electrodes without PEDOT coating, PEDOT-incorporated composite electrodes show larger capacity, better transfer rate of lithium ions in electrolytes, and enhanced cycle ability. The electrochemical deposition of PEDOT on the LiCoO2/nano-carbon cathodes provides a new approach to implement the conducting polymers in Li-ion batteries.

Au cours de ce travail de thèse, nous avons mis au point un procédé d'élaboration reproductible de films minces de LiCoO2 par pulvérisation cathodique radio fréquence. L'étude paramétrique nous a permis de déterminer les conditions de dépôt optimales ainsi que les conditions de traitement thermique post-dépôt les plus adaptées afin d'aboutir aux meilleures propriétés électrochimiques pour ces électrodes. Une fois optimisés, les films minces ont été étudiés en électrolyte liquide et nous avons notamment évalué l'influence sur les performances électrochimiques de l'épaisseur du film, de la densité de courant employée, ainsi que des bornes de potentiel utilisées. Nous avons mis en évidence un excellent comportement des films sur une large gamme d'épaisseurs et régimes. La capacité obtenue pour un film de 3,6 µm à 10 µA.cm-2 est de 240 µAh.cm-2. Une étude par microspectrométrie Raman permet de montrer que les changements structuraux induits par les processus électrochimiques sont mineurs et limités à une élongation réversible des liaisons Co-O dans l'axe d'empilement. L'intégration d'un film de 450 nm d'épaisseur dans un microaccumulateur tout solide (LiCoO2/LiPON/Li) a confirmé les excellents résultats obtenus en électrolyte liquide avec une capacité de 25 µAh.cm-2. Là encore, le comportement du film reste inchangé pour des densités de courant élevées allant jusqu'à 800 µA.cm-2. Le cyclage du microaccumulateur à 10 µA.cm-2 a été maintenu pendant plus de 800 cycles sans perte notable de capacité. Pour la première fois on démontre que des films minces de LiCoO2 élaborés par pulvérisation cathodique et recuits à 500°C peuvent être utilisés dans un microaccumulateur au lithium tout solide avec des performances proches de la théorie

This diploma thesis deals with materials used by production ofcathodes of Lithium-ion batteries. Primary this thesis deals with LiCoO2material and its subsidizing of alkali metals. The first part deals with the charakteristic of Lithium-ion batteries, used materials, possibilities of doping and charging. The practical part concentrates on production of active substance of cathode and doping this substance by sodium and potassium. The methods of evaluation were used galvanostaticcycling and x-ray analysis (XRD).

Des matériaux d'électrode positive pour batteries Li-ion de formule Lix0(Co,M)O2 (M = Ni, Mg ; x0 ≥ 1.0) ont été préparés à haute température (900° C) et caractérisés par diffraction des rayons X, tests galvanostatiques, spectroscopie de RMN MAS du 7Li et mesures électriques. Alors que les propriétés de la phase LiCoO2 sont en accord avec la littérature, dans tous les cas, l'ajout d'un excès de lithium lors de la synthèse conduit dans le matériau final à la présence d'un défaut structural constitué de lacunes d'oxygène et d'ions Co3+ spin intermédiaire (Co3+(IS)) en site pyramidal à base carrée. Ce défaut influe considérablement sur les propriétés des phases désintercalées puisqu'il supprime toutes les transitions de phase habituellement observées lors du cyclage galvanostatique de la phase LiCoO2. La substitution du nickel au cobalt permet de séparer la contribution des ions NiIII et Co3+(IS) quant à la disparition des transitions de phase lors de la désintercalation du lithium. La substitution du magnésium au cobalt, même sans excès de lithium, induit systématiquement la présence de ce type de défaut (Co3+(IS)). Cette particularité a été corrélée au comportement électrochimique de ces matériaux Lix(Co,Mg)O2 en cyclage.

