Two problems hampering efforts to produce salt-tolerant plants through constitutive expression of transgenes include: 1. Spatial control. Particular cell-types must respond specifically to salt stress to minimise the amount of Na⁺ delivered to the shoot; and, 2. Temporal control. Transgenes are typically expressed in plants at similar levels through time, irrespective of the stress encountered by the plant, which may exacerbate pleiotropic effects and means that, particularly in low-stress conditions, costly and/or detrimental metabolic processes may be active, thus reducing yield. To address these issues, Gateway® destination vector constructs were developed combining the GAL4 UAS (upstream activating sequence) with the ethanol-inducible gene expression system to drive inducible cell-specific expression of Na⁺ transporter transgenes (or to silence salt transporter transgenes inducibly and cell-specifically). Rice (Oryza sativa L. cv. Nipponbare) GAL4-GFP enhancer trap lines (Johnson et al., 2005: Plant J. 41, 779-789) that express GAL4 and GFP specifically in either the root epidermis or xylem parenchyma (and therefore ‘trap’ cell-type specific enhancer elements) were transformed with this GAL4 UAS – ethanol switch construct, thereby allowing both spatial and temporal control of transgenes. In preliminary experiments, the expression system successfully limited the expression of RFP to specific cell-types after induction with ethanol. Other genes expressed using this system include PpENA1, a Na⁺-extruding ATPase from the moss, Physcomitrella patens, and AtHKT1;1, a Na ⁺ transporter from Arabidopsis thaliana. The two enhancer trap rice lines were also transformed with the GAL4 UAS driving stable expression of AtHKT1;1 and PpENA1 specifically in root epidermal or xylem parenchyma cells. Expression of AtHKT1;1 in root epidermal cells reduced Na⁺ accumulation in the shoots, while expression in the root xylem parenchyma appeared to have little effect on shoot Na⁺ accumulation. Using cryo-scanning electron microscopy (SEM) X-ray microanalysis, the outer cells of the roots of the line expressing AtHKT1;1 in the epidermal cells were found to accumulate higher levels of Na⁺ than the parental enhancer trap line. Additionally, this line had decreased unidirectional ²²Na⁺ influx. Similar results were observed for plants expressing AtHKT1;1 driven by the CaMV 35S / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1325289 / Thesis (Ph.D.) -- University of Adelaide, School of Agriculture, Food and Wine, 2008

Two problems hampering efforts to produce salt-tolerant plants through constitutive expression of transgenes include: 1. Spatial control. Particular cell-types must respond specifically to salt stress to minimise the amount of Na⁺ delivered to the shoot; and, 2. Temporal control. Transgenes are typically expressed in plants at similar levels through time, irrespective of the stress encountered by the plant, which may exacerbate pleiotropic effects and means that, particularly in low-stress conditions, costly and/or detrimental metabolic processes may be active, thus reducing yield. To address these issues, Gateway® destination vector constructs were developed combining the GAL4 UAS (upstream activating sequence) with the ethanol-inducible gene expression system to drive inducible cell-specific expression of Na⁺ transporter transgenes (or to silence salt transporter transgenes inducibly and cell-specifically). Rice (Oryza sativa L. cv. Nipponbare) GAL4-GFP enhancer trap lines (Johnson et al., 2005: Plant J. 41, 779-789) that express GAL4 and GFP specifically in either the root epidermis or xylem parenchyma (and therefore ‘trap’ cell-type specific enhancer elements) were transformed with this GAL4 UAS – ethanol switch construct, thereby allowing both spatial and temporal control of transgenes. In preliminary experiments, the expression system successfully limited the expression of RFP to specific cell-types after induction with ethanol. Other genes expressed using this system include PpENA1, a Na⁺-extruding ATPase from the moss, Physcomitrella patens, and AtHKT1;1, a