The adsorbed layer morphology of a series of surfactants under different conditions has been examined primarily using atomic force microscopy (AFM). The morphologies of single and double chained quaternary ammonium surfactants adsorbed to mica have been characterised using AFM at concentrations below the cmc. Mixing these different types of surfactants systematically allowed a detailed examination of the change in adsorbed film curvature from the least curved bilayers through to most curved globules. From this study a novel mesh structure was discovered at curvatures intermediate to bilayers and rods. A mesh was again observed in studies examining the morphology change of adsorbed nonionic surfactant films on silica with variation in temperature. Other surfactant mixtures were also examined including grafting non-adsorbing nonionic surfactants and diblock copolymers into quaternary ammonium surfactant films of different morphologies.

Die E-Zigarette gewinnt in den letzten Jahren immer mehr an Popularität. Die Frage der Toxizität ist jedoch noch nicht abschließend geklärt, und es besteht weltweite Unsicherheit bei der Verwendung der E-Zigarette. Die vorliegende Arbeit untersucht menschliche Nasenschleimhautzellen nach Dampfexposition mit Propylenglykol, einem Hauptbestandteil der Liquide, auf mögliche akute Entzündungsreaktionen, zytotoxische und genotoxische Wirkungen. Die Nasenschleimhautzellen von 10 Probanden wurden im Air-Liquid-Interface kultiviert und anschließend verschiedenen Konzentrationen von Propylenglykol ausgesetzt. Die Analyse erfolgte unter Verwendung eines Trypanblau-Tests, eines Comet-Assays, eines Mikrokern-Tests und eines IL-6- und IL-8-Sandwich-ELISAs. Der Trypanblau-Test zeigte keine Reduktion der Vitalität. Im Sandwich-ELISA konnte kein Anstieg der IL-6- und IL-8-Konzentrationen festgestellt werden. Im Comet-Assay zeigte das Olive Tail Moment in allen untersuchten Konzentrationen eine Schädigung im Vergleich zur Negativkontrolle. Es zeigte sich auch eine dosisabhängige Schädigung. Ein Unterschied zwischen der Reinsubstanz und der Negativkontrolle konnte im Mikrokern-Test festgestellt werden. Es wurden reparierbare Schäden im Comet-Assay gefunden. Im Mikrokern-Test konnten diese nur in der Reinsubstanzkonzentration bestätigt werden. Die E-Zigarette sollte restriktiv verwendet werden, bis Langzeitstudien vorliegen. Darüber hinaus sollten die Hersteller die Inhaltsstoffe der Flüssigkeiten eindeutig angeben. / The e-cigarette has become increasingly popular in recent years. However, the question of toxicity has not yet been clarified and there is global uncertainty in the use of the e-cigarette. The present work investigates propylene glycol, a major component of the liquids, for possible acute inflammatory reactions, cytotoxic and genotoxic effects on human nasal mucosal cells. The nasal mucosal cells from 10 volunteers were cultivated in the air-liquid-interface and then exposed to different concentrations of propylene glycol. The analysis was carried out using a trypan blue test, comet assay, micronucleus test and IL-6 and IL-8 sandwich-ELISA. The trypan blue test showed no reduction in vitality. No increase in IL-6 and IL-8 concentrations could be detected in the sandwich ELISA. In the comet assay, the Olive Tail Moment showed damage compared to the negative control in all examined concentrations. There was also a dose-dependent damage. A difference between the pure substance and the negative control could be found in the micronucleus test. Repairable damage in the comet assay have been found. In the micronucleus test these could only be confirmed in the pure substance concentration. The e-cigarette should be used restrictively until long-term studies are available. In addition, the manufacturers should clearly declare the ingredients of the liquids.

