Thesis (PhD)--Stellenbosch University, 2002. / Some digitised pages may appear illegible due to the condition of the original hard copy. / ENGLISH ABSTRACT: Membrane fouling is universally accepted as one of the most critical problems limiting the wider application of membranes in liquid separations. The development and utilization of a suitable non-invasive technique for the on-line monitoring of fouling in industrial and laboratory applications may enable the effectiveness of fouling remediation and cleaning strategies to be quantified. The overall objective of this research is to develop ultrasonic time-domain reflectometry (UTDR) and its use as an analytical tool for the real-time study of inorganic-, organic- and protein- fouling of various types of membranes including nylon, polysulfone (PSU) and polyethersulfone (PESU) and modules, including flatsheet and tubular types. Different separation systems including microfiltration (MF) and ultrafiltration (UF), flat-sheet and tubular modules, and suitable ultrasonic probes were used in this study. Results of this study show a good correlation between the UTDR signal response and the development of a fouling layer on a membrane surface. UTDR effectively detected the appearance, growth and movement of a fouling layer echo as fouling proceeded. Cake (fouling)-layer compressibility was observed by UTDR. The structure and compaction of an asymmetric PSU membrane could be detected by UTDR. UTDR was also successfully used for monitoring membrane cleaning and evaluating the cleaning effectiveness o f various cleaning methods. UTDR results corroborated the flux measurements and SEM analyses. The ultrasonic unit is a programmed microprocessor, and can be used to compare reference and test signals to produce a differential signal (a fouling layer echo). A differential signal indicates the state and progress o f a fouling layer on the membrane surface in actual operations. Both amplitude and arrival time of differential signals as a function of operation time provide useful quantitative information, i.e. changes in thickness and density of a fouling layer, on the fouling processes. A predictive modelling program, ultrasonic reflection modelling (URM), was developed to describe the processes of ultrasonic testing related to the deposition of fouling layers on membrane surfaces. The mathematical model could substantiate changes in the densities of the fouling layer as well as the thickness. This is important as deposit resistance to flow is related to both thickness and density (compressibility). The predicted results of cake layer deposition are in good agreement with the actual UTDR measurements obtained in MF and UF. Furthermore, protein fouling was successfully detected in tubular UF by UTDR. Ultrasonic frequency spectra could be used as an additional tool for fouling detection. / AFRIKAANSE OPSOMMING: Membraan-aanvuiling of -verstopping is die grootste struikelblok wat die meer algemene aanwending van membrane vir verskillende watersuiweringsprosesse beinvloed. Die ontwikkeling en gebruik van ‘n geskikte nie-inmengende tegniek vir die in-lyn meting van aanvuiling van membrane in laboratorium-en nywerheidstoepassings mag ‘n geleentheid bied vir die kwantifisering van die verwydering van aanvuiling en skoonmaakstrategiee. Die hoofdoel van hierdie studie was die ontwikkeling van ultrasoniese tydgebiedsweerkaatsing (Eng: ultrasonic time-domain reflectometry, UTDR) en die gebruik daarvan as ‘n analitiese metode vir die studie van anorganiese-, organiese- en bio-besoedeling op verskeie tips membrane, insluitend nylon, polisufoon (PSU) en polietersulfoon (PESU), in beide platvel- en buismodules. Verskeie skeidingsisteme, insluitend mikrofiltrasie (MF) en ultrafiltrasie (UF) is ontwerp en gebruik in hierdie studie. Eksperimentele resultate het goeie ooreenstemming tussen die UTDR seinrespons en die ontwikkeling van ‘n aanvuilingslaag op die membraanoppervlakte bewys. Die ultrasoniese tegniek kon die vorming, groei en beweging van ‘n bevuilingslaagterugkaartsing waarneem namate bevuiling vorder. Aanvuilingslaagsamepersing is deur UTDR waargeneem. Die struktuur en samepersing van ‘n asimmetriese PSU membraan is ook deur UTDR gesien. UTDR is verder suksesvol gebruik om die skoonmaak van membrane te monitor en om die skoonmaakgeskiktheid (cleaning effectiveness) van verskeie skoonmaakmetodes te bepaal. UTDR resultate het permeaatvloeimetings en SEM analyses bevestig. Die ultrasoniese eenheid is ‘n geprogrameerde mikroverwerker, en kan gebruik word om verwysings- en toetsseine te vergelyk, en dan ‘n differensiaalsein te gee (‘n aanvuilingslaagweerklank). ‘n Differensiaalsein dui die toestand en vordering van ‘n aanvuilingslaag op die membraanoppervlakte gedurende gebruik aan. Beide amplitude asook aankomstyd van differensiaalseine as funksies van gebruikstyd verskaf bruikbare kwantatiewe inligting, dws. Veranderings in die dikte en digtheid van ‘n aanvuilingslaag, op die aanvuilingsproses. ‘n Voorspellingsmodelleringprogram - ultrasonieseweerkaatsingsmodellering (Eng: ultrasonic reflection modeling, URM) is ontwikkel om die proses van ultrasoniese toetsing by die deponering van aanvuilingslae op membraanoppervlaktes beter te beskryf. Veranderings in die digtheid en dikte van die aanvuilingslaag teenvloei is verwant aan dikte en digtheid (saampersbaarheid). Die voorspelde resultate van aanvuilingslaagdeponering stem goed ooreen met die werklike UTDR-metings wat in MF en UF gemaak is. Bio-aanvuiling is suksesvol waargeneem deur UTDR in buisvormige UF membrane. Ultrasoniese frekwensiespektra kan dus as ‘n bykomende metode gebruik word vir die waarneming van aanvuiling op skeidingsmembrane.

