In diesem Report wird eine Niederenergie-Implantationskammer (NEI-Kammer) beschrieben, die im Forschungszentrum Rossendorf entwickelt und aufgebaut wurde. Die Kammer ermöglicht es, die Implantation von Ionen bei niedrigen Energien (< 30 keV) mit einer Implantationsanlage für mittlere Energien durchzuführen. In der Kammer werden der Ionenstrahl, den der Implanter liefert, auf die erwünschte niedrige Energie abgebremst. Dazu wird ein elektrostatisches Bremslinsensystem eingesetzt, das auf einem neuartigen Prinzip basiert. Das System besteht aus einer Sammellinse und einer Zerstreuungslinse, wobei die Öffnungsfehler beider Linsen entgegengesetzte Vorzeichen besitzen und sich gegenseitig kompensieren. Dadurch ist es möglich, Wafer gebräuchlicher Größe bei geringer Energie mit hoher Dosishomogenität zu implantieren. Die NEI-Kammer ist insbesondere für Forschungseinrichtungen eine vorteilhafte Lösung, da sie eine wesentlich kostengünstigere und flexiblere Alternative zur Anschaffung einer Niederenergie-Implantationsanlage darstellt.

To know your whereabouts is important and sometimes exact position is the determinant of success or not. Since the launch of the USA made Global Positioning System (GPS) in the late 1970s, global tracking has been available both for military and civilian use. Today, satellite based systems like the American GPS, European Galileo and the Russian GLONASS are the standard for basically any navigation or location application. However these systems are limited by the fact that they must have connection with multiple satellites in order to work. This means that satellite dependent systems are very limited in indoor environments. Despite this, there is no standard for indoor positioning systems (IPSs) even close to the satellite dependent systems when it regards distribution and accessibility for use where satellite dependent systems are limited or not working. However, this new age of connectivity provides a number of options for positioning indoors. There are some systems available, but very few of them provide good enough accuracy. This Master thesis evaluates different options for indoor positioning using technologies that are available in smart devices and smart phones, such as Wi-Fi and Bluetooth, and focuses on indoor positioning systems that can provide high accuracy. The current state of the technologies and the possible future for them, considering rising need and interest in indoor positioning systems are covered in this thesis. A selection of technologies and approaches are explored, tested in conditions designed for this purpose and evaluated to highlight their differences in approach, accuracy and usability. In order to achieve the goals of this thesis, a hybrid method of experimental research design and system development is selected as the main research method. The hybrid method is focused on experimental research, and is used to investigate if the accuracy of the positioning data can be affected and improved by tuning independent variables in an IPS. To be able to do this, an application for smart devices, such as android smartphones, is developed. The application developed is the heart of the conceptual crossover IPS (CCIPS), which is named Locantis, that is being developed and used in the experimental stages of this investigation. It is also used to test the hypothesis that a CCIPS could be a valid contender for replacing the established IPSs. The observations show how the accuracy and precision of the location data is affected by change to independent variables in an IPS and how well a CCIPS can meet real time requirement’s. The main conclusion is that changes to independent variables have greater impact on the precision than the accuracy for location data in an IPS and that a CCIPS in many cases are the sensible choice of IPS. / Att veta var du befinner dig är viktigt och ibland är exakt position avgörande för framgång. Sedan lanseringen av amerikanska Global Positioning System (GPS) i slutet av 1970 har global navigation varit tillgängliga för både militärt och civilt bruk. Idag är satellitbaserade system, som det amerikanska GPS, europeiska Galileo och det ryska GLONASS, standard för i princip alla navigering eller platsinformation. Men dessa system är begränsade av det faktum att de måste ha kontakt med flera satelliter för att fungera. Detta innebär att satellitberoende system är mycket begränsad i inomhusmiljöer. Trots detta finns det ingen standard för inomhus positioneringssystem (IPSS) som kan mäta sig med de satellitberoende systemen när det gäller distribution och tillgänglighet. Men denna nya generationens kommunikation ger ett antal alternativ för positionering inomhus. Det finns IPS tillgängliga idag, men väldigt få av dem kan tillhandahålla en hög noggrannhet på positioneringen. Detta examensarbete utvärderar olika alternativ för inomhuspositionering med teknologier som är tillgängliga i smarta enheter och smarta telefoner, som Wi-Fi och Bluetooth, fokus ligger på inomhus positioneringssystem som kan ge hög noggrannhet. Det aktuella läget för dessa teknologier och dess möjliga framtid, med tanke på stigande behov och intresse av inomhus positioneringssystem, behandlas i detta examensarbete. Ett urval av teknologier och metoder utforskas, testas under förhållanden utformade för detta ändamål, och utvärderas för att lyfta fram sina skillnader i tillvägagångssätt, noggrannhet och användbarhet. För att uppnå målen i detta examensarbete har en hybrid metod för experimentell designforskning och systemutveckling valts som huvudsaklig forskningsmetod. Hybridmetoden fokuserar på experimentell forskning och används för att undersöka om positioneringsdatas noggrannhet kan påverkas och förbättras genom att förändra oberoende variabler i ett IPS. För att kunna göra detta har en applikation för smarta enheter, så som Android, utvecklats. Applikationen som utvecklats är hjärtat i det konceptuella kombinations inomhuspositioneringssystem Locantis som utvecklas och används i det experimentella stadiet i denna undersökning. Den används också för att testa hypotesen att en CCIPS kunde vara en giltig kandidat för att ersätta den etablerade IPSer. Observationerna visa hur noggrannhet och precision av positioneringsdata påverkas av förändring på oberoende variabler i ett IPS och hur väl ett CCIPS kan uppfylla realtidskravet talet. Huvudslutsatsen är att förändringar på oberoende variabler har större inverkan på precision än noggrannheten för lokaliseringsuppgifter i en IPS och att ett CCIPS i många fall är det klokt val av IPS.