Air bubbles are a promising means of controlling fouling for a range of applications, particularly delaying fouling in marine environments. This work investigates the mechanism by which the collision of an air bubble with a solid removes adsorbed bacteria. A key feature of the work is that the numbers of bacteria were monitored via video microscopy throughout the collision, so we were able to explore the mechanism of bacteria removal. When a bubble collides with a solid, an air–water interface crosses the solid twice, and we were able to distinguish the effects of the first and second air–water interface. The bacterium Pseudomonas aeruginosa was allowed to adhere to smooth polydimethylsiloxane (PDMS) and then a collision with a bubble was investigated for one of three different approach geometries: perpendicular, parallel, and oscillating parallel to the solid surface. Other factors examined were the speed of the bubble, the duration of bacterial adhesion on the solid surface, and the wettability of the solid. Surface wettability was identified as the most significant factor. When the solid dewets, almost all bacteria were removed from hydrophobic surfaces upon the passage of the first air–liquid interface. In contrast, when a thin liquid film remained between the solid and the bubble (a hydrophilic solid), variable amounts of bacteria remained. Although almost all bacteria were initially removed from hydrophobic solids, many bacteria were redeposited on hydrophobic surfaces upon the passage of the second air–liquid interface, especially when the first and second air–liquid interfaces moved in opposite directions. As described previously, a lower velocity of the bubble allows more time for the thin liquid film to drain, and improved removal efficiency on hydrophilic solids. A rougher solid (8 µm diameter hemispherical protrusions) decreased the detachment efficiency because bacteria and liquid were able to shelter in concavities. Air bubbles are capable of removing bacteria over a range of conditions and are a potentially efficient means of combating biofilm growth for practical applications. / Master of Science / A major problem for equipment submerged in seawater is their eventual coverage in marine organisms including bacteria, barnacles, seaweed, and algae. This work investigates how effectively an air bubble removes bacteria adhered to a submerged solid. Adhered bacteria were observed and counted throughout the interaction of a bubble with a solid. When a bubble collides with a solid and is then removed, the bubble edge passes over the solid twice. The edge of the bubble is referred to as an air–liquid interface. The effects on adhered bacteria removal of the first and second passes of the bubble air–liquid interface were observed. Pseudomonas aeruginosa, a bacterial species common to both marine and medical environments, was allowed to adhere to flat solids made up of the polymer polydimethylsiloxane (PDMS) prior to a collision with an air bubble. The air bubble was collided with the solid in three distinct ways: directly from above, across the solid surface in one direction, and across the solid surface in one direction before being pulled back in the other direction. The speed of the bubble, the amount of time bacteria were adhered to the solid prior to bubble collision, and the extent to which the solid could be wet were all also examined for their effects on adhered bacteria removal. The extent to which a solid surface could be dewetted was identified as the most significant factor. For solids that are easily dewetted, almost all adhered bacteria were removed with the passage of the first air–liquid interface. Many bacteria were then redeposited back onto the solid surface upon the passage of the second air–liquid interface, especially when it moved in a direction opposite to the first. In contrast, for solids that are easily wet by water, variable amounts of bacteria remained after the first air–liquid interface swept across its surface. Slower moving air–liquid interfaces were also shown to be more effective at removing adhered bacteria. Solid surfaces with rough patterning made it more difficult to remove bacteria. Air bubbles can be an effective method to combat adhered bacteria and potentially prevent eventual biological growth on different types of underwater applications.

Human practices have resulted in great damage to the environment. Carbon-depletion, water and air pollution, as well as global warming are examples of the environmental footprints caused by several industries and their related applications. Detergency (cleaning) is widely practiced operation in household, industry and institutional sectors and thus consumes significant amounts of water, energy and chemicals and, therefore, contributes appreciably to the environmental destruction. This process is still not fully understood, on a molecular level, and not acceptably optimised. Therefore, this study is a contribution toward a better fundamental understanding and optimisation of protein stain removal from interfaces, which may ultimately result in the development of environmentally friendly and sustainable cleaning products and technologies. In this research, the cleaning of rubisco, a grassy protein stain, from different surfaces (hydrophobic, hydrophilic, and dyed) using different cleaning agent formulations was investigated. These studies encompassed experimental work and fundamental analysis in terms of mathematical modelling. The results revealed a consistent correlation between enzyme adsorption kinetics and stain cleanability. Higher adsorption and desorption absolute rates ( a k and d k ) resulted in higher enzyme mobility and thus higher stain cleanability regardless of the enzyme adsorbed amount. Surface chemistry underlying the stain has indirectly influenced stain cleanability through the alteration of enzyme adsorption kinetics. Such fundamental findings may aid in screening enzyme candidates for detergent formulations and may also assist in designing easily cleanable surfaces. Another fundamental finding is the cooperative cleaning mechanism of surfactant and enzyme of rubisco stain from different interfaces. The break down of intermolecular physical bonds between interfacial rubisco molecules by surfactants and the break down of the intramolecular covalent bonds by enzyme resulted in a higher protein displacement from interfaces. The overall protein removal by the two different actions of surfactant and enzyme showed a superiority of a biosurfactant-enzyme formulation. This finding may have significant implications on developing sustainable detergents that have superior cleaning performance and no or minimal environmental hazard. Overall, the findings reported in this Ph.D. thesis may form a basis for further comprehensive scientific research, which may ultimately provide detergent market with more efficient and optimum cleaning products and technologies.