Not available / text

Thesis (MEng) -- Stellenbosch University, 2014. / ENGLISH ABSTRACT: When desalinating brackish water by reverse osmosis (RO) or other techniques, high overall water recoveries are essential to minimize brine production and the associated disposal costs thereof. As the overall water recovery increases, concentrations of sparingly soluble salts (e.g. barium sulphate, calcium sulphate) reach levels above saturation, especially near the membrane surface, drastically increasing the scaling propensity. Antiscalants are typically dosed into the feed water to prevent such scaling during RO desalination. However, the carry-over of antiscalant into the concentrate stream can complicate subsequent salt precipitation processes that may be used to increase overall water recovery. These precipitation techniques are sometimes used to reduce the levels of super-saturation in the RO concentrate prior to a subsequent RO desalination step. The purpose of this study was to assess the feasibility of reducing calcium sulphate scaling on RO membranes, by using periodic permeate flushing when feeding a lab-scale RO unit with a supersaturated calcium sulphate solution in the absence of anti-scalant. The overall water recovery was increased by recycling the concentrate, after an intermediate de-supersaturation step. This simulated a multiple-stage RO system, typical of processes used in high-recovery acid mine drainage (AMD) treatment plants. De-supersaturation of the concentrate intermediate was achieved with direct seeded gypsum precipitation, in the absence of any antiscalant. On the membrane surface inside the membrane unit, calcium sulphate concentrations greatly exceeded saturation levels – a combined consequence of the normal concentration process and the well-known surface-based concentration polarisation phenomenon. Therefore, periodic forward-flushing of the supersaturated solution from the membrane unit was performed with permeate. In theory, the periodic flushing removes the highly concentrated layer at the membrane surface during every flush, before scaling can occur. Various flushing regimes were evaluated to assess the effectiveness of the process. A lab-scale desalination unit with a 0.106 m2 flat sheet polyamide RO membrane was designed and constructed. The unit could operate at a feed rate of 12-14 L/h and at permeate fluxes of 12-24 LMH. Super-saturated feed solutions were prepared by mixing sodium sulphate and calcium chloride dihydrate salts with demineralised water, with an initial salinity of ± 5300 mg/L TDS, corresponding to a gypsum saturation index (SIg) of 1.2 for most experiments. The total production time, net permeate production and flux decline were used to compare the flushing efficiency in different experimental runs. Initial tests showed that scaling could be prevented (when operating the unit in full recycle mode, i.e. where both concentrate and permeate were recycled to feed), at flushing frequencies between 12 and 2.4 h-1, when the membrane feed and concentrate were slightly under-saturated (SIg = 0.9) and slightly super-saturated (SIg = 1.1) respectively. However, when switching the same system to non-flushing mode after 24 hours of operation, membrane scaling occurred within 2-3 hours, as indicated by a strong decline in flux. However, when operating the system in concentrate recycle mode (i.e. permeate is withdrawn) with super-saturated feed solutions (e.g. SIg = 1.2), and thus a notably more super-saturated solution in the membrane concentrate, scaling could not be prevented (albeit delayed for some time) with intermittent permeate flushing. A fractional 25-1 factorial design was used to determine which factors had the most significant effect on total production time and permeate production rate, testing five factors: 1) flushing frequency, 2) flushing volume, 3) permeate soak time, 4) permeate flux and 5) instantaneous recovery. The ANOVA analysis showed that total production times were, not surprisingly, primarily affected by the permeate flux, where operation at 24 LMH resulted in a lower net permeate production between 3.0 - 4.2 L, compared to 7.6 - 9.7 L at 12 LMH. Higher permeate fluxes clearly resulted in higher levels of concentration polarisation at the membrane surface, thus increasing the propensity for membrane scaling. Flushing frequency and instantaneous recovery also affected the net permeate production, where 6 h-1 and 10 % were the optimal values respectively within the range of test conditions. The lowest permeate production rate resulted