<p>Li-ion batteries are not only a technology for the future, they are indeed already the technology of choice for today’s mobile phones, laptops and cordless power tools. Their ability to provide high energy densities inexpensively and in a way which conforms to modern environmental standards is constantly opening up new markets for these batteries. To be able to maintain this trend, it is imperative that all issues which relate safety to performance be studied in the greatest detail. The surface chemistry of the electrode-electrolyte interfaces is intrinsically crucial to Li-ion battery performance and safety. Unfortunately, the reactions occurring at these interfaces are still poorly understood. The aim of this thesis is therefore to increase our understanding of the surface chemistries and stability phenomena at the electrode-electrolyte interfaces for three novel Li-ion battery electrode materials.</p><p>Photoelectron spectroscopy has been used to study the surface chemistry of the anode material AlSb and the cathode materials LiFePO₄ and Li₂FeSiO₄. The cathode materials were both carbon-coated to improve inter-particle contact. The surface chemistry of these electrodes has been investigated in relation to their electrochemical performance and X-ray diffraction obtained structural results. Surface film formation and degradation reactions are also discussed.</p><p>For AlSb, it has been shown that most of the surface layer deposition occurs between 0.50 and 0.01 V <i>vs.</i> Li°/Li⁺ and that cycling performance improves when the lower cut-off potential of 0.50 V is used instead of 0.01 V. For both LiFePO₄ and Li₂FeSiO₄, the surface layer has been found to be very thin and does not provide complete surface coverage. Li₂CO₃ was also found on the surface of Li₂FeSiO₄ on exposure to air; this was found to disappear from the surface in a PC-based electrolyte. These results combine to give the promise of good long-term cycling with increased performance and safety for all three electrode materials studied.</p>

Li-ion batteries are not only a technology for the future, they are indeed already the technology of choice for today’s mobile phones, laptops and cordless power tools. Their ability to provide high energy densities inexpensively and in a way which conforms to modern environmental standards is constantly opening up new markets for these batteries. To be able to maintain this trend, it is imperative that all issues which relate safety to performance be studied in the greatest detail. The surface chemistry of the electrode-electrolyte interfaces is intrinsically crucial to Li-ion battery performance and safety. Unfortunately, the reactions occurring at these interfaces are still poorly understood. The aim of this thesis is therefore to increase our understanding of the surface chemistries and stability phenomena at the electrode-electrolyte interfaces for three novel Li-ion battery electrode materials. Photoelectron spectroscopy has been used to study the surface chemistry of the anode material AlSb and the cathode materials LiFePO4 and Li2FeSiO4. The cathode materials were both carbon-coated to improve inter-particle contact. The surface chemistry of these electrodes has been investigated in relation to their electrochemical performance and X-ray diffraction obtained structural results. Surface film formation and degradation reactions are also discussed. For AlSb, it has been shown that most of the surface layer deposition occurs between 0.50 and 0.01 V vs. Li°/Li+ and that cycling performance improves when the lower cut-off potential of 0.50 V is used instead of 0.01 V. For both LiFePO4 and Li2FeSiO4, the surface layer has been found to be very thin and does not provide complete surface coverage. Li2CO3 was also found on the surface of Li2FeSiO4 on exposure to air; this was found to disappear from the surface in a PC-based electrolyte. These results combine to give the promise of good long-term cycling with increased performance and safety for all three electrode materials studied.

<p>There are today clear indications that the Li-ion battery of the type currently used worldwide in mobile-phones and lap-tops is also destined to soon become the battery of choice in more energy-demanding concepts such as electric and electric hybrid vehicles (EVs and EHVs). Since the currently used cathode materials (typically of the Li(Ni,Co)O₂-type) are too expensive in large-scale applications, these new batteries will have to exploit some much cheaper transition-metal. Ideally, this should be the very cheapest - iron(Fe) - in combination with a graphite(C)-based anode. In this context, the obvious Fe-based active cathode of choice appears to be LiFePO₄. A second and in some ways even more attractive material - Li₂FeSiO₄ - has emerged during the course of this work.</p><p>An effort has here been made to understand the Li extraction/insertion mechanism on electrochemical cycling of Li₂FeSiO₄. A fascinating picture has emerged (following a complex combination of Mössbauer, X-ray diffraction and electrochemical studies) in which the material is seen to cycle between Li₂FeSiO₄ and LiFeSiO₄, but with the structure of the original Li₂FeSiO₄ transforming from a metastable short-range ordered solid-solution into a more stable long-range ordered structure during the first cycle. Density Functional Theory calculations on Li₂FeSiO₄ and the delithiated on LiFeSiO₄ structure provide an interesting insight into the experimental result.</p><p>Photoelectron spectroscopy was used to study the surface chemistry of both carbon-treated LiFePO₄ and Li₂FeSiO₄ after electrochemical cycling. The surface-layer on both materials was concluded to be very thin and with incomplete coverage, giving the promise of good long-term cycling.</p><p>LiFePO₄ and Li₂FeSiO₄ should both be seen as highly promising candidates as positive-electrode materials for large-scale Li-ion battery applications.</p>