This dissertation addresses two topics associated with the assembly of surfactants at the solid-liquid interface for adsorption and materials synthesis. The first is the adsorption of an anionic fluorinated surfactant, tetraethylammonium perfluorooctylsulfonate (TEA-FOS), at the solid/liquid interface. Attenuated total reflection Fourier transform infrared spectroscopy is used to study the adsorption kinetics and average orientation of surfactants at the hydroxylated germanium surface. Atomic force microscopy provides complementary images of the adsorbed layer structure on mica. The adsorption follows unusual three-stage kinetics in which the rate of adsorption starts fast, slows as the surface becomes crowded, and then (surprisingly) accelerates due to nucleation of a heterogeneous multilayer structure. These fast-slow-fast three stage adsorption kinetics are observed for a wide range of concentrations at pH 6, and the rates of the three stages are modulated by pH and salt by tuning electrostatic interactions among surfactants, counterions, and the surface. The results suggest that tetraethylammonium mediates interactions between surfactants and with negatively charged surfaces. The dichroism measurements and AFM are consistent with a mechanism in which TEA-FOS first forms an incomplete layer with chains oriented randomly or somewhat parallel to the surface, followed by formation of flattened multilayer clusters with the chains oriented somewhat normal to the substrate. The second topic is the sol-gel synthesis of mesoporous silica materials using dual surfactant templates. Studies of templating with mixed cetyltrimethylammonium bromide and octyl-beta-D-glucopyranoside surfactants shows that the ternary phase diagram of surfactants in water can be used to predict mesoporous materials structure, and that vapor-phase ammonia treatments can either stabilize the structure or induce swelling by the Maillard reaction. Studies of sol-gel reaction-induced precipitation with demixed hydrocarbon and fluorocarbon cationic surfactant micelles show a wide variety of pore structures. A number of synthesis parameters are adjusted to tune the pore structure, for instance to adjust the size and populations of bimodal mesopores. Selective swelling of the two surfactants by liphophilic and fluorophilic solvents is observed. Finally, proteinaccessible hollow spherical silica particles with mesoporous shells are reported. The methods for engineering mesoporous materials reported here have potential applications in adsorption, controlled drug delivery and for catalysis.

Study of structural and particularly dynamical properties of the interface of water with graphite and rutile surfaces points towards anomalous behavior of water molecules close to solid matter. Evaluation of statistical properties like translational and rotational diffusivity, residence times and autocorrelation functions of orientation vectors indicates that the translation and rotation of water molecules can be not only hindered, but also facilitated, according to the particular local density, interactions and and geometrical structure of the surface. The newly developed methods for the measurement of statistical rotational properties near to liquid-solid boundary overcomes the difficulties that are closely related to the measurement of dynamical properties in strongly inhomogeneous environment in a way, that can be applied to other model systems of this type.

The toxicology of aerosols in occupational settings is often performed through particle collection on a filter followed by reconstitution into cell culture media which can alter the biological effects. Current in vitro exposure systems require additional instruments to control temperature and humidity, making the system bulky and difficult to take to the field. The Portable In Vitro Exposure Cassette (PIVEC) was designed for personal monitoring, characterized using copper nanoparticles, tested with alveolar cells, and set-up for real-time monitoring. Three differently sized copper nanoparticles, 40-800 nm, were dispersed as a dry aerosol and measured gravimetrically and on a number concentration basis to determine the deposition efficiency of the PIVEC. A549 cells, a human alveolar adenocarcinoma epithelial line, were exposed to the aerosols and oxidative stress and cell viability were monitored post-exposure. The deposition efficiency ranged from 0.5% to 18% depending on method of analysis and size of particle. Oxidative stress increased within the first two hours post exposure, however there was no significant difference in cell viability at the four hour time point at deposited doses up to 1.63 mg/cm2. Validation of the PIVEC was done in the laboratory using diesel exhaust. Metal oxide fuel additives are used to reduce emissions; however, additives have been shown to increase emitted nanoparticles. The PIVEC was used to determine the potential cytotoxicity and oxidative activity changes in A549 cells after exposure to either model particles or exhaust generated with or without a commercial, nano-cerium oxide based additive. Acellular experiments suggest a correlation between the deposition and the type of fuel used for the newly designed PIVEC. Cellular results suggest a decrease in cytotoxicity and no statistically significant effect on reactive oxygen species generation with the use of the nano-cerium oxide additive. Rapid monitoring of oxidative stress was performed using an enzyme-based biosensor. The functionalized biosensor uses cytochrome c to measure reactive oxygen species through electrochemical detection during aerosol exposures. When compared to a traditional biological assay, the biosensor response was similar. The PIVEC is a unique device, designed to monitor aerosols using air-liquid interface in vitro techniques including a real-time monitor for oxidative stress.