Na ⁺ transporter from Arabidopsis thaliana. The two enhancer trap rice lines were also transformed with the GAL4 UAS driving stable expression of AtHKT1;1 and PpENA1 specifically in root epidermal or xylem parenchyma cells. Expression of AtHKT1;1 in root epidermal cells reduced Na⁺ accumulation in the shoots, while expression in the root xylem parenchyma appeared to have little effect on shoot Na⁺ accumulation. Using cryo-scanning electron microscopy (SEM) X-ray microanalysis, the outer cells of the roots of the line expressing AtHKT1;1 in the epidermal cells were found to accumulate higher levels of Na⁺ than the parental enhancer trap line. Additionally, this line had decreased unidirectional ²²Na⁺ influx. Similar results were observed for plants expressing AtHKT1;1 driven by the CaMV 35S / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1325289 / Thesis (Ph.D.) -- University of Adelaide, School of Agriculture, Food and Wine, 2008

Two problems hampering efforts to produce salt-tolerant plants through constitutive expression of transgenes include: 1. Spatial control. Particular cell-types must respond specifically to salt stress to minimise the amount of Na⁺ delivered to the shoot; and, 2. Temporal control. Transgenes are typically expressed in plants at similar levels through time, irrespective of the stress encountered by the plant, which may exacerbate pleiotropic effects and means that, particularly in low-stress conditions, costly and/or detrimental metabolic processes may be active, thus reducing yield. To address these issues, Gateway® destination vector constructs were developed combining the GAL4 UAS (upstream activating sequence) with the ethanol-inducible gene expression system to drive inducible cell-specific expression of Na⁺ transporter transgenes (or to silence salt transporter transgenes inducibly and cell-specifically). Rice (Oryza sativa L. cv. Nipponbare) GAL4-GFP enhancer trap lines (Johnson et al., 2005: Plant J. 41, 779-789) that express GAL4 and GFP specifically in either the root epidermis or xylem parenchyma (and therefore ‘trap’ cell-type specific enhancer elements) were transformed with this GAL4 UAS – ethanol switch construct, thereby allowing both spatial and temporal control of transgenes. In preliminary experiments, the expression system successfully limited the expression of RFP to specific cell-types after induction with ethanol. Other genes expressed using this system include PpENA1, a Na⁺-extruding ATPase from the moss, Physcomitrella patens, and AtHKT1;1, a Na ⁺ transporter from Arabidopsis thaliana. The two enhancer trap rice lines were also transformed with the GAL4 UAS driving stable expression of AtHKT1;1 and PpENA1 specifically in root epidermal or xylem parenchyma cells. Expression of AtHKT1;1 in root epidermal cells reduced Na⁺ accumulation in the shoots, while expression in the root xylem parenchyma appeared to have little effect on shoot Na⁺ accumulation. Using cryo-scanning electron microscopy (SEM) X-ray microanalysis, the outer cells of the roots of the line expressing AtHKT1;1 in the epidermal cells were found to accumulate higher levels of Na⁺ than the parental enhancer trap line. Additionally, this line had decreased unidirectional ²²Na⁺ influx. Similar results were observed for plants expressing AtHKT1;1 driven by the CaMV 35S / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1325289 / Thesis (Ph.D.) -- University of Adelaide, School of Agriculture, Food and Wine, 2008

Made available in DSpace on 2014-10-09T12:43:32Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:58:20Z (GMT). No. of bitstreams: 1 06631.pdf: 7171449 bytes, checksum: 14579bbc0c3bfbe0058e6387b09d94f4 (MD5) / Dissertacao (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