Among the obstacles for the commercialization of the MoltenCarbonate Fuel Cell (MCFC), the dissolution of thestate-of-the-art lithiated NiO cathode is considered as aprimary lifetime limiting constraint. Development ofalternative cathode materials is considered as a main strategyfor solving the cathode dissolution problem. LiFeO2and LiCoO2had earlier been reported as the most promisingalternative materials; however, they could not satisfactorilysubstitute the lithiated NiO. On the other hand, ternarycompositions of LiFeO2, LiCoO2and NiO are expected to combine some desirableproperties of each component. The aim of this work was todevelop alternative cathode materials for MCFC in the LiFeO2-LiCoO2-NiO ternary system. It was carried out byinvestigating electronic conductivity of the materials, firstin the form of bulk pellets and then in ex-situ sinteredporous-gas-diffusion cathodes, and evaluating theirelectrochemical performance by short-time laboratory-scale celloperations. Materials in the LiFeO2-NiO binary system and five ternary sub-systems,each with a constant molar ratio of LiFeO2:NiO while varying LiCoO2content, were studied. Powders withcharacteristics appropriate for MCFC cathode fabrication couldbe obtained by the Pechini method. The particle size of LiFeO2-LiCoO2-NiO powders considerably depends on thecalcination temperature and the material composition. Theelectrical conductivity study reveals the ability of preparingLiFeO2-LiCoO2-NiO materials with adequate electricalconductivity for MCFC cathode application. A bimodal pore structure, appropriate for the MCFC cathode,could be achieved in sintered cathodes prepared usingporeformers and sub-micron size powder. Further, this studyindicates the nature of the compromise to be made between theelectrical conductivity, phase purity, pore structure andporosity in optimization of cathodes for MCFC application. Cellperformance comparable to that expected for the cathode in acommercial MCFC could be achieved with cathodes prepared from20 mole% LiFeO2- 20 mole% LiCoO2- 60 mole% NiO ternary composition. It shows aniR-corrected polarization of 62 mV and a iR-drop of 46 mV at acurrent density of 160 mAcm-2at 650 °C. Altogether, this study revealsthe possibility of preparing LiFeO2-LiCoO2-NiO cathode materials suitable for MCFCapplication. Keywords: molten carbonate fuel cell (MCFC), MCFC cathode,LiFeO2-LiCoO2-NiO ternary compositions, electrical conductivity,porous gas diffusion electrodes, polarization, electrochemicalperformance, post-cell characterization.

<p>Among the obstacles for the commercialization of the MoltenCarbonate Fuel Cell (MCFC), the dissolution of thestate-of-the-art lithiated NiO cathode is considered as aprimary lifetime limiting constraint. Development ofalternative cathode materials is considered as a main strategyfor solving the cathode dissolution problem. LiFeO₂and LiCoO₂had earlier been reported as the most promisingalternative materials; however, they could not satisfactorilysubstitute the lithiated NiO. On the other hand, ternarycompositions of LiFeO₂, LiCoO₂and NiO are expected to combine some desirableproperties of each component. The aim of this work was todevelop alternative cathode materials for MCFC in the LiFeO₂-LiCoO₂-NiO ternary system. It was carried out byinvestigating electronic conductivity of the materials, firstin the form of bulk pellets and then in ex-situ sinteredporous-gas-diffusion cathodes, and evaluating theirelectrochemical performance by short-time laboratory-scale celloperations.</p><p>Materials in the LiFeO₂-NiO binary system and five ternary sub-systems,each with a constant molar ratio of LiFeO₂:NiO while varying LiCoO₂content, were studied. Powders withcharacteristics appropriate for MCFC cathode fabrication couldbe obtained by the Pechini method. The particle size of LiFeO₂-LiCoO₂-NiO powders considerably depends on thecalcination temperature and the material composition. Theelectrical conductivity study reveals the ability of preparingLiFeO₂-LiCoO₂-NiO materials with adequate electricalconductivity for MCFC cathode application.</p><p>A bimodal pore structure, appropriate for the MCFC cathode,could be achieved in sintered cathodes prepared usingporeformers and sub-micron size powder. Further, this studyindicates the nature of the compromise to be made between theelectrical conductivity, phase purity, pore structure andporosity in optimization of cathodes for MCFC application. Cellperformance comparable to that expected for the cathode in acommercial MCFC could be achieved with cathodes prepared from20 mole% LiFeO₂- 20 mole% LiCoO₂- 60 mole% NiO ternary composition. It shows aniR-corrected polarization of 62 mV and a iR-drop of 46 mV at acurrent density of 160 mAcm^-2at 650 °C. Altogether, this study revealsthe possibility of preparing LiFeO₂-LiCoO₂-NiO cathode materials suitable for MCFCapplication.</p><p>Keywords: molten carbonate fuel cell (MCFC), MCFC cathode,LiFeO₂-LiCoO₂-NiO ternary compositions, electrical conductivity,porous gas diffusion electrodes, polarization, electrochemicalperformance, post-cell characterization.</p>

The dissertation thesis deals with electrode materials and components for lithium-ion power sources. The thesis works with two different kinds of materials, concretely nanostructured Li4Ti5O12 with spinel basis and LiCoO2 with layered structure. The electrochemical properties, structure and element analysis and utilization possibilities in electrochemical industry of new technological electrode material Li4Ti5O12 were investigated. The influences of admixtures and electrolytes on characteristics of electrode materials with aforesaid active masses were also examined. Low cost price, environmental safety and obtained results of electrochemical measurements and structure analysis refer to wide possibilities of usage electrode material Li4Ti5O12 in the field of electrochemistry.