in the highest net permeate volume production (i.e. also longest total production time), confirmed by a least squares regression. In summary: This study showed that periodic permeate flushing could delay the membrane scaling process. However, it failed to prevent membrane scaling completely when operating the system with supersaturated calcium sulphate solutions in the absence of antiscalants. The flushing technique effectively delayed the onset of precipitation, but scaling eventually occurred if the lab-scale RO system was operated in concentrate recycle mode with oversaturated feed solutions (SIg = 1.2). Additional experiments at different cross-flow velocities during permeate flushing, while using an optimised RO test cell flow channel design, are recommended for future studies. / AFRIKAANSE OPSOMMING: Gedurende die ontsouting van brakwater deur tegnieke soos tru-osmose (TO), is ʼn maksimum herwinning van water noodsaaklik om die produksie, en die gepaardgaande kostes van verwydering, van die sout/brak neweproduk te minimeer. Soos die herwinning van water verhoog, so ook verhoog die konsentrasie van moeilik-oplosbare soute (soos bariumsulfaat, kalsiumsulfaat) in die sout konsentraat stroom, totdat die soute uiteindelik superversadiging bereik. Hierdie superversadiging gebeur veral naby die membraanoppervlak, waar dit lei tot ʼn verhoogde kans van presipitasie en skaalvorming. Om dit te voorkom word die voerwater na ʼn TO stelsel tipies gedoseer met antiskaalmiddels. Hierdie antiskaalmiddels verlaat die stelsel saam met die konsentraat, waar hulle gevolglike die presipitasie van soute bemoeilik. Presipitasie van soute uit die konsentraat kan tipies gebruik word om die vlak van superversadiging in die konsentraat te verlaag, waarna verdere TO behandeling gebruik word om selfs ʼn hoër algehele waterherwinning te bewerkstellig. Die doel van hierdie studie was om die vatbaarheid van die vermindering van kalsiumsulfaat (gips) skaalvorming in die afwesigheid van antiskaalmiddels op TO membrane te toets. Dit is bewerkstellig deur ʼn laboratoriumskaal TO eenheid te voer met ʼn superversadigde kalsiumsulfaat oplossing en die membraan periodies met skoon produkwater (permeaat) te was. Die algehele waterherwinning is verhoog deur met ʼn tussenstap die versadigingsvlak van gips in die konsentraat te verlaag, waarna dit hersirkuleer is na die voertenk. Sodoende is ʼn multi-stadium TO stelsel nageboots, soos dit tipies in hoë herwinningsaanlegte, soos met die herwinning van suur mynwater (E: acid mine drainage, AMD), gebruik word. ʼn Verlaging in superversadiging van die konsentraat in die tussenstap is behaal deur die konsentraat direk aan gipskristalle bloot te stel om presipitasie te bewerkstellig in die afwesigheid van enige antiskaalmiddels. Gedurende eksperimente het die soutkonsentrasie op die membraanoppervlak in die TO eenheid superversadigingsvlakke vêr oorskry, as gevolg van die natuurlike konsentrasie proses en die bekende konsentrasie polarisasie oppervlaksverskynsel. Om hierdie superversadiging teen te werk is periodiese saamstroom spoeling van die membraan met skoon produkwater uitgevoer. In teorie het die periodiese spoeling die hoogs gekonsentreerde oplossing van die membraan oppervlak verwyder voor skaalvorming kan plaasvind. Verskillende spoelpatrone is ondersoek om die doeltreffendheid van die spoeling te bepaal. Om die eksperimente uit te voer is ʼn laboratoriumskaal ontsoutingsaanleg met ʼn maklik verwyderbare 0.106 m2 plat-vel poli-amied TO membraan ontwerp en gebou. Die aanleg kan vloeistof voertempo’s tussen 12-24 L/h hanteer en skoon produkwater teen 12-24 LHM lewer. Die superversadigde voer oplossings, soos gebruik in die meerderheid van die eksperimentes is voorberei deur natriumsulfaat en kalsiumchloried-dihidraat soute te meng in gedemineraliseerde water, tot ʼn soutgehalte van ± 5300 mg/L TDS bereik is. Hierdie soutgehalte stem ooreen met ʼn gips versadigingsindeks (E: gypsum saturation index, SIg) van 1.2. Die skoon produkwater totale produksietyd en netto produksie, asook die membraan vloed afname, is gebruik as veranderlikes om die spoel doeltreffendheid tussen eksperimentele lopies te vergelyk. Aanvanklike toetse het getoon dat skalering voorkom is by effens onderversadigde (SIg = 0.9) en effens superversadigde (SIg = 1.1) voer oplossings met die onderskeie spoel frekwensies van 12 en 2.4 h-1, (terwyl die aanleg in algehele hersirkulasie bedryf is, m.a.w. wanneer beide die konsentraat en produkwater gedurig na die voertenk hersirkuleer word). ʼn Effens-superversadigde