La problématique des émissions de particules fines, posant des risques sanitaires et environnementaux avérés, a été très médiatisée ces dernières années. La solution mise en place consiste à aider financièrement les particuliers pour renouveler le parc d’appareils. Or, une utilisation non optimisée d’un appareil dégrade de manière significative ses émissions. Afin d’amender entre autres cette réflexion, de nombreuses campagnes expérimentales ont été menées au travers de caractérisations physico-chimiques complètes et innovantes des fumées, en particulier des particules fines : la Microscopie Electronique à Balayage, la microanalyse X et la détermination du type de carbone constitutif (Carbone Elémentaire, Carbone Organique). En premier lieu, la définition des paramètres d’utilisation de l’appareil et leurs niveaux de réponse ont permis de proposer une réduction significative des émissions dont celles de particules fines. Ainsi, les impacts des paramètres comme la nature du combustible, le mode d’allumage et l’injection d’air secondaire ont été quantifiés. Ensuite, les mécanismes de formations des particules ont été définis. Dans un second temps, ce travail de thèse s’est intéressé à l’évolution des caractéristiques des particules entre la chambre de combustion de l’appareil et le champ proche, permettant d’aller au-delà de l’étude normative classique. De nouveaux savoirs sur les particules ont ainsi été mis en évidence. L’ensemble de ces nouvelles connaissances, aidant à mieux connaître les particules produites par la combustion de bois dans des appareils indépendants, permettront dans le futur de créer des systèmes de traitement spécifiques et efficaces / The issue of the emissions of fine particles, known for their health and environmental hazards, has been significantly covered in recent years. The governments made the decision to help mainly financially the private individuals in order to renew the domestic appliances stock. However, a non-optimized use of an energy-efficient appliance can degrade system performances. In order to solve this issue, many experimental campaigns have been achieved through complete and innovative physicochemical characterizations of the smoke, especially of the fine particles : Scanning Electron Microscope, X-ray microanalysis and assessment of the constitutive Carbon (Elemental Carbon, Organic Carbon). First of all, the definition of the use parameters for the appliance and their impacts allowed offering a significant reduction of the fine particles emissions. In this work, the influences of the parameters such as the nature of the fuel, the ignition mode and the air secondary injection were in this way quantified. In order to better understand the origin of these emissions produced regardless of the combustion quality, the mechanisms of formation of all kinds of particles were defined. In a second phase, this work paid attention to the evolution of the characteristics of particles from the combustion room to the near-field. This enabled to go over the classic normative study. New knowledge on particles was brought to light, helping to better know the particles generation from domestic wood appliances. This could allow in the future to create some specific and efficient treatment systems

Made available in DSpace on 2014-10-09T12:42:49Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:08:07Z (GMT). No. of bitstreams: 0 / Tese(Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Made available in DSpace on 2014-10-09T12:43:32Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:58:20Z (GMT). No. of bitstreams: 1 06631.pdf: 7171449 bytes, checksum: 14579bbc0c3bfbe0058e6387b09d94f4 (MD5) / Dissertacao (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Made available in DSpace on 2014-10-09T12:42:49Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:08:07Z (GMT). No. of bitstreams: 0 / O NbAl3 e algumas ligas intermetálicas do sistema Nb-Ni-AI foram sintetizadas por combustão a partir dos pós de seus elementos constituintes. O efeito de variáveis de processo, como o tamanho de partícula dos pós, a composição química, a pressão de compactação, o tratamento de desgaseificação e a taxa de aquecimento, foram investigados na síntese do NbAl3 na forma de pastilhas cilíndricas. A síntese de ligas do sistema Nb-Ni-AI foi realizada a partir de misturas com as composições Nb10Ni70AI, Nb20Ni65AI e Nb30Ni60AI. A microestrutura das amostras reagidas foi caracterizada por microscopia