Thesis (MEng)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: This study is an introductory investigation into vaporizer technology as implemented in micro gas turbines. Experimental investigations are aimed at the development of expectations concerning the internal flow structure though vaporizers by generating application specific flow maps. Consolidation of these maps with other experimental data suggests that annular flow leads to increased evaporation rates. In addition, it was discovered that flow structure is affected by the injection angle and air and fuel flow rates. An investigation into the numerical modelling of vaporizers is based on two phase flow theory using a flow structure approach. The numerical behaviour is observed for parametric variations to establish the impact of assumptions. A final numerical model is formulated with empirically determined coefficients with fair correlation to experimental data. The results of this study yield recommendations towards the implementation and analysis of vaporizers with applied use in micro gas turbines. / AFRIKAANSE OPSOMMING: Hierdie studie is 'n inleidende ondersoek na verdamper tegnologie soos toegepas in mikro gasturbines. Eksperimentele ondersoeke is gerig op die ontwikkeling van kennis rakende die interne vloeistrukture deur verdampers met die bou van toepassingspesifieke vloeikaarte. Konsolidering van hierdie kaarte met verdere eksperimentele data dui daarop dat annulêre vloei lei tot verhoogde verdampingstempo’s. Daar is ook bevestig dat die vloei struktuur deur die inspuitingshoek en vloeitempo’s affekteer word. 'n Ondersoek na die numeriese modellering van verdampers is gebasseer op twee-fase vloei met 'n vloeistruktuur benadering. Die numeriese gedrag is waargeneem vir parametriese variasies om sodoende die impak van aannames te bevestig. Die numeriese model is voltooi met empiriese bepaalde koëffisiënte en lei tot goeie korrelasie met eksperimentele data. Resultate van hierdie studie lei tot aanbevelings rakende die implementering en ontleding van verdampers met spesifieke toepassing op mikro gas turbines.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: The use of micro gas turbines (MGTs) for the propulsion of unmanned aerial vehicles (UAVs) has become an industry standard. MGTs offer better performance vs. weight than similar sized, internal combustion engines. The front component of an MGT serves the purpose of compressing air, which is subsequently mixed with a fuel and ignited to both power the turbine which drives the compressor, and to produce thrust. Centrifugal compressors are typically used because of the high pressure ratios they deliver per stage. The purpose of this project was to design a centrifugal compressor impeller, and to devise a methodology and the tools with which to perform the aforementioned. A compressor impeller adhering to specific performance and dimensional requirements was designed. The new compressor was designed using a mean-line performance calculation code. The use of the code was vindicated through comparison with the results from a benchmark study. This comparison included mean-line, Computational Fluid Dynamic (CFD), and experimental results: the new design mean-line results were compared to the results of CFD simulations performed on the same design. The new design was optimised using an Artificial Neural Network (ANN) and Genetic Algorithm. Prior to and during optimisation, the ANN was trained using a database of sample CFD calculations. A Finite Element Analysis (FEA) was done on the optimised impeller geometry to ensure that failure would not occur during operation. According to CFD results, the final design delivered good performance at the design speed with regards to pressure ratio, efficiency, and stall margin. The mechanical stresses experienced during operation were also within limits. Experimental results showed good agreement with CFD results of the optimised impeller. Keywords: micro gas turbine, centrifugal compressor, impeller, CFD, experimental, optimisation, FEA. / AFRIKAANSE OPSOMMING: Die gebruik van mikrogasturbines vir die aandrywing van onbemande vliegtuie het ‟n standaard geword in die industrie. Mikrogasturbines bied beter werkverrigting teen gewig as binnebrandenjins van