This thesis is a study of the heat transfer correlations between a wire and liquid helium cooled to either 1.9 or 4.3 K. The wire resembles a part of a superconducting magnet used in the Large Hadron Collider (LHC) particle accelerator currently being built at CERN. The magnets are cooled to 1.9 K and using helium as a coolant is very efficient, especially at extremely low temperatures since it then becomes a superfluid with an apparent infinite thermal conductivity. The cooling of the magnet is very important, since the superconducting wires need to be thermally stable. Thermal stability means that a superconductive magnet can remain superconducting, even if a part of the magnet becomes normal conductive due to a temperature increase. This means that if heat is generated in a wire, it must be transferred to the helium by some sort of heat transfer mechanism, or along the wire or to the neighbouring wires by conduction. Since the magnets need to be superconductive for the operation of the particle accelerator, it is crucial to keep the wires cold. Therefore, it is necessary to understand the heat transfer mechanisms from the wires to the liquid helium. The scope of this thesis was to describe the heat transfer mechanisms from a heater immersed in liquid and superfluid helium. By performing both experiments and simulations, it was possible to determine properties like heat transfer correlations, critical heat flux limits, and the differences between transient and steady-state heat flow. The measured values were in good agreement with values found in literature with a few exceptions. These differences could be due to measurement errors. A numerical program was written in Matlab and it was able to simulate the experimental temperature and heat flux response with good accuracy for a given heat generation.

<p>A 6082 aluminium alloy has been characterized with regard to the influence of surface roughness on fatigue strength.</p><p>Fatigue life testing of smooth specimens was used to establish reference curves for the material in extruded and forged T6 condition. The extruded material was found to have better fatigue strength than the forged material, although the cyclic stress-strain response was similar for both. The forged material was tested in T5, T6 and T7 tempers, showing no significant difference in fatigue strength.</p><p>Surface roughness was created by circumferential grinding of cylindrical test specimens, and the surface topography was measured using a white light interferometry microscope. The measurements proved to be accurate, although errors were observed for certain surface features. Residual stresses were quantified by X-ray diffraction. Compressive residual stresses of around 150 MPa were found in both rough and smooth specimens. Load cycling did not significantly alter the surface residual stresses.</p><p>Stress solutions ahead of all major surface grooves were found using a linear elastic material model. Estimates of cyclic stresses and strains were calculated in the notch roots using different Neuber corrections of the linear solution. The results were compared to finite element analysis employing a bilinear kinematic hardening model. A generalized version of the Neuber correction was found to be within 20% of the nonlinear finite element results.</p><p>Several empirical models for the notch sensitivity factor were investigated. These were found to be unable to describe the notch influence on fatigue life and initiation life. In order to follow this approach, it was recommended that different test specimens should be used where the short fatigue crack growth could be monitored.</p><p>It was shown that microstructural fracture mechanics theories could be used to estimate the fatigue limit of rough surfaces. In some cases, initiation from material defects or weaknesses would override the influence of surface geometry. In one specimen, the initiation appeared to have started as at a de-bonded grain, while in other cases, initiation was thought to have started at larger second phase particles embedded in notch roots. Further work in this area should focus on statistical descriptions of surface roughness, inherent material defects, and their interaction.</p>

A 6082 aluminium alloy has been characterized with regard to the influence of surface roughness on fatigue strength. Fatigue life testing of smooth specimens was used to establish reference curves for the material in extruded and forged T6 condition. The extruded material was found to have better fatigue strength than the forged material, although the cyclic stress-strain response was similar for both. The forged material was tested in T5, T6 and T7 tempers, showing no significant difference in fatigue strength. Surface roughness was created by circumferential grinding of cylindrical test specimens, and the surface topography was measured using a white light interferometry microscope. The measurements proved to be accurate, although errors were observed for certain surface features. Residual stresses were quantified by X-ray diffraction. Compressive residual stresses of around 150 MPa were found in both rough and smooth specimens. Load cycling did not significantly alter the surface residual stresses. Stress solutions ahead of all major surface grooves were found using a linear elastic material model. Estimates of cyclic stresses and strains were calculated in the notch roots using different Neuber corrections of the linear solution. The results were compared to finite element analysis employing a bilinear kinematic hardening model. A generalized version of the Neuber correction was found to be within 20% of the nonlinear finite element results. Several empirical models for the notch sensitivity factor were investigated. These were found to be unable to describe the notch influence on fatigue life and initiation life. In order to follow this approach, it was recommended that different test specimens should be used where the short fatigue crack growth could be monitored. It was shown that microstructural fracture mechanics theories could be used to estimate the fatigue limit of rough surfaces. In some cases, initiation from material defects or weaknesses would override the influence of surface geometry. In one specimen, the initiation appeared to have started as at a de-bonded grain, while in other cases, initiation was thought to have started at larger second phase particles embedded in notch roots. Further work in this area should focus on statistical descriptions of surface roughness, inherent material defects, and their interaction.