Molecular Dynamics (MD) simulations of nano-scale flows typically utilize fixed lattice crystal interactions between the fluid and stationary wall molecules. This approach cannot properly model thermal interactions at the wall-fluid interface. In order to properly simulate the flow and heat transfer in nano-scale channels, an interactive thermal wall model is developed. Using this model, the Fourier’s law of heat conduction is verified in a 3.24 nm height channel, where linear temperature profiles with constant thermal conductivity is obtained. The thermal conductivity is verified using the predictions of Green-Kubo theory. MD simulations at different wall wettability ( εωf /ε ) and crystal bonding stiffness values (K) have shown temperature jumps at the liquid/solid interface, corresponding to the well known Kapitza resistance. Using systematic studies, the thermal resistance length at the interface is characterized as a function of the surface wettability, thermal oscillation frequency, wall temperature and thermal gradient. An empirical model for the thermal resistance length, which could be used as the jump-coefficient of a Navier boundary condition, is developed. Temperature distributions in the nano-channels are predicted using analytical solution of the continuum heat conduction equation subjected to the new temperature jump condition, and validated using the MD results. Momentum and heat transfer in shear driven nanochannel flows are also investigated. Work done by the viscous stresses heats the fluid, which is dissipated through the channel walls, maintained at isothermal conditions. Spatial variations in the fluid density, kinematic viscosity, shear- and energy dissipation rates are presented. The energy dissipation rate is almost a constant for εωf /ε < 0.6, which results in parabolic temperature profiles in the domain with temperature jumps due to the Kapitza resistance at the liquid/solid interfaces. Using the energy dissipation rates predicted by MD simulations and the continuum energy equation subjected to the temperature jump boundary conditions developed in this study, the analytical solutions are obtained for the temperature profiles, which agree well with the MD results.

A novel strategy to investigate interfaces relevant to chromatographic separations is presented. The strategy in this dissertation relies on three key ideas: 1) design and fabrication of appropriate model of chromatographic interface, 2) use of forced dewetting to separate interfacial constituent of mobile phase from its bulk component yet preserves the interface, and 3) use of IR spectroscopy and ellipsometry to investigate the structure and thickness of isolated interface.Stratified structures of ultrathin (< 10 nm thick) silica films on gold using gold oxide as adhesive layer and wetting control agent are used as model solid phase. Such design provides chemical environment of bulk silica surface, does not introduce significant spectral background, is suitable for reflection-based spectroscopies, and allow for easy modification to mimic wide range of silica - solvent interfaces. Bare silica-water models capillary electrophoresis interfaces; water-methanol mixture at octadecylsilane-modified silica represents reversed phase liquid chromatography interfaces.Forced dewetting is used to decouple interfacial constituent of mobile phase from its bulk component; yet, the integrity of interface is preserved. This approach, combined with the use of IR spectroscopy and ellipsometry, allowed for ambient atmosphere characterization of these interfacial layers in terms of their structure, composition, and thickness for water at bare silica. Hydrogen bonding was probed in case of complex water-methanol binary mixture at octadecylsilane-modified silica surface.The analysis of residual water layers formed by forced dewetting at bare silica as a function of bulk solution pH shows that the structure of the interfacial layer is highly ordered compared to bulk, and is also pH dependent. Further, thicknesses of interfacial layers were found to be pH dependent and vary from ~6 (pH 1) to ~9 nm (pH 9). Gouy-Chapman-Stern double layer was found to be inadequate to satisfactorily describe observed trends. In addition, surface enhanced infrared absorbance phenomenon was also observed that aided increased quality of resulting IR spectra.The analysis of residual water-methanol layers formed by forced dewetting at octadecylsilane-modified silica surface as a function of gas phase atmosphere shows that the structure of the interfacial layer is highly dependent on the composition of gas phase. The observed changes indicate that condensation of methanol from gas phase into residual layer and/or evaporation of water from residual layer into gas phase may occur in used experimental setup used in this dissertation. For that reason, more precise quantification of relative amounts of water and methanol in residual layers was precluded. Yet, regardless of investigational conditions, two different hydrogen bonding environments for methanol were distinctively observed.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第23217号 / 工博第4861号 / 新制||工||1759(附属図書館) / 京都大学大学院工学研究科物質エネルギー化学専攻 / (主査)教授 作花 哲夫, 教授 安部 武志, 教授 佐藤 啓文 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DGAM