The magnificent development of on-board solutions for electronics has resulted in the race towards scaling down of autonomous micro-power sources. In order to maintain the reliability of miniaturized devices and to reduce the power dissipation in high density memories like CMOS RAM, localized power for such systems is highly desirable. Therefore these micro-power sources need to be integrated in to the electronic chip level, which paved the way for the research and development of rechargeable thin film batteries (TFB). A Thin film battery is defined as a solid-state electrochemical source fabricated on the same scale as and using the same type of processing techniques used in microelectronics. Various aspects of deposition and characterization of LiCoO2/LiPON/Sn thin film battery are investigated in this thesis. Prior to the fabrication of thin film battery, individual thin film layers of cathode-LiCoO2, electrolyte-LiPON and anode-Sn were optimized separately for their best electrochemical performance. Studies performed on cathode layer include theoretical and experimental aspects of deposition of electrochemically active LiCoO2 thin films. Mathematical simulation and experimental validation of process kinetics involved in sputtering of a LiCoO2 compound target have been performed to analyze the effect of process kinetics on film stoichiometry. Studies on the conditioning of a new LiCoO2 sputtering target for various durations of pre-sputtering time were performed with the help of real time monitoring of glow discharge plasma by OES and also by analysing surface composition, and morphology of the deposited films. Films deposited from a conditioned target, under suitable deposition conditions were electrochemically tested for CV and charge/discharge, which showed an initial discharge capacity of 64 µAh/cm2/µm. Studies done on the deposition and characterization of solid electrolyte layer-LiPON have shown that, sputtering from powder target can be useful for certain compounds like Li3PO4 in which breaking of ceramic target and loss of material are severe problems. An ionic conductivity of 1.1 x10-6 S/cm was obtained for an Nt/Nd ratio of 1.42 for a RF power density of 3 W/cm2 and N2 flow of 30 sccm. Also the reasons for reduction in ionic conductivity of LiPON thin films on exposure to air have been analyzed by means of change in surface morphology and surface chemistry. Ionic conductivity of 2.8 x10-6 S/cm for the freshly deposited film has dropped down to 9.9 x10-10 S/cm due to the reaction with moisture, oxygen and carbon content of exposed air. Interest towards a Li-free thin film battery has prompted to choose Sn as the anode layer due to its relatively good electrochemical capacity compared with other metallic thin films and ease of processing. By controlling the rate of deposition of Sn, thin films of different surface morphology, roughness and crystallinity can be obtained with different electrochemical performance. The reasons for excessive volume changes during lithiation/delithiation of a porous Sn thin film have been analyzed with the aid of physicochemical characterization techniques. The results suggest that the films become progressively pulverized resulting in increased roughness with an increase in lithiation. Electrochemical impedance data suggest that the kinetics of charging becomes sluggish with an increase in the quantity of Li in Sn-Li alloy. Thin film batteries with configuraion LiCoO2/LiPON/Sn were fabricated by sequential sputter deposition on to Pt/Si substartes. Pt/Cu strips were used as the current collector leads with a polymer packaging. Electrochemical charge/discharge studies revealed discharge capacities in the range 6-15 µAh/cm2/µm with hundreds of repeated cycles. TFB with a higher capacity of 35 µAh/cm2/µm suffered capacity fade out after 7 cycles, for which reasons were analyzed. The surface and cross-sectional micrographs of cycled TFB showed formation of bubble like features on anode layer reducing integrity of electrolyte-anode interface. The irreversible Li insertion along with apparent surface morphology changes are most likely the main reasons for the capacity fade of the LiCoO2/LiPON/Sn TFB.

No description available.

This article deals with properties of cathode material of lithium-ion cells study in term of active layer dependence. Aim of the work is to get familiar with problematics of cathode material production and diagnostics and to compare different active layer production methods. The opening of the work is concentrating on rechargeable batteries, mainly lithium-ion batteries and their electrode materials. Practical part is describing method of cathode material production and its characteristics.