eksperiment is ook sonder spoeling uitgevoer vir 24 uur. In hierdie geval het skaalvorming binne twee tot drie uur gebeur, soos bevestig deur ʼn skerp afname in die membraan vloed. Skaalvorming kon nie verhoed word terwyl die aanleg bedryf word met superversadigde (SIg = 1.2) voeroplossings en slegs konsentraat hersirkulasie nie (m.a.w. skoon produkwater word opgevang), alhoewel skaalvorming vertraag kon word. Hierdie operasie het tot beduidend meer gekonsentreerde oplossings in die membraan gelei. Om te bepaal watter faktore die grootste invloed op totale produksietyd en netto produksie van skoon produkwater het, is ʼn fraksionele faktoriaalontwerp van 25-1 uitgelê wat vyf faktore toets, naamlik: 1) spoel frekwensie, 2) spoel volume, 3) skoon produkwater weektyd, 4) membraanvloed en 5) oombliklike herwinning. ʼn AVOVA analise het getoon dat totale produksietyd hoofsaaklik deur membraanvloed beïnvloed is, soos verwag kan word. Dit word gestaaf deurdat die aanleg, bedryf teen 24 LMH, slegs 3 - 4.2 L netto produkwater gelewer het, teenoor 7.6 - 9.7 L by 12 LMH. Hoër membraan vloedtempo’s het tot hoër vlakke van konsentrasie polarisasie op die membraanoppervlak gelei, wat ʼn groter neiging tot skaalvorming tot gevolg gehad het. Spoelfrekwensie en oombliklike herwinning het ʼn invloed op die netto produksie van skoon produkwater gehad, met 6 h-1 en 10 % as die onderskeie optimale waardes. ʼn Kleinstekwadraat regressie het aangedui dat die laagste produksietempo van skoon produkwater die hoogste netto produksie van skoon produkwater gelewer het, (asook die langste produksietyd). In opsomming: Hierdie studie het getoon dat gereelde spoeling met skoon produkwater die membraan skaalproses kan vertraag. Gedurende bedryf met superversadigde kalsiumsulfaat oplossings sonder enige antiskaalmiddels is daar gevind dat skaalvorming nie geheel en al vermy kon word nie. Die spoeltegniek, soos gebruik in hierdie studie, het die aanvang van skaalvorming in die laboratorium skaal TO eenheid vertraag, maar bedryf met konsentraat hersirkulasie en superversadigde oplossings (SIg = 1.2) het steeds skaal gevorm. Bykomende eksperimente teen verskeie kruisvloei snelhede gedurende die spoel stap word aanbeveel vir toekomstige studies.

Securing water in the right quantities at the right quality for the right price is a major issue around the world. Membranes are making an increasingly important contribution to meeting this need; however their performance is limited by fouling. This thesis reports on an investigation into the fouling of systems related to water treatment using the Direct Observation Through the Membrane (DOTM). The investigation focused on the measurement of critical flux and observation of particle behaviour under a variety of conditions and for a number of different particles. The range of meanings attributed to critical flux in the literature was analysed and several proposals made for the improved use of the concept. In particular, critical flux determination techniques were classified by whether they measure resistance changes or particle deposition; leading to the definition of Critical Resistance and Critical Deposition Fluxes. In this thesis the deposition definition is used exclusively. The effect of Reynolds number and spacer orientation on critical flux was correlated for spacer-filled channels. The heterogeneous deposition patterns observed with regions of heavy deposition next to areas of little or no deposition. This pattern was related to the local hydrodynamics of spacer cells (a few mm2 in size). The correlations developed for critical flux in spacer-filled channels were adjusted for submicron particle size and incorporated into a SpiralWound Module (SWM) leaf model and then used to simulate the fouling of SWM leaves under a range of operating conditions and operating policies. The Mass Balance technique of critical flux determination was also briefly assessed. The applicability of critical flux criteria to SWM arrays was discussed. Fouling, particle behaviour and critical flux were also investigated in air-sparged systems. The post-cleaning water flux was found to be enhanced when the membrane is fouled in the presence of bubbles. The rate of flux decline was reduced by bubbles. Critical flux increased with air flowrate, and decreased with increased liquid flowrate and concentration. Bubbles caused particles to periodically deposit on the membrane. Particles were observed to stream past the membrane under the influence of back-diffusive forces. Video clips of particulate fouling are provided.