published_or_final_version / Physics / Master / Master of Philosophy

The Tin dioxide (SnO2) and Titanium dioxide (TiO2) are very promising materials in Material science. The SnO2 is commonly used as a gas sensor while the TiO2 is used as a catalyst in many reactions. Despite of the usefulness of these two substances, their surface structures lack detail investigations in the previous years. The Low Energy Electron Diffraction (LEED) technique is commonly used to characterize surfaces in the past 40 years, it is a mature system that many researches rely on its result. However, structural analysis in LEED requires comparison with computational results based on pre-defined structure models, which is a time-consuming method and the results are not guaranteed to be found. The direct determinations of structure by Patterson function inversion methods introduced by Huasheng Wu and S. Y. Tong could provide a different path to search for surface structure. In the Patterson function, each maximum in the function corresponds to a relative position vector of atomic pairs. Multiple-angle-incident LEED has to be performed to obtain an artifact-free Patterson function. Serveal SnO2 and TiO2 surfaces have been characterized by LEED and Patterson function inversion. SnO2 (110), (100), (101) , Rutile TiO2 (110), Anatase TiO2 (110) have been prepared by argon ion sputtering and annealing cycles and the cleanness has been checked by Auger Electron Spectroscopy and LEED. Reconstruction is observed based on the study of the LEED patterns. SnO2 (110) surface shows a 4 x 1 reconstruction in UHV environment while it gives 1 x 1 under annealing in oxygen and C(2 x 2) at higher annealing temperature afterward. SnO2 (100) , (101) and Rutile TiO2 (110) surfaces show 1 x 1 reconstruction in UHV environment and the reconstruction persists for further annealing. The Anatase TiO2 (110) surface shows a 3 x 4 reconstruction in UHV environment. The 3 x 4 reconstruction of Anatase TiO2 (110) surface would raise research interests as it is quite a special reconstruction. Multiple-angle-incident LEED has been performed on the SnO2 (100), (101) and Rutile TiO2 (110) surfaces. Patterson function inversion is performed on the surfaces SnO2 (100) and Rutile TiO2 (110) . Only LEED is performed on SnO2 (110) , (101) and Anatase TiO2 (110) surfaces. From Patterson functions analysis, the surface atoms positions are determined for the surface SnO2 (100) and Rutile TiO2 (110). The results show that their reconstructions are negligible, but they have obvious relaxations. / published_or_final_version / Physics / Master / Master of Philosophy

