A scaled-up gas turbine vane model was constructed in such a way to achieve a Biot number (Bi) representative of an actual engine component, and experiments were performed to collect temperature data which may be used to validate computational fluid dynamics (CFD) codes used in the design of gas turbine cooling schemes. The physical model incorporated an internal impingement plate to provide cooling on the inner wall surface, and film cooling over the external surface was provided by a single row of holes located on the suction side of the vane. A single row of holes was chosen to simplify the operating condition and test geometry for the purpose of evaluating CFD predictions. Thermocouples were used to measure internal gas temperatures and internal surface temperatures over a range of coolant flow rates, while infra-red thermography was used to measure external surface temperatures. When Bi is matched to an actual engine component, these measured temperatures may be normalized relative to the coolant temperature and mainstream gas temperature to determine the overall cooling effectiveness, which will be representative of the real engine component. Measurements were made to evaluate the overall effectiveness resulting from internal impingement cooling alone, and then with both internal impingement cooling and external film cooling as the coolant flow rate was increased. As expected, with internal impingement cooling alone, both internal and external wall surfaces became colder as the coolant flow rate was increased. The addition of film cooling further increased the overall effectiveness, particularly at the lower and intermediate flow rates tested, but provided little benefit at the highest flow rates. An optimal jet momentum flux ratio of I=1.69 resulted in a peak overall effectiveness, although the film effectiveness was shown to be low under these conditions. The effect of increasing the coolant-to-mainstream density ratio was evaluated at one coolant flow rate and resulted in higher values of overall cooling effectiveness and normalized internal temperatures, throughout the model. Finally, a 1-dimensional heat transfer analysis was performed (using a resistance analogy) in which overall effectiveness with film cooling was predicted from measurements of film effectiveness and overall effectiveness without film cooling. This analysis tended to over-predict overall effectiveness, at the lowest values of the jet momentum flux ratio, while under-predicting it at the highest values. / text

This study focused on experimentally measuring the performance of a fully cooled, scaled up C3X turbine vane. Experimental measurements focused on investigating row-to-row interactions of coolant jets and the contributions of external film cooling and internal impingement cooling to overall cooling effectiveness. Overall effectiveness was experimentally measured using a thermally scaled, matched Biot number vane model featuring a realistic internal impingement scheme and had normalized surface temperatures that were representative of those found on engine components. A geometrically identical vane was also constructed out of low conductivity polystyrene foam to measure the normalized adiabatic wall temperature, or adiabatic effectiveness of the film cooling configuration. The vanes featured a full coverage film-cooling scheme with a five-row showerhead and 13 total rows of holes containing 149 total coolant holes. This study was the first study to make highly detailed measurements of overall effectiveness on a fully-cooled vane model and expands on previous studies of adiabatic and overall effectiveness on the showerhead and single rows of holes on a matched Biot vane by considering a fully cooled configuration to determine if the results from these previous studies also hold for a fully cooled configuration. Additionally, velocity and thermal fields were measured just upstream of two different suction side rows of holes in order to study the effect of introducing upstream coolant injection. The effects of mainstream turbulence and span-wise location were examined and at the downstream row of holes, the contributions of different rows of holes to the approach flow were compared. This study was the first to measure mean and fluctuating velocity data on the suction side of a turbine vane with upstream coolant injection. Understanding the effects of how upstream injection affects the performance of downstream rows of holes is critical to understanding the film cooling performance on a fully cooled turbine airfoil. / text

This study performed detailed measurements on and around scaled up conducting and adiabatic airfoils with and without film cooling. The conducting vane was a matched Bi airfoil, which accurately scaled the convective heat transfer and conduction through the solid, in order to produce non-dimensional surface temperatures and thermal boundary layers that were representative of an actual engine. Measurements made on all vane models included surface temperature measurements and thermal profiles above the walls. Separate measurements on non-film cooled and film cooled conducting models allowed for the individual contributions of the internal convective cooling and external film cooling to the overall cooling scheme to be quantified. Surface temperature and thermal field measurements above the wall were also performed on a film cooled adiabatic model. For the conducting model with internal cooling only, strong streamwise temperature variations were seen. The surface temperature variations were highly dependent on the local external and internal heat transfer coefficients. Spanwise temperature variations also existed, but were modest in comparison to streamwise variations. Comparing the thermal fields above the film cooled adiabatic and conducting walls allowed for the assumption that the conducting wall would not significantly affect the thermal field in the film cooling jet to be tested. Near the edge of the film cooling jet the developing thermal boundary layer had a clear effect on the overlying gas temperature, suggesting that the common assumption that the adiabatic wall temperature is the appropriate driving temperature for heat transfer to a film cooled wall was invalid. On the jet centerline thermal boundary layer effects were less influential, due to the development of a new, thin boundary layer. This suggested that the adiabatic wall temperature as driving temperature for heat transfer was a reasonable assumption on the jet centerline for most cases tested. As film cooling momentum flux ratio increase, thermal boundary layer effects became more influential on the jet centerline. Additionally, the high resolution surface temperature measurements and thermal field measurements above the wall presented in the current study represent a significant improvement in the data available for validation of computational simulations of conducting turbine airfoils. / text