Este trabalho apresenta uma metodologia de projeto de atuadores eletromagnéticos lineares inovadora para aplicação em sistemas de suspensão semiativa e ativa. A metodologia, apresentada na forma de fluxograma, define critérios para determinar os requisitos de força e curso que um atuador deve desenvolver considerando um sistema mecânico vibratório com um grau de liberdade com excitação harmônica de base quando o método de controle skyhook é aplicado. Um atuador eletromagnético linear de bobina móvel com duplo arranjo de quase-Halbach que apresenta elevada densidade de força, reduzida massa móvel, ausência de força de relutância e baixa ondulação de força é definido como estudo de caso. Um modelo numérico parametrizado em elementos finitos do comportamento eletromagnético de um passo polar do dispositivo é criado e analisado, considerando restrições dimensionais, com os objetivos de projeto definidos como: elevada densidade de força e reduzida ondulação de força com acionamento brushless CA. Com base no modelo de um passo polar do dispositivo, define-se o volume ativo que o mesmo deve apresentar e, a partir deste, todas as dimensões são definidas de forma a atender os requisitos de projeto. Uma vez definidas as dimensões do atuador com base no modelo eletromagnético, realiza-se a modelagem térmica numérica que permite avaliar qual a máxima densidade de corrente elétrica aplicável de forma que a temperatura, estipulada como máxima, nos enrolamentos não seja excedida. Ainda, a distribuição térmica permite determinar a temperatura de operação dos ímãs permanentes que têm curva de operação dependente da temperatura. A partir dos resultados da simulação térmica e do modelo eletromagnético para um passo polar, realizou-se o acoplamento eletromagnético-térmico por meio da correção das propriedades dos ímãs permanentes e aplicando uma densidade de corrente eficaz dependente das dimensões do modelo parametrizado. O modelo acoplado é simulado e analisado, de modo que as dimensões finais do atuador podem ser obtidas atendendo aos mesmos objetivos de projeto previamente mencionados, respeitando os limites de operação térmica. Adicionalmente, são apresentados modelos analíticos do comportamento eletromagnético e térmico do atuador que podem servir de base para implementação da metodologia proposta, se esta for baseada em modelos analíticos, e podem futuramente ser empregados para a aplicação de otimização matemática do dispositivo. Por fim, um protótipo do dispositivo é construído de forma a validar a metodologia proposta. Com este protótipo são realizados ensaios de densidade de fluxo magnético no entreferro, tensão induzida a vazio, força estática e ensaio dinâmicos com o dispositivo instalado em uma bancada de testes de vibrações controladas desenvolvida durante o projeto. Os resultados mostram a eficácia da metodologia proposta, uma vez que os resultados experimentais mostraram boa concordância com os resultados esperados. / This work presents an innovative linear electromagnetic actuator design methodology for application in semi-active and active suspension systems. The methodology, synthesized in a flowchart, sets criteria to determine requirements such as axial force and stroke that an actuator should develop considering a vibration system with one degree of freedom with harmonic base excitation when the skyhook control method is applied. A linear moving-coil electromagnetic actuator with dual quasi-Halbach arrays of permanent magnets that presents high force density, low moving-mass, no reluctance force and low force ripple is defined as a case study. A finite element numerical parameterized model that describes the electromagnetic behavior of one pole pitch of the device is created and analyzed, considering dimensional constraints, with the design objectives defined as: high force density and low ripple of force with brushless AC drive. Based on the model of one pole pitch of the device the active volume and all dimensions are defined in order to meet the design requirements. Once the actuator dimensions are defined, based on the electromagnetic model, a numerical thermal model was constructed, which allows to evaluate the maximum applicable electric current density so that the maximum temperature at the windings is not exceeded. Furthermore, the thermal distribution gives the operating temperature of the permanent magnets, which present performance highly dependent on temperature. With the results of the thermal simulation, the electromagnetic-thermal coupling is performed by correcting permanent magnet properties and by applying a parametric-dependent effective current density. The coupled model is simulated and analyzed so that the final dimensions of the actuator can be obtained with the same design objectives previously mentioned, while respecting thermal operating limits. In addition, the work presents analytical models of the electromagnetic and thermal behavior of the actuator that can be the basis for implementation of the proposed methodology, if it is based on analytical models, and can further be used for the application of mathematical optimization of the device. Finally, a prototype was built to validate the proposed method. Measurements were carried out to assess magnetic flux density in the air gap, open-circuit induced voltage, static force and dynamic tests with the device installed in a test bench that was developed during this work. The results show the effectiveness of the proposed method since experimental results have shown good agreement with the expected results.

This diploma thesis deals with a problem of spores venturia inaequlis recognition. These spores are captured on a special tape which is then analyzed using a microscope. The tape can be analyzed by a laboratorian or by the program Sporedetect v3. This program provides functions for complete picture processing and object recognition. In this diploma thesis, there are also described ways to automatically control a sliding stage of a microscope utilizing motorized translation stages and linear actuators. The information about automatic control of a microscope stage was obtained from catalogues of the companies Standa and Edmundoptics.

Design of linear actuator for parallel kinematic structure is described in this master´s thesis. The parallel kinematic structure is described in the first part. Open kinematics structure and close kinematics structure are compared. Their benefits and disadvantages are also mentioned. Construction of some parallel robots is illustrated. Linear actuators of different company are described. Mechanical parameters and construction of linear actuator are compared. Design of linear actuator is described in practical part of master´s thesis. A few variation of linear actuator are introduced. Individual variants are evaluated by Multicriteria Decisional Analysis and a final conception is selected. Final conception of linear actuator is elaborated. Reasons for selection of every part of linear actuator are given and basic mechanical calculation design part is made. FEA analysis of the structural part of linear actuator is made. Design of linear actuator is evaluated in the final part.

This master thesis aims to develop a test methodology for electromechanical linear actuators. A linear actuator acts as a linear motor, converting a power source to linear motion. The electromechanical linear actuator in this project has an electric motor as its power source and uses a rack and pinion system to transfer that power to linear motion.  The test methodology is to impose a force onto the rack of the actuator, to ensure that operation under a load scenario is within specification. To accomplish this, the design of a test rig implementation is analyzed. The test rig consists of the test unit, which is to be tested, the load unit, which is to provide the load force, and a control system for the load unit. The load unit is another linear actuator and is controlled via a load cell. The load cell gives out the load force being applied, and the controller gives out the corresponding appropriate motor command to the load unit to ensure the load force is as desired. This analysis is done through simulation of the setup. Viable options for the setup were first analyzed in order to implement the deemed promising options for a setup into a simulation environment. The simulation environment in this project was Simscape, an extension of MATLAB’s Simulink. In simulation the parameters for the test rig were rigorously analyzed, in order to determine acceptable thresholds. The primary load unit tested was another electromechanical linear actuator from Cascade Drives, the model A-100-8P. Two secondary setups, one using the same model as being tested, and another setup using two of the models being tested. Simulation found that the suggested options’ applied load force have a poor rise time, large overshoot and substantial oscillation errors. The primary source for this was determined to be the latency between load cell input, and motor command output in the controller. The poor metrics from the result could lead to problems when emergency braking, and with a long honing period, which would render most test data unusable.