Enormous quantities of heat are available in air, soil, water, exhaust air from buildings, and in waste water of any kind. However these heat sources are use-less for heating purposes since their temperatures are lower than the tempera-ture required for heating. Heat pumps can be used to extract heat from these sources with a small expenditure of additional energy and up-grade and deliver the energy as useful heat for room heating. The heat pump cycle employs the well-known vapour compression cycle. The amount of heat delivered by a heat pump is equal to the amount of energy extracted from the heat source plus the heat equivalent to the compression work of the heat pump. Heat pumps, of course, are being generally accepted as outstanding energy saving units due their coefficient of performance (COP). Heat pumps for house heating have been used extensively in many countries and are especially common in Sweden. The annual growth rate of heat pump usage in Sweden is the same as in rest of Europe. According to the Swedish heat pump association, between 1986 to August 2003, the number of installed heat pump units in Sweden was 332,309. The demand for heat pumps started to increase from the year 1995 and in the year 2002, approximately 40,000 heat pump units were installed. Among the many types available, single-family heat pumps providing heating capacity of about 5 kW are widely popular. The main drawbacks of heat pumps are the complexity of the systems, high cost, need of technical knowledge, safety hazards and environmental effects of certain refrigerants, etc. An efficient heat pump with small refrigerant charge would have less of some of these drawbacks and could be a competitive alterna-tive to other heating processes. In this study, methods of refrigerant charge minimisation without reducing the performance of a small capacity (5 kW) heat pump have been investigated. Work has been focused on finding refrigerant charge distribution in different components of the heat pump, on finding out the solubility of refrigerant (pro-pane) with different compressor lubrications oils, on testing different types of compact heat exchangers, on constructing new minichannel heat exchangers and on finding correlations for calculating the heat transfer of minichannel heat exchangers. The results included in this thesis have been presented in four con-ference papers and five journal papers of which two were published and three were submitted for publication. / QC 20100707

As wind power expands rapidly worldwide, it is becoming more common to build wind farms in alpine locations where the wind resources often are good and conflicting interests are few. This is evident in Sweden where a substantial portion of the large wind parks planned are to be built in cold climate locations. The fact that icing of turbine blades and sensors can severely impact the production raises the question how large the losses are. In this thesis 10 wind parks comprising 45 turbines, well dispersed throughout Sweden are investigated. Daily production figures are compared to wind data from the MERRA reanalysis data-set in order to see if it is possible to determine the level of losses during the winter period caused by cold climate. A method is suggested where a relationship between daily production and daily average wind speed is established using representative summer days. This relationship is then used to calculate an expected production for the winter period. Losses are concluded as the difference between expected and actual production. The method did not produce a consistent and reliable result for the sites investigated. However, the method captures the overall trend with higher losses in the north of Sweden compared to the sites in the south where little or no icing is likely. At the sites where icing is expected, losses in the range of 10 to 20% of the annual production were calculated.

<p><!-- --></p><p>In the wake of the economic growth of the Chinese market the past couple of decades, the energy consumption has surged. One of the biggest consequences of the increased energy consumption is a massive increase in CO₂ emission. In fact, China has overtaken the U.S. as the biggest emitter of CO₂. In light of this energy-saving technology gets more important to implement. District heating is one of the solutions used with success in parts of China where heating is required. In this paper, an energy recovery technology has been examined for two climate zones in China namely a mechanical ventilation system using a flat-plate counter-flow heat exchanger. Beijing is located in a cold zone while Hong Kong is located in a zone with hot summers and mild winters. Cooling load calculations were conducted manually using the RTS - method developed by ASHRAE and heating load calculations were conducted for Beijing using Swedish guidelines stated in BBR. Further, the energy recovery unit (VM1) that was provided by Systemair AB was tested using a rig where different outdoor conditions were simulated. This data was then used to evaluate the potential for energy recovery in a model apartment located in the two zones. As expected, significant differences were obtained when comparing the performance for the two locations.</p><p> </p> / Redan avklarad