abstract / Physics / Doctoral / Doctor of Philosophy

No description available.

The ever-increasing quantity of by-products generated from burning coal in the production of electricity has brought about the need for new areas of utilization. This study examined the use of FGD gypsum and fluidized bed combustion ash along with Class F fly ash in the production of low-energy, 100% by-product cement blends. The cement blends used the advantageous properties of the by-product materials to create cementing properties rather than energy intensive clinker used in ordinary portland cement. The FGD gypsum was converted to hemihydrate which rapidly hydrated to provide the cement with early strength gains, whilst the fluidized bed combustion ash reacted with the Class F fly ash to form pozzolanic cementitious phases which provided the longer-term compressive strength and possibly resistance to weathering. The rate of compressive strength gains and minimizing detrimental expansion were two properties of particular interest in the study. Chemical admixtures were used to improve the compressive strengths of the cement mortars and decrease their solubility.

Symmetry tests and more precisely parity violation experiments using the properties of the weak interaction give us unique insight into the internal hadronic structure of matter. The Gº experiment at Jefferson Laboratory used parity violating electron scattering to probe the strange quark contribution to the electromagnetic nucleon form factors, (GMs and GEs) as well as the axial contribution, (GAe). The data taken during the experiment provide further information on the axial transition form factor of the N - $\Delta$ transition, (GANΔ), as well as the scale of the low energy constant (dΔ) characterizing the parity violating γNΔ coupling. The analysis of backward angle Gº data taken with a liquid deuterium target to deduce the parity violating asymmetry for pion photoproduction on the Δ resonance, and the first experimental constraint on the value of dΔ, are reported in this thesis. The results showed that dΔ = (8.3 ± 25.3) gπ where the uncertainty is dominated by statistics, and that 75 percent of the theory range would be excluded by this measurement at 1 sigma.

Symmetry tests and more precisely parity violation experiments using the properties of the weak interaction give us unique insight into the internal hadronic structure of matter. The Gº experiment at Jefferson Laboratory used parity violating electron scattering to probe the strange quark contribution to the electromagnetic nucleon form factors, (GMs and GEs) as well as the axial contribution, (GAe). The data taken during the experiment provide further information on the axial transition form factor of the N - $\Delta$ transition, (GANΔ), as well as the scale of the low energy constant (dΔ) characterizing the parity violating γNΔ coupling. The analysis of backward angle Gº data taken with a liquid deuterium target to deduce the parity violating asymmetry for pion photoproduction on the Δ resonance, and the first experimental constraint on the value of dΔ, are reported in this thesis. The results showed that dΔ = (8.3 ± 25.3) gπ where the uncertainty is dominated by statistics, and that 75 percent of the theory range would be excluded by this measurement at 1 sigma.

Building Simulation is widely used for understanding how a building consumes energy and for assessing design strategies aimed at improving building energy efficiency. The present research study uses eQUEST, a popular simulation software. Various simulations are done here to analyse and critically comment on the best design strategies to be used in order to vastly reduce the energy consumption of a recently constructed small (1800 m2 floor area) commercial building in Brampton, Ontario, which is a heating dominated region. The limitations faced with eQUEST while simulating the modified design are critiqued. A complete understanding of the building science and heat flow through the building envelope has been applied to modify the building in question. After all the changes applied, the overall heat load of the building was reduced to 15 kWh/m2/yr and the overall energy consumption reduced by 60 percent.