soortgelyke grote. Hierdie eienskap verseker dat mikrogasturbines as aandryfmotors vir onbemande vliegtuie uiters voordelig is. Die voorste komponent van ‟n mikrogasturbine dien om lug saam te pers, wat dan met brandstof gemeng en daarna aan die brand gesteek word om krag aan die kompressor en stukrag te voorsien. Sentrifugaalkompressors word tipies gebruik as gevolg van die hoë drukverhoudings wat hierdie komponente per stadium kan lewer. Die doel van hierdie projek was om ‟n sentrifugaalkompressor te ontwerp, en ‟n metode en die hulpmiddels te ontwikkel om laasgenoemde uit te voer. ‟n Kompressor rotor wat voldoen het aan sekere werkverrigtings en dimensionele vereistes is ontwerp. Die nuwe kompressor rotor is met behulp van 1-dimensionele werkverrigting-berekeningskode ontwerp. Die berekeningsakkuraatheid van die kode en díé van ‟n kommersiële Berekenings Vloeidinamika pakket is bevestig deur die berekende resultate te vergelyk met die van eksperimente. Die nuwe rotor is gevolglik deur middel van ‟n Kunsmatige Neurale Netwerk en Genetiese Algoritme geoptimeer. Die Kunsmatige Neurale Netwerk is voor en gedurende optimering deur Berekenings Vloeidinamika simulasies opgelei. Die meganiese sterkte van die geoptimeerde rotor is nagegaan met behulp van ‟n Eindige Element Analise. Dit is gedoen om te verseker dat die rotor nie sal faal by die bedryfspunt nie. Berekenings Vloeidinamika resultate het getoon dat die finale rotor ontwerp ‟n goeie werkverrigting lewer by die ontwerpspoed, met betrekking tot drukverhouding, bennutingsgraad, en stakingsmarge. Eksperimentele resultate het goeie ooreenstemming met die Berekenings Vloeidinamika resultate van die geoptimeerde rotor getoon. Sleutelwoorde: mikrogasturbine, sentrifigaalkompressor, rotor, Berekenings Vloeidinamika, eksperimenteel, optimering, Eindige Element Analise.

This paper presents an analysis of the potential of Micro Gas Turbines (MGT) with regards to performance, economic and durability considerations. The performance potential was assessed by calculating the cycle efficiency based on the Brayton cycle and the mechanical efficiency of the expansion turbine. The economic potential was evaluated by calculating the specific fuel consumption and estimating the cost and manufacturability of the turbine components. The durability and reliability of the components were assessed by considering the effects of transient thermal stresses and unstable ignition. The results indicated that ceramic materials can achieve a 63% increase in efficiency over nickel-based alloys and a 39% reduction in specific fuel consumption. It was also found that the grinding process on the metal-ceramic shaft connection is the most expensive as it relies on diamond grinding, while ceramic turbines can have an initial procurement cost advantage whenproduced in higher volumes. Finally, it was found that ceramic materials are less reliable due to their higher hardness and sensitivity to pressure spikes, and therefore require careful consideration when designing the components. / I detta dokument presenteras en analys av potentialen hos mikrogasturbiner (MGT) med avseende på prestanda, ekonomi och hållbarhet. Prestandapotentialen bedömdes genom att beräkna cykelns effektivitet baserad på Braytoncykeln och expansionsturbinens mekaniska effektivitet. Den ekonomiska potentialen utvärderades genom att beräkna den specifika bränsleförbrukningen och uppskatta kostnaden och tillverkningsbarheten för turbinkomponenterna. Komponenternas hållbarhet och tillförlitlighet bedömdes genom att man beaktade effekterna av tillfälliga termiska påfrestningar och instabil tändning. Resultaten visade att keramiska material kan öka effektiviteten med 63% jämfört med nickelbaserade legeringar och minskaden specifika bränsleförbrukningen med 39%. Det konstaterades också att slipningen av axelförbindelsen mellan metall och keramik är den dyraste eftersom den bygger på diamantslipning, medan keramiska turbiner kan ha en kostnadsfördel vid den första anskaffningen när de tillverkas i större volymer. Slutligen konstaterades det att keramiska material är mindre tillförlitliga på grund av deras högre hårdhet och känslighet för tryckspikar, och att det därför krävs noggranna överväganden vid utformningen av komponenterna.