óptica, microscopia eletrônica de varredura, EDS e difração de raios-X (método de Rietveld). Foram obtidas pastilhas de NbAl3 com 98,5 % da densidade teórica, superior ao valor encontrado na literatura (95%), mediante o controle de variáveis de processo. Nas pastilhas contendo níquel, a combustão ocorreu nas pastilhas de todas as composições. Fases metaestáveis, presentes na microestrutura das pastilhas baitas de reação, foram transformadas após tratamento térmico, originando ligas trifásicas com diferentes concentrações de fases (NbAl3, NiAI e NbNiAI), conforme a composição inicial do compactado. Algumas propriedades mecânicas de amostras brutas de reação e tratadas termicamente foram determinadas pela técnica da impressão (microdureza e tenacidade). Os resultados obtidos são comparáveis aos da literatura, salvo algumas discrepâncias atribuídas a processos de fabricação distintos. As etapas de reação da síntese do NbAl3 e de ligas Nb-Ni-AI foram posteriormente investigadas mediante interrupção da reação durante sua propagação ao longo de barras paralelepipédicas compactadas. Verificou-se que a síntese do NbAl3 ocorre pela dissolução de nióbio no alumínio fundido, seguida da precipitação do NbAl3. Nas amostras contendo níquel, a síntese ocorre em dois estágios: no primeiro estágio formam-se o Ni2Al3 ou o NiAl3, em quantidades relativas dependentes da composição geral. As reações deste primeiro estágio podem disparar as reações do segundo estágio, referentes à síntese do NbAl3. / Tese(Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN-SP

Submitted by Mery Piedad Zamudio Igami (mery@ipen.br) on 2017-03-10T14:48:40Z No. of bitstreams: 1 22057.pdf: 11251475 bytes, checksum: 0cbad14f90b9f9f9290ad688afbde04c (MD5) / Made available in DSpace on 2017-03-10T14:48:40Z (GMT). No. of bitstreams: 1 22057.pdf: 11251475 bytes, checksum: 0cbad14f90b9f9f9290ad688afbde04c (MD5) / O objetivo deste estudo foi a Y-TZP odontológica submetida ao envelhecimento hidrotérmico acelerado (EH). Especificamente: a) determinar a curva cinética de transformação de fase tetragonal para monoclínica; b) calcular a velocidade de crescimento da frente da camada transformada durante o EH; c) avaliar a relação entre a porcentagem de fase monoclínica e profundidade da transformação de fase com a resistência à flexão biaxial (FB); d) avaliar o efeito da associação do EH e fadiga na resistência à FB. Discos sinterizados (YZ- Vita YZ, LP-Lava Plus) foram submetidos ao EH a 120°C, 130°C e 150°C e analisados por difração de raios X (DRX). Uma amostra por grupo foi analisada por microscopia eletrônica de varredura (MEV) e tomografia de coerência óptica (OCT) para calcular a profundidade de transformação de fase e a velocidade da frente de transformação. Grupos de (YZ, LP e LA-Lava) foram submetidos ao EH (150°C) por (n=10): 0, 5, 25, 70 e 140 horas. Após o EH os grupos de YZ foram novamente divididos (n=10): com e sem ciclagem mecânica, todas as cerâmicas foram submetidas ao teste de flexão biaxial (ISO 6872) e análise de variância 1 fator (ANOVA) (α=0,05) para comparar os resultados. Os resultados de DRX indicam que a Y-TZP apresenta um comportamento sigmoidal de transformação de fase devido à limitação da profundidade de penetração dos raios X (~6,3 μm). As análises de MEV e OCT confirmaram o crescimento linear da frente de envelhecimento em função do tempo para todas as temperaturas. O ANOVA 1-fator demonstrou redução de 10-19% da resistência à FB após 140 horas de envelhecimento (150°C) para todas as cerâmicas, havendo correlação negativa entre profundidade da camada transformada e resistência à FB. Extrapolando os resultados de profundidade para 37°C foi calculado que a frente de transformação de fase levaria 1053 e 2104 anos para atingir a profundidade de 62,67μm e 85,55μm responsáveis pela diminuição da resistência mecânica da YZ e LP, respectivamente. A associação do EH com a ciclagem mecânica não apresentou efeitos deletérios para a YZ. O OCT foi validado como método preciso, fácil e rápido para avaliação da camada transformada e estudos de cinética. / Tese (Doutorado em Tecnologia Nuclear ) / IPEN/D / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP

O NbAl3 e algumas ligas intermetálicas do sistema Nb-Ni-AI foram sintetizadas por combustão a partir dos pós de seus elementos constituintes. O efeito de variáveis de processo, como o tamanho de partícula dos pós, a composição química, a pressão de compactação, o tratamento de desgaseificação e a taxa de aquecimento, foram investigados na síntese do NbAl3 na forma de pastilhas cilíndricas. A síntese de ligas do sistema Nb-Ni-AI foi realizada a partir de misturas com as composições Nb10Ni70AI, Nb20Ni65AI e Nb30Ni60AI. A microestrutura das amostras reagidas foi caracterizada por microscopia óptica, microscopia eletrônica de varredura, EDS e difração de raios-X (método de Rietveld). Foram obtidas pastilhas de NbAl3 com 98,5 % da densidade teórica, superior ao valor encontrado na literatura (95%), mediante o controle de variáveis de processo. Nas pastilhas contendo níquel, a combustão ocorreu nas pastilhas de todas as composições. Fases metaestáveis, presentes na microestrutura das pastilhas baitas de reação, foram transformadas após tratamento térmico, originando ligas trifásicas com diferentes concentrações de fases (NbAl3, NiAI e NbNiAI), conforme a composição inicial do compactado. Algumas propriedades mecânicas de amostras brutas de reação e tratadas termicamente foram determinadas pela técnica da impressão (microdureza e tenacidade). Os resultados obtidos são comparáveis aos da literatura, salvo algumas discrepâncias atribuídas a processos de fabricação distintos. As etapas de reação da síntese do NbAl3 e de ligas Nb-Ni-AI foram posteriormente investigadas mediante interrupção da reação durante sua propagação ao longo de barras paralelepipédicas compactadas. Verificou-se que a síntese do NbAl3 ocorre pela dissolução de nióbio no alumínio fundido, seguida da precipitação do NbAl3. Nas amostras contendo níquel, a síntese ocorre em dois estágios: no primeiro estágio formam-se o Ni2Al3 ou o NiAl3, em quantidades relativas dependentes da composição geral. As reações deste primeiro estágio podem disparar as reações do segundo estágio, referentes à síntese do NbAl3. / NbAl3 and Nb-Ni-AI intermetallic alloys have been obtained by pressureless combustion synthesis from elemental powders. The effects of process variables as powder particle size, composition, compaction pressure (green density), degassing treatment and heating rate on the combustion (thermal explosion mode) of NbAl3 cylindrical pellets were studied. Combustion synthesis of Nb-Ni-AI alloys was performed on powder mixtures with nominal compositions Nb10Ni70AI, Nb20Ni65AI and Nb30NI60AI. The microstructure of reacted samples was characterized by optical microscopy, scanning electron microscopy, EDS and X-ray diffraction (Rietveld method). It was shown that careful control of the processing conditions allowed near full (98,5%) dense pellets of NbAl3. In the nickel containing pellets, reaction occurred for all the compositions investigated. Metastable phases were seen to be present in the as reacted pellets, which were transformed after a heat treatment, producing a three phase alloy (NbAl3, NiAI and NbNiAI) with different phase concentrations, depending on the initial compact composition. Some mechanical properties, like microhardness and tenacity were measured by microidentation technique on the as reacted and heat-treated samples. The results are comparable with the literature, excepted for some discrepancies caused by different fabrication processes. The reaction sequence for both cases (NbAl3 and Nb-Ni-AI alloys) was further investigated by DSC analysis and also by interrupting the reaction during its propagation along compacted parallelopipedal bars. It was found that the NbAl3 synthesis occurs through niobium dissolution in molten aluminum and precipitation of NbAl3. In the nickel containing samples, synthesis occurs as two-stage reaction: Ni2Al3 or NiAl3 are formed in the first stage, with relative amounts depending on the general composition. This first stage reaction can trigger the second one, related to the formation of NbAl3.