Increasingly intensive efforts are being made to enhance energy systems via augmented introduction of renewable energy along with improved energy efficiency. Resource constraints and sustained high fossil fuel prices have created a new phenomenon in the world market. Enhanced energy security and renewable energy development are currently high on public agenda worldwide for achieving a high standard of welfare for future generations. Biomass and municipal solid waste (MSW) have widely been accepted as important locally-available renewable energy sources offering low carbon dioxide (CO2) emissions. Concerning solid waste management, it has become a critical issue in Southeast Asia since the most popular form for waste disposal still employs open dumping and landfilling. While the need for a complete sustainable energy solution is apparent, solid waste management is also an essential objective, so it makes sense to explore ways in which the two can be joined. Electricity production in combination with energy recovery from flue gases in thermal treatment plants is an integral part of MSW management for many industrialized nations. In Sweden, MSW is considered as an important fuel resource for partially meeting EU environmental targets within cogeneration. However it is normally difficult to justify traditional cogeneration in tropical locations since there is little need for the heat produced. Similarly, MSW-fired cogeneration usually operates with low capacity during non-heating season in Sweden. Therefore, it is very important to find new alternatives for energy applications from waste, such as the implementation of thermally driven cooling processes via absorption cooling in addition to electricity production. The work presented herein concentrates first on an investigation of electricity generation from MSW power plants and various energy applications from waste in tropical urban areas. The potential for various types of absorption chillers driven by MSW power plants for providing both electricity and cooling is of particular interest. Additionally a demonstration and analysis of decentralized thermally driven cooling in district heating network supplied by low temperature heat from a cogeneration of MSW have been conducted. This study aims at developing the best system configuration as well as finding improved system design and control for a combination of district heating and distributed thermally driven cooling. Results show that MSW incineration has the ability to lessen environmental impacts associated with waste disposal, and it can contribute positively towards expanding biomass-based energy production in Southeast Asia. For electricity production, the proposed hybrid dual-fuel (MSW/natural gas) cycles feature attractive electrical efficiency improvements, leading to greenhouse gas emissions reduction. Cogeneration coupled with thermally driven cooling is a solution that holds promise for uniting enhanced sustainability with economic advantages. The system offers great opportunity for primary energy saving, increasing electrical yield and can significantly reduce CO2 emissions per unit of cooling as compared to compression chiller. The demonstration and simulation have also revealed that there is a potential with some modifications and improvements to employ decentralized thermally driven cooling in district heating networks even in temperate regions like Sweden. Thus, expanding cogeneration towards trigeneration can augment the energy supply for summer months in Europe and for year-round cooling in tropical locations. / QC 20110408

Secondary working fluids (secondary refrigerants, heat transfer fluids, antifreezes, brines) have long been used in various indirect re-frigeration and heat pump systems. Aqueous solutions (water solu-tions) have long been used as single phase (liquid only) secondary working fluids for cooling in supermarkets, ice rinks, heat recovery systems, heat pumps and other applications. However, aqueous solutions are increasingly used also for freezers in supermarkets and other applications in low temperature refrigeration. Of importance when comparing different secondary working fluids for indirect systems are the following basic thermophysical properties: freezing point, density, viscosity, specific heat, and thermal conductivity. Reliable data of these properties are needed to choose suitable fluid and to make technical calculations of an indirect refrigeration or heat pump system. The main intention of this work has been to select thermophysical property data with good or acceptable technical accuracy of a number of aqueous solutions that can be used by the refrigeration and heat pump industry, rather than focusing on a limited number of property values or scientifically very accurate measuring techniques. A thorough literature search was in view of this made to find the most reliable property values of aqueous solutions. Detailed literature references are given for thermo-physical properties of the following aqueous solutions, without other additives: Ethylene and propylene glycol, ethyl and methyl alcohol, glycerol, ammonia, potassium carbonate, calcium, lithium, magnesium and sodium chlorides as well as potassium acetate and potassium formate. Some laboratory measurements were made of most of the fluid types when literature values were incomplete or deemed unreliable. Methods used are briefly described and results are given. Much of the work was reported on in the Engineering Licentiate Thesis: Thermophysical properties of liquid secondary refrigerants, A Critical Review on Literature References and Laboratory Measure-ments (Melinder 1998a). That material forms the basis for the charts and tables used in the IIR-publication Thermophysical properties of liquid secondary refrigerants (Melinder, 1997). The present thesis reports on an update made since 1998, including re-view work done on two additional fluids not covered in Melinder (1998a). The thesis describes how the selection of property values results in tables and charts intended for the industry. Coefficients for poly-nomial equations are generated from these property values using a Matlab program and this material is intended as a useful tool for computer treatment. Aqueous solution of ethyl alcohol is used as example to see how this process is made. This choice of fluid can also be seen as a test of this method, as the basic thermophysical properties of aqueous solutions of ethyl alcohol present more chal-lenges than the other fluids examined. A comparison is made of a few types of aqueous solutions used as secondary working fluids for two types of applications. The first example is bedrock heat pumps and the second is cooling cabinets in a supermarket. An effort is made to see how the additive con-centration affects the thermal performance. Most aqueous solutions used as single-phase secondary fluids can also be used as ice slurry, a fluid consisting of liquid and ice where small ice crystals are produced, usually with some type of ice generator. The ice crystals are then transported to the cooling object from which heat is removed when ice crystals melt. This results in less temperature change in the cooling object and makes it also possible to reduce the volume flow rate and to use smaller pipe dimensions in the system. In order to choose a secondary fluid for ice slurry use and to make correct technical calculations of the ice slurry system there is a need to examine and evaluate thermo-physical properties and other aspects of ice and of the aqueous solution used. For dimensioning purposes it is of interest to estimate ice mass fraction and enthalpy values and enthalpy-phase diagrams can serve that purpose. This thesis presents enthalpy-phase diagrams made by author that besides isotherms contain lines with ice fraction and lines connecting enthalpies at freezing point and 1, 2, etc. to 10 K below the freezing point curve. / QC 20100609