Thesis (MScEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: The main components of a micro gas turbine engine are a centrifugal or mixed-flow compressor, a combustion chamber and a single stage axial-flow or radial-flow turbine. The goal of this thesis is to formulate a design methodology for small axial-flow turbines. This goal is pursued by developing five design-related capabilities and applying them to develop a turbine for an existing micro gas turbine engine. Firstly, a reverse engineering procedure for producing digital three-dimensional models of existing turbines is developed. Secondly, a procedure for generating candidate turbine designs from performance requirement information is presented. The third capability is to use independent analysis procedures to analyse the performance of a turbine design. The fourth capability is to perform structural analysis to investigate the behavior of a turbine design under static and dynamic loading. Lastly, a manufacturing process for prototypes of a feasible turbine design is developed. The reverse engineering procedure employs point cloud data from a coordinate measuring machine and a CT-scanner to generate a three-dimensional model of the turbine in an existing micro gas turbine engine. The design generation capability is used to design three new turbines to match the performance of the turbine in the existing micro gas turbine engine. Independent empirical and numerical turbine performance analysis procedures are developed. They are applied to the four turbine designs and, for the new turbine designs, the predicted efficiency values differ by less than 5% between the two procedures. A finite element analysis is used to show that the stresses in the roots of the turbine rotor blades are sufficiently low and that the dominant excitation frequencies do not approach any of the blade natural frequencies. Finally prototypes of the three new turbine designs are manufactured through an investment casting process. Patterns made of an organic wax-like material and a polystyrene material are used, with the former yielding superior results. / AFRIKAANSE OPSOMMING: Mikro-gasturbiene-enjins bestaan uit 'n sentrifugaal- of ‘n gemende-vloeikompressor, 'n verbrandingsruim en 'n enkel-stadium-aksiaalvloei- of ‘n radiaalvloei-turbine. Die doel van hierdie tesis is om 'n ontwerpsmetodologie vir klein aksiaalvloei-turbines saam te stel. Hierdie doel word deur die ontwikkeling en toepassing van vyf ontwerpsverwante vermoëns nagestreef. Eerstens word 'n tru-waartse-ingenieursproses ontwikkel om drie-dimensionele rekenaarmodelle van die bestaande turbines te skep. Tweedens word 'n metode om kandidaatturbineontwerpe vanaf werkverrigtingsvereistes te verkry, voorgestel. Die derde ontwerpsvermoë is om die werksverrigting van 'n turbineontwerp met onafhanklike analises te evalueer. Die vierde ontwerpsvermoë is om die struktuur van 'n turbinelem te analiseer sodat die effek van statiese en dinamiese belastings ondersoek kan word. Laastens word 'n vervaardigingsproses vir prototipes van geskikte turbineontwerpe ontwikkel. Die tru-waartse-ingenieursproses maak gebruik van 'n koördinaat-meet-masjien en 'n CT-skandeerder om puntewolkdata vanaf die turbine in 'n bestaande mikro-gasturbiene-enjin te verkry. Die data word dan gebruik om 'n drie-dimensionele model van die turbine te skep. Die ontwerpskeppingsvermoë word dan gebruik om drie kandidaatturbineontwerpe vir die bestaande mikro-gasturbiene-enjin te skep. Onafhanklike empiriese en numeriese prosedures om die werkverrigting van 'n turbineontwerp te analiseer word ontwikkel. Beide prosedures word op die vier turbineontwerpe toegepas. Daar word gevind dat die voorspelde benuttingsgraadwaardes van die nuwe ontwerpe met minder as 5% verskil vir die twee prosedures. 'n Eindige-element-analise word dan gebruik om te wys dat die spannings in die wortels van die turbinelemme laag genoeg is, asook dat die dominante opwekkingsfrekwensies nie die lem se natuurlike frekwensies nader nie. Laastens word prototipes van die drie nuwe turbineontwerpe deur 'n beleggingsgietproses vervaardig. In die vervaardigingproses word die effektiwiteit van twee materiale vir die gietpatrone getoets, naamlik 'n organiese wasagtige materiaal en 'n polistireen-materiaal. Daar word bevind dat die gebruik van die wasagtige gietpatrone tot beter resultate lei.

Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: This thesis details the methodology for developing a centrifugal compressor for application in a Micro Gas Turbine (MGT). This research forms part of a larger project, namely project Ballast, initiated by the South African Air Force (SAAF) in conjunction with Armscor. The methodology encompasses the development of a mean-line code that makes use of 1-dimensional theory in order to create an initial centrifugal compressor geometry which includes a rotor as well as radial vaned diffuser. This is followed by a Computational Fluid Dynamics (CFD) simulation process during which the compressor is optimised in order to maximise its performance. Before manufacturing a Finite Element Analysis (FEA) is done in order to ensure that the rotor does not fail during testing. The testing of the compressor is done to compare the numerical results with the experimental results and in so doing confirms the design process. A previous student had designed a rotor by making use of a mean-line code as well as a CFD optimisation process. The rotor had a measured total-static pressure ratio of roughly 2.8 at 121 kRPM and a total-total isentropic efficiency of 79.1 % at said rotational speed. The inclusion of a vaned diffuser resulted in a higher total-static pressure ratio and accordingly the compressor designed in this report has a CFD determined total-static pressure ratio of 3.0. The efficiency would however drop and as such a total-total isentropic efficiency of 76.5 % was determined theoretically. The theoretical results correlated well with the experimental results and as such it was concluded that the design methodology developed was sound. / AFRIKAANSE OPSOMMING: Hierdie tesis bespreek die metodologie vir die ontwikkeling van ‘n sentrifugale kompressor vir toepassing in ‘n Mikro-Gasturbine (MGT). Die tesis vorm deel van ‘n groter projek, genaamd die Ballast projek, wat deur die Suid-Afrikaanse Lugmag (SALM) daargestel is in samewerking met Krygkor. Die metodologie behels die ontwikkeling van ‘n middel-lyn kode wat gebruik maak van 1-dimensionele teorie om die aanvanklike geometrie van die kompressor te skep. Die geometrie bevat beide die rotor asook die gelemde radiale diffusor. Hierdie proses word gevolg deur ‘n Berekeningsvloeidinamika (BVD) simulasie waartydens die kompressor geoptimeer word om sodoende die verrigting ten volle te verbeter. Voordat vervaardiging plaasvind word ‘n Eindige Element Analise (EEA) toegepas om te verseker dat die rotor nie sal faal tydens toetse nie. Die toetse word gedoen sodat die eksperimentele resultate met die numeriese resultate vergelyk kan word. Sodoende word die proses waardeur die kompressor ontwikkel word bevestig. ‘n Vorige student het ‘n rotor ontwerp deur gebruik te maak van ‘n middel-lyn kode asook ‘n BVD optimerings proses. Die rotor het ‘n gemete totaal-statiese drukverhouding van ongeveer 2.8 teen 121 kRPM gelewer en ‘n totaal-totale isentropiese benutingsgraad van 79.1 % teen dieselfde omwentelingspoed. Met die insluiting van ‘n gelemde radiale diffuser word ‘n hoër totaal-statiese druk verhouding verwag en as sulks lewer die nuut-ontwerpte kompressor soos in die tesis bespreek ‘n teoretiese totaal-statiese drukverhouding van 3.0. Die benutingsgraad sal egter daal en daarvolgens het die nuwe kompressor ‘n totaal-totale isentropiese benutingsgraad van 76.5 % gelewer. Die eksperimentele resultate het goed ooreengestem met die teoretiese resultate en as sulks was dit besluit dat die ontwerps-metodologie goed is.