There are today clear indications that the Li-ion battery of the type currently used worldwide in mobile-phones and lap-tops is also destined to soon become the battery of choice in more energy-demanding concepts such as electric and electric hybrid vehicles (EVs and EHVs). Since the currently used cathode materials (typically of the Li(Ni,Co)O2-type) are too expensive in large-scale applications, these new batteries will have to exploit some much cheaper transition-metal. Ideally, this should be the very cheapest - iron(Fe) - in combination with a graphite(C)-based anode. In this context, the obvious Fe-based active cathode of choice appears to be LiFePO4. A second and in some ways even more attractive material - Li2FeSiO4 - has emerged during the course of this work. An effort has here been made to understand the Li extraction/insertion mechanism on electrochemical cycling of Li2FeSiO4. A fascinating picture has emerged (following a complex combination of Mössbauer, X-ray diffraction and electrochemical studies) in which the material is seen to cycle between Li2FeSiO4 and LiFeSiO4, but with the structure of the original Li2FeSiO4 transforming from a metastable short-range ordered solid-solution into a more stable long-range ordered structure during the first cycle. Density Functional Theory calculations on Li2FeSiO4 and the delithiated on LiFeSiO4 structure provide an interesting insight into the experimental result. Photoelectron spectroscopy was used to study the surface chemistry of both carbon-treated LiFePO4 and Li2FeSiO4 after electrochemical cycling. The surface-layer on both materials was concluded to be very thin and with incomplete coverage, giving the promise of good long-term cycling. LiFePO4 and Li2FeSiO4 should both be seen as highly promising candidates as positive-electrode materials for large-scale Li-ion battery applications.

Dans cette thèse nous démontrons le travail fait sur deux matériaux de cathodes pour les piles lithium-ion. Dans la première partie, nous avons préparé du phosphate de fer lithié (LiFePO4) par deux méthodes de lithiation présentées dans la littérature qui utilisent du phosphate de fer (FePO4) amorphe comme précurseur. Pour les deux méthodes, le produit obtenu à chaque étape de la synthèse a été analysé par la spectroscopie Mössbauer ainsi que par diffraction des rayons X (DRX) pour mieux comprendre le mécanisme de la réaction. Les résultats de ces analyses ont été publiés dans Journal of Power Sources. Le deuxième matériau de cathode qui a été étudié est le silicate de fer lithié (Li2FeSiO4). Une nouvelle méthode de synthèse a été développée pour obtenir le silicate de fer lithié en utilisant des produits chimiques peu couteux ainsi que de l’équipement de laboratoire de base. Le matériau a été obtenu par une synthèse à l’état solide. Les performances électrochimiques ont été obtenues après une étape de broyage et un dépôt d’une couche de carbone. Un essai a été fait pour synthétiser une version substituée du silicate de fer lithié dans le but d’augmenter les performances électrochimiques de ce matériau. / In this thesis, we demonstrate work on two different cathode materials for lithium-ion batteries. First, the synthesis of lithium iron phosphate (LiFePO4) is reproduced from literature using two lithiation methods starting with amorphous iron phosphate (FePO4). For both reactions, the product at each step of the synthesis was analyzed using Mössbauer Spectroscopy and X-ray diffraction in order to gain further insight of the reaction mechanism. The results of this work were published in Journal of Power Sources. The second cathode material of interest was lithium iron silicate (Li2FeSiO4). A novel synthetic method was developed to produce lithium iron silicate cost effectively starting with low cost precursors and basic laboratory equipment. The material was synthesized using a solid- state synthesis after milling and carbon coating, electrochemical performance was evaluated. An attempt was made to synthesize off-stoichiometric lithium iron silicate in order to increase the electrochemical performance of the material.

Dans cette thèse nous démontrons le travail fait sur deux matériaux de cathodes pour les piles lithium-ion. Dans la première partie, nous avons préparé du phosphate de fer lithié (LiFePO4) par deux méthodes de lithiation présentées dans la littérature qui utilisent du phosphate de fer (FePO4) amorphe comme précurseur. Pour les deux méthodes, le produit obtenu à chaque étape de la synthèse a été analysé par la spectroscopie Mössbauer ainsi que par diffraction des rayons X (DRX) pour mieux comprendre le mécanisme de la réaction. Les résultats de ces analyses ont été publiés dans Journal of Power Sources. Le deuxième matériau de cathode qui a été étudié est le silicate de fer lithié (Li2FeSiO4). Une nouvelle méthode de synthèse a été développée pour obtenir le silicate de fer lithié en utilisant des produits chimiques peu couteux ainsi que de l’équipement de laboratoire de base. Le matériau a été obtenu par une synthèse à l’état solide. Les performances électrochimiques ont été obtenues après une étape de broyage et un dépôt d’une couche de carbone. Un essai a été fait pour synthétiser une version substituée du silicate de fer lithié dans le but d’augmenter les performances électrochimiques de ce matériau. / In this thesis, we demonstrate work on two different cathode materials for lithium-ion batteries. First, the synthesis of lithium iron phosphate (LiFePO4) is reproduced from literature using two lithiation methods starting with amorphous iron phosphate (FePO4). For both reactions, the product at each step of the synthesis was analyzed using Mössbauer Spectroscopy and X-ray diffraction in order to gain further insight of the reaction mechanism. The results of this work were published in Journal of Power Sources. The second cathode material of interest was lithium iron silicate (Li2FeSiO4). A novel synthetic method was developed to produce lithium iron silicate cost effectively starting with low cost precursors and basic laboratory equipment. The material was synthesized using a solid- state synthesis after milling and carbon coating, electrochemical performance was evaluated. An attempt was made to synthesize off-stoichiometric lithium iron silicate in order to increase the electrochemical performance of the material.