Abstract. The problem of Electromagnetic compatibility is a popular topic. It is divided into two categories, one is conducted electromagnetic interference, another is radiated interference. We can use LISN to measure the signal of conducted electromagnetic interference , and use antenna to measure the signal of radiated interference. This paper will focus on the antenna. The frequency range of radiated Electromagnetic Interference measurement is so wide that using the halfwave dipole antenna will be very time-consuming, Therefore broadband antennas are often used in lieu of the halfwave dipole antennas. The design procedure of the log-periodic dipole array antenna is introduced in this article. Simulation data of such antenna using the NEC2 software, including the input impedance and the antenna pattern are also provided. Furthermore, based on the parameters obtained from the simulation, a log-periodic dipole array antenna can be fabricated. In doing so, the simulation results should be modified to take into considerations of the specification of the material used, such as diameters of the materials, and lengths of the transmission lines. Once the construction of the log-periodic dipole array antenna is completes, it can be compared with the simulation results, and the difference between them should be investigated to find out the optimal design parameters. Finally, the antenna factor can be calculated to compare it with the measurement data.

Abstract Whether an Open Area Test Site (OATS) is qualified is based on the Normalized Site Attenuation (NSA). The purpose is to eliminate the influence of Antenna Factor (AF). Usually the AF provided by the manufacturer adopts the Standard Site Method (SSM) and is quoted from measurements at a 10-m range. In practice, the AF varies with the measurement conditions. This uncertainly will translate into error in NSA measurements. Currently radiated electromagnetic interference measurement mostly adopts the broadband antennas, and LPDA is one of the antennas used extensively. However, the AF provided by the manufacturer does not consider shifts in the phase center of LPDA with frequency. In the meantime the radiation pattern of LPDA is different from that of a short dipole. The investigation of this thesis will focus on these two parts. In determining the phase center of LPDA antenna we adopt the average shift of phase center to improve the AF. The numerical simulation results show that such an arrangement can result in improvement. We also use the method of PCPM (Phase Center and Pattern Matching) to modify the AF under different conditions of measurement when a ground plane is present. Our study, by using the numerical simulation and measurement, shows that this indeed improves the variation of AF over that obtained by SSM. In addition, efforts are also made to have a detailed discussion in mutually coupling effects between the LPDA antenna and the ground plane, in order to distinguish the impact on AF due to the coupling of the LPDA antenna and its image. Our numerical simulation results indicate that it does not have a significant effect.

Student Number : 9713144D - MSc Dissertation - School of Electrical Engineering - Faculty of Engineering and the Built Environment / The performance of the Log Periodic dipole array antenna has been characterized, in the form of parametric curves available in most antenna design handbooks and other relevant literature. These characteristic curves are often limiting in scope, as for instance they do not contain parametric curves giving the relationship between the boom-length 'L' and the number of dipole element 'N' for any given bandwidth, even when it is known that these two parameters are the main cost determinants of a LPDA Antenna. The concept of convergence is introduced to aid cost optimization of the LPDA Antenna in terms of number of dipole element 'N'. Although 'N' is used as the minimization criterion, the criteria for establishing convergence encompass all the main electrical characteristics of the LPDA Antenna, such as VSWR, gain and radiation patterns. Lastly, the effects of boomimpedance 'Zo' and length to diameter ration 'Ln/Dn', on the performance characteristics of the LPDA Antenna was investigated with the view to determining if neglecting the effects of these two parameters were responsible for the disparity in the directive gain values obtained by R. L Carrel compared to those obtained by later researchers. The investigation indicates that if an LPDA Antenna is converged, then the effects of Zo and Ln/Dn ratio though significant can not alone account for the fairly large disparity in the gain values. In other to perform these investigations, a modern scientific tool in the form of numerical modeling by method of moments based, Super Numerical electromagnetic code version2 was utilized. The numerical modeling tool was first validated by agreement between measured values and the values as predicted by the modeling tool. Next, simulation of the performance of LPDA antennas under variations of their number of elements was done. Thereafter, the means and standard deviations of the gain were extracted from the simulated numerical models. Trends in the pattern of variation of the means and standard deviations of the gain are used as the basis for deciding the value of number of element at which the antenna can yield acceptable performance (convergence criteria). These are presented as convergence curves, which gives for any given boom-length and operating bandwidth, the minimum number of elements required for the antenna to yield acceptable performance. Finally, the effect of length to diameter ratio and boom-impedance on the gain of optimized LPDA antennas are presented as parametric curves.