No description available.

Published Article / Selective laser micro-welding (SLMW) is a recent rapid manufacturing technique that produces metal parts through the use of a laser beam that selectively scans over the powder layers and fully melts and micro-welds the metallic particles. The advantage of SLMW is that any type of commercial steel alloys or other metal powders can be used to build parts in a single step without the need to add low melting point additives to join the particles as in the former SLS process. In this study, two types of low cost general purpose powders were evaluated as the raw materials for the selective laser micro-welding (SLMW): one powder is AISI304 stainless steel powder from Hoganas, Belgium (cost = $11/kg) and the other isAISI100510w carbon steel locally produced in-house from scrap steel using gas atomizing then de-oxidizing techniques (cost = $1.2/kg). Twelve sample parts were fabricated using two different laser speeds, 70 and 100 mm/s. Dimensions, density, hardness, tensile and microstructure properties were evaluated. Results showed that both powders successfully produced complete parts with accurate dimensions and fine details. Both microstructure phases were austenite due to the rapid heating and cooling cycles. At the higher speed of 100 mm/s mechanical properties deteriorated because of the porosities inside the structure. Using low cost powders gives more potential for the SLMW to spread as an economical manufacturing process in the near future.

Solar irradiation is a vast and plentiful source of energy. The use of photovoltaic (PV) devices to convert solar energy directly to electrical energy is an elegant way of sustainable power generation which can be distributed or in large PV plants based on the need. Solar cells are the small building blocks of photovoltaics and when connected together they form PV modules. Thin film solar cells require significantly less energy and raw materials to be produced, as compared to the dominant Si wafer technologies. CIGS thin film solar cells are considered to be the most promising thin film alternative due to its proven high efficiency. Most thin film PV modules utilise monolithic integration, whereby thin film patterning steps are included between film deposition steps, to create interconnection of individual cells within the layered structure. The state of the art is that CIGS thin film modules are made using one laser patterning step (P1) and two mechanical patterning steps (P2 and P3). Here we present work which successfully demonstrates the replacement of mechanical patterning by laser patterning methods. The use of laser ablation promises such advantages as increased active cell area and reduced maintenance and downtime required for regular replacement of mechanical tools. The laser tool can also be used to transform CIGS into a conducting compound along a patterned line. We have shown that this process can be performed after all semiconductor layers are deposited using a technique we call laser micro-welding. By performing patterning at the end of the process flow P2 and P3 patterning could be performed simultaneously. Such solutions will further reduce manufacturing times and may offer increased control of semiconductor interfaces. While showing promising performance on par with reference processes there are still open questions of importance for these novel techniques, particularly that of long term stability. Thin film modules are inherently sensitive to moisture and require reliable encapsulation. Before the techniques introduced here can be seen industrially they must have achieved proven stability. In this work we present a proof of existence of stable micro-welded interconnections. / Felaktigt tryckt som Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology 731

Das Ziel der vorliegenden Arbeit bestand in der Integration einer Technologie zur Erzeugung zeitlich alternierender (gepulster) Gasströme auf dem Gebiet der Laserfügetechnik. Für die technische Realisierung implizierte dies spezifische Anpassungen der drei Systemkernelemente (Stelleinheit, Messstrecke, Regelung) bzw. eine vollständige Neukonzeption des Technologieaufbaus. Die somit dem Anwender zur Verfügung stehenden neuen Parameter