Emulsion explosives have become the preferred choice as blasting agents for numerous industries including mining, agriculture, and construction. One of the most important components in such an emulsion is an emulsifier, which controls the emulsification properties of the explosive. The present study involves the production of one such emulsifier, which is produced by reacting two immiscible liquids, PIBSA (polyisobutylene succinic anhydride) and MEA (monoethanolamine). The study examines the effect of design variable such as the impeller speed, impeller type and the dispersed phase volume fraction on interfacial area. Experiments were carried out in a 0.15 m diameter fully baffled stirred tank using a 6-bladed Rushton turbine impeller and a marine propeller. Drop size was determined using a microscope with a video camera and image processing system. The transient concentration of PIBSA was determined using FTIR analysis and used to estimate the volume fraction of the dispersed phase (ƒÖ). The effective interfacial area was calculated using the Sauter mean drop diameter, d32 and ƒÖ. Impeller speeds ranging from 150 to 600 rpm and dispersed phase volume fractions, ƒÖ ranging from 0.01 to 0.028 were examined in the experimental study. It was found that that the evolution of Sauter mean drop diameter, d32 has four different trends depending on ƒÖ and impeller speed. At high impeller speeds and high ƒÖ, d32 values decrease initially and reach constant values after a long period of time. This trend is consistent with the findings in previous investigations. Under certain operating conditions, d32 values increase initially with stirring time to reach a maximum value and then decrease to reach a steady state value. The presence of these trends has been attributed to the effect of changing physical properties of the system as a result of chemical reaction. Results indicate that, in general, Sauter mean drop diameter d32 decreases with an increase in agitation intensity. However a decrease in the dispersed phase volume fraction is found to increase d32. These trends are found to be the same for both impeller types studied. Comparing the drop size results produced by the two impellers, it appears that low-power number propeller produces s ignificantly smaller drops than the Rushton turbine. It was found that the concentrations of reactants decrease with time for all impeller speeds thereby leading to a decrease in interfacial area with the progress of the reaction. Interfacial area values obtained at higher impeller speeds are found to be lower in spite of lower d32 values at these speeds. Also, these values decrease with time and become zero in a shorter duration indicating the rapid depletion of MEA. The interfacial area values obtained with the propeller at a given impeller speed are lower as compared to those for Rushton turbine. They also decrease and become zero in a shorter duration as compared to those for Rushton turbine suggesting propeller¡¦s performance is better in enhancing the reaction rate.

Les procédés continus par rapport aux procédés batch sont réputés être plus surs, plus économiques et plus sélectifs. Au regard de ces avantages, de plus en plus d'industries opérant traditionnellement en batch s'orientent vers des procédés continus. Si beaucoup de recherches ont été menées dans ce domaine en chimie fine, il n'en est pas de même pour les procédés de polymérisation et plus particulièrement pour le procédé de polymérisation en suspension du chlorure de vinyle. Ce procédé est à l'heure actuelle un des procédés batch les plus aboutis tant il a subi d'améliorations au cours des dernières décennies sur les plan chimiques (recette) et technologiques. Cependant, l'exposition au chlorure de vinyle est extrêmement toxique et le procédé présente notamment toujours des limitations en transfert thermique inhérentes à la technologie batch. De plus, l'étape réactionnelle constitue la seule étape batch du procédé total de production. Eu égard a la formation des grains de PVC au cours de la réaction, le procédé peut-être divise en trois principales étapes : une étape de dispersion liquide-liquide dans laquelle les gouttelettes de monomères (diamètre moyen 30-50μm) sont formées et stabilisées, une étape de réaction qui s'accompagne d'un phénomène d'agglomération contrôlée des gouttelettes de monomères et au cours duquel les particules polymérisant s’avèrent collantes et une pure étape réactionnelle au cours de laquelle la polymérisation est menée jusqu'à la conversion désirée. La présente étude se propose d'identifier les technologies adaptées pour chacune des étapes identifiées. Compte tenu des connaissances actuelles sur le comportement et l'évolution des grains avec la conversion et après une étude bibliographique sur les procédés continus de polymérisation, les technologies choisies dans ce travail sont les mélangeurs statiques et différents design de colonnes pulsées utilisées à co-courant. L'étape de dispersion liquide-liquide a été étudiée a l’aide de trois technologies différentes pour des systèmes de phases modèles. Concernant les mélangeurs statiques, les études ont démontré leur capacité à obtenir des gouttelettes de taille contrôlée et de la taille désirée. Dans la gamme étudiée, aucun effet de la concentration en phase dispersée n'a été démontre sur la taille des gouttes. Le paramètre physico-chimique le plus influent est la tension interfaciale. Celle-ci a d'ailleurs été estimée aux temps courts, correspondant aux temps de séjour (40-100 ms) dans les mélangeurs statiques, en modifiant la technique de la goutte pendante. Les résultats en termes de diamètre de goutte ont été corrélés via les nombres adimensionnels caractéristiques du système et de l'écoulement, à savoir les nombres de Reynolds et de Weber. A la lueur de ces résultats, les mélangeurs statiques ont été installes au pilote