Microchannel heat exchangers present many advantages, such as reduced size, high thermal efficiency and low fluid inventory; and are increasingly being used for heat transfer in a wide variety of applications including heat pumps, automotive air conditioners and for cooling of electronics.However, the fundamentals of fluid flow and heat transfer in microscalegeometries are not yet fully understood. The aim of this thesis is to contribute to a better understanding of the underlying physical phenomena in single-phase and specially flow boiling heat transfer of refrigerants in small channels. For this purpose, well-characterized heat transfer experiments have been performed in uniformly heated, single, circular, vertical channels ranging from 0.64 to 1.70 mm in diameter and using R-134a, R-22 and R-245fa as working fluids. Furthermore, flow visualization tests have been carried out to clarify the relation between the two-phase flow behavior and the boiling heat transfer characteristics. Single-phase flow experiments with subcooled liquid refrigerant have confirmed that conventional macroscale theory on single-phase flow and heat transfer is valid for circular channels as small as 640μm in diameter. Through high-speed flow boiling visualization of R-134a under non adiabatic conditions seven flow patterns have been observed: isolated bubbly flow, confined bubbly flow, slug flow, churn flow, slug-annular flow, annular flow, and mist flow. Two-phase flow pattern observations are presented in the form of flow pattern maps. Annular-type flow patterns are dominant for vapor qualities above 0.2. Onset of nucleate boiling and subcooled flow boiling heat transfer of R-134a has been investigated. The wall superheat needed to initiate boiling was found as large as 18 ºC. The experimental heat transfer coefficients have been compared to predictions from subcooled flow boiling correlationsav ailable in the literature showing poor agreement. Saturated flow boiling heat transfer experiments have been performed with the 640 μm diameter test section. The heat transfer coefficient has been found to increase with heat flux and system pressure and not to change with vapor quality or mass flux when the quality is less than ∼0.5. For vapor qualities above this value, the heat transfer coefficient decreases with vapor quality. This deterioration of the heat transfer coefficient is believed to be caused by the occurrence of intermittent dryout in this vapor quality range. The experimental database, consisting of 1027 data points, has been compared against predictions from correlations available in the literature. The best results are obtained with the correlations by Liu and Winterton (1991) and by Bertsch et al. (2009). However, better design tools to correctly predict the flow boiling heat transfer coefficient in small geometries need to be developed. Dryout incipience and critical heat flux (CHF) have been investigated in detail. CHF data is compared to existing macro and microscale correlations. The comparison shows best agreement with the classical Katto and Ohno (1984) correlation, developed for conventional large tubes. / QC 20101101

<!-- --> In the wake of the economic growth of the Chinese market the past couple of decades, the energy consumption has surged. One of the biggest consequences of the increased energy consumption is a massive increase in CO2 emission. In fact, China has overtaken the U.S. as the biggest emitter of CO2. In light of this energy-saving technology gets more important to implement. District heating is one of the solutions used with success in parts of China where heating is required. In this paper, an energy recovery technology has been examined for two climate zones in China namely a mechanical ventilation system using a flat-plate counter-flow heat exchanger. Beijing is located in a cold zone while Hong Kong is located in a zone with hot summers and mild winters. Cooling load calculations were conducted manually using the RTS - method developed by ASHRAE and heating load calculations were conducted for Beijing using Swedish guidelines stated in BBR. Further, the energy recovery unit (VM1) that was provided by Systemair AB was tested using a rig where different outdoor conditions were simulated. This data was then used to evaluate the potential for energy recovery in a model apartment located in the two zones. As expected, significant differences were obtained when comparing the performance for the two locations. / Redan avklarad