Photonic links have been proposed to transport radio frequency (RF) signals over optical fiber. External optical modulation is commonly used in high performance RF-photonic links. The practical use of optical fiber to transport RF signals is still limited due to high RF signal loss. In order to reduce the RF signal loss, highly efficient modulators are needed. For many applications, modulators with broad bandwidths are required. However, there are applications that require only a narrow bandwidth. For these narrow-band applications, the modulation efficiency can be improved through the resonant enhancement technique at the expense of reduced bandwidth. The aim of this thesis is to investigate highly efficient Mach-Zehnder optical modulators (MZMs) on Lithium Niobate (LiNbO3) with resonant enhancement techniques for narrow-band RF-photonic applications. This work focuses in particular on analyzing the factors that affect the modulation efficiency through resonant enhancement so that the modulator electrode structure can be optimized for maximum modulation efficiency. A parameter study of the effects of the electrode characteristics on the modulation efficiency of resonantly enhanced modulators (RE-MZM) is provided. From this study, optimum design objectives are identified. Numerical optimization is employed to explore the design trade-offs so that optimal configurations can be found. A sensitivity analysis is carried out to assess the performance of optimal RE-MZMs with respect to the variations of fabrication conditions. The results of these investigations indicate that the RE-MZM with a large electrode gap is the optimal design since it provides high modulation efficiency although the inherent switching voltage is high, and is the most tolerant to the fabrication fluctuations. A highly efficient RE-MZM on X-cut LiNbO3 is practically demonstrated with the resonant enhancement factor of 5 dB when comparing to the unenhanced modulator with the same electrode structure and effective switching voltage of 2 V at 1.8 GHz. The performance of the RF-photonic link using the fabr icated RE-MZM is evaluated. Optimization of RE-MZMs for operating at millimeter-wave frequencies is also reported. Factors that limit the modulation efficiency of an RE-MZM at millimeter-wave frequencies are identified. Novel resonant structures that can overcome these limitations are proposed. Preliminary designs indicate that greatly improved modulation efficiency could be expected.

Inter-chip input-output (I/O) communication bandwidth demand, which rapidly scaled with integrated circuit scaling, has leveraged equalization techniques to operate reliably on band-limited channels at additional power and area complexity. High-bandwidth inter-chip optical interconnect architectures have the potential to address this increasing I/O bandwidth. Considering future tera-scale systems, power dissipation of the high-speed I/O link becomes a significant concern. This work presents a design flow for the power optimization and comparison of high-speed electrical and optical links at a given data rate and channel type in 90 nm and 45 nm CMOS technologies. The electrical I/O design framework combines statistical link analysis techniques, which are used to determine the link margins at a given bit-error rate (BER), with circuit power estimates based on normalized transistor parameters extracted with a constant current density methodology to predict the power-optimum equalization architecture, circuit style, and transmit swing at a given data rate and process node for three different channels. The transmitter output swing is scaled to operate the link at optimal power efficiency. Under consideration for optical links are a near-term architecture consisting of discrete vertical-cavity surface-emitting lasers (VCSEL) with p-i-n photodetectors (PD) and three long-term integrated photonic architectures that use waveguide metal-semiconductor-metal (MSM) photodetectors and either electro-absorption modulator (EAM), ring resonator modulator (RRM), or Mach-Zehnder modulator (MZM) sources. The normalized transistor parameters are applied to jointly optimize the transmitter and receiver circuitry to minimize total optical link power dissipation for a specified data rate and process technology at a given BER. Analysis results shows that low loss channel characteristics and minimal circuit complexity, together with scaling of transmitter output swing, allows electrical links to achieve excellent power efficiency at high data rates. While the high-loss channel is primarily limited by severe frequency dependent losses to 12 Gb/s, the critical timing path of the first tap of the decision feedback equalizer (DFE) limits the operation of low-loss channels above 20 Gb/s. Among the optical links, the VCSEL-based link is limited by its bandwidth and maximum power levels to a data rate of 24 Gb/s whereas EAM and RRM are both attractive integrated photonic technologies capable of scaling data rates past 30 Gb/s achieving excellent power efficiency in the 45 nm node and are primarily limited by coupling and device insertion losses. While MZM offers robust operation due to its wide optical bandwidth, significant improvements in power efficiency must be achieved to become applicable for high density applications.

Depuis plusieurs années, le volume de données échangé à travers le monde augmente sans cesse. Pour gérer cette large quantité d’information, des débits élevés de transmission de données sur de longues distances sont essentiels. Puisque les interconnections à base de cuivre ne peuvent pas suivre cette tendance, des systèmes de transmission optique rapides sont requis dans les centre de données. Dans ce contexte, la photonique sur silicium est considérée comme une solution pour obtenir des circuits photoniques intégrés à un coût réduit. Bien que cette technologie ait connu une croissance significative au cours de la dernière décennie, les transmetteurs actuels à haut débit de transmission sont principalement basés sur des sources laser externes. Par conséquent, l’objectif de ce travail de thèse était de concevoir et produire un transmetteur à haut débit de transmission de données pour la photonique sur silicium, doté d’une source laser intégrée.Ce transmetteur se compose d’un modulateur silicium de type Mach-Zehnder, co-intégré sur la même plaque avec un laser hybride III-V sur silicium à réseaux de Bragg distribués, dont la longueur d’onde d’émission peut être contrôlée électriquement autour de 1.3μm. La conception des différents éléments constituant à la fois le laser (coupleurs adiabatique entre le III-V et le silicium, miroirs de Bragg) et le modulateur (jonctions p-n, électrodes à ondes progressives) est détaillée, de même que leur fabrication. Pendant la caractérisation des transmetteurs, des taux de transmission de données jusqu’à 25Gb/s, pour des distances allant jusqu’à 10km ont été démontrés avec succès, avec la possibilité de contrôler la longueur d’onde jusqu’à 8.5nm. Par ailleurs, afin d’améliorer l’intégration de la source laser avec le circuit photonique sur silicium, une solution basée sur le dépôt à basse température (en-dessous de 400°C) d’une couche de silicium amorphe pendant la fabrication est aussi évaluée. Des tests sur une cavité laser à contre-réaction distribuée ont montré des performances au niveau de l’état de l’art (avec des puissances de sortie supérieures à 30mW), prouvant ainsi la viabilité de cette approche. / For several years, the volume of digital data exchanged across the world has increased relentlessly. To manage this large amount of information, high data transmission rates over long distances are essential. Since copper-based interconnections cannot follow this tendency, high-speed optical transmission systems are required in the data centers. In this context, silicon photonics is seen as a way to obtain fully integrated photonic circuits at an expected low cost. While this technology has experienced significant growth in the last decade, the high-speed transmitters demonstrated up to now are mostly based on external laser sources. Thus, the aim of this PhD thesis was to design and produce a high-speed silicon photonic transmitter with an integrated laser source.This transmitter is composed of a high-speed silicon Mach-Zehnder, co-integrated on the same wafer with a hybrid III-V on silicon distributed Bragg reflector laser, which emission wavelength can be electrically tuned in the 1.3μm wavelength region. The design of the various elements constituting both the laser (III-V to silicon adiabatic couplers, Bragg reflectors) and the modulator (p-n junctions, travelling-wave electrodes) is thoroughly detailed, as well as their fabrication. During the characterization of the transmitters, high-speed data transmission rates up to 25Gb/s, for distances up to 10km are successfully demonstrated, with the possibility to tune the operating wavelength up to 8.5nm. Additionally, in order to further improve the integration of the laser source with the silicon photonic circuit, a solution based on the low-temperature (below 400°C) deposition of an amorphous silicon layer during the fabrication process is also evaluated. Tests on a distributed feed-back laser structure have shown performances at the state-of-the-art level (with output powers above 30mW), thus establishing the viability of this approach.