industriel pour effectuer des chargements de réacteurs batch de polymérisation. En plus de réduire considérablement les temps de chargement, leur utilisation a montré une meilleure répartition des agents de suspension et de l'initiateur au sein du grain. Ensuite, deux design de colonnes pulsées ont été utilises : la colonne pulsée a disques et couronnes a co-courant ascendant vertical et le COBR (continuous oscillatory baffled reactor, Nitech). Pour le premier design, les influence du matériau de garnissage et de son agencement (type et hauteur), des paramètres physicochimiques (concentration en phase dispersée, tensioactifs) et des paramètres hydrodynamiques (débit total, amplitude et fréquence d'oscillation) sur la taille des gouttes obtenues ont été examinées. Avec le second design, seuls les paramètres hydrodynamiques ont été étudiés. Une corrélation sur la taille des gouttes est proposée en fonction de nombres adimensionnels caractéristiques de ces appareils. Les trois technologies génératrices de la dispersion sont alors comparées en termes d'énergie dissipée et de puissance dissipée. [...] / Continuous processes present the benefit to be safer and more cost saving than batch processes. Many researches have been carried out in fine chemistry but few contributions refer to polymerization. We focus on the vinyl chloride suspension polymerization. This process has been extensively studied in batch with lots of improvement regarding the formulation and the technologies. This polymerization process is highly complex due to the toxic nature of the monomer, the good manage of heat transfer and stirring. Moreover the reaction step remains the only batch step of the PVC production. According to the PVC grain formation, the process can be divided into three steps (i) a liquid-liquid dispersion step in which the monomer droplet (30-50 µm) are generated and stabilized, (ii) a controlled agglomeration step of the reacting droplets exhibiting a sticky behaviour, (iii) a reaction step until the conversion rate is around 80-90% and the particles size is stable. In this study, the different technologies suitable for the different steps are pointed out. Based on the state of the art of the grain behaviour depending on the reaction conversion and on the literature concerning polymerization continuous process, static mixers and different co-current pulsed columns are proposed. Three technologies with different model system were chosen to study the liquid-liquid dispersion step. Static mixers allow the control of the droplet size under turbulent flow. In the range of the operating conditions, the dispersed phase concentration does not have a significant effect on the droplet size. The interfacial tension appears to be the most significant physico-chemical parameters. Correlation to predict the mean droplet size is proposed depending on different dimensionless numbers based on the hydrodynamics and on the systems: the Reynolds and Weber numbers. Given the promising results, static mixers are implemented at pilot scale to load the batch prior to polymerization. Their use demonstrates a noticeable reduction of the loading time and a better homogenisation of the different suspending agents and initiator inside the PVC grain. The two co-current pulsed columns design studied are the discs and doughnuts pulsed column and the COBR (continuous oscillatory baffled reactor, Nitech). For the first one, the effect of the packing materials (type and height), of the physico-chemical parameters (dispersed phase concentration, surfactant) and of hydrodynamic parameters (flowrate and oscillation conditions) on the droplet size are investigated where as for the second one the study is limited to the hydrodynamic parameters. A mean droplet size correlation is proposed based on the characteristic dimensionless numbers. The three continuous contactors used for liquid-liquid dispersion are compared in term of energy dissipation rate. The reaction is carried out in a continuous tubular reactor (the pulsed column). The column is suitable to transport solid-liquid suspension. Vinyl acetate suspension polymerization is performed to demonstrate the feasibility and particularly to study the encrusting and fouling problem. The first results are very promising.

<p>In this research, liquid-liquid dispersion of viscous fluids was studied in an SMX static mixer in the laminar regime. Backlighting technique was used for flow visualization, and the Hough transform for circle detection was used in OpenCV to automatically detect and measure drop diameters for obtaining the size distribution. Silicone oil and an aqueous solution of high fructose corn syrup were used for dispersed and continuous phases respectively, and sodium dodecyl sulfate was used as the surfactant to modify the interfacial tension. Experiments were conducted at varying viscosity ratios and flow rates-each at zero, low (~200 ppm) and high (~1000 ppm) surfactant concentrations. The effect of holdup was explored only for a few cases, but it was found to have a minimal effect on the weighted average diameter D₄₃.</p> <p>It was found that the superficial velocity and the continuous phase viscosity had a dominant effect on D₄₃. The tail at the higher end of the droplet size distribution decreased with increasing superficial velocity and continuous phase viscosities. It was also found that D₄₃ decreased with lowering of the interfacial tension. Furthermore, the effect of the dispersed phase viscosity was significant only at non zero surfactant concentrations.</p> <p>An approximate model has been proposed that relates D₄₃ to the capillary number. It is based on an energy analysis of the work done by the viscous and surface forces on a drop of an initial diameter that is largely determined by the gap distance between the cross bars in the element</p> / Master of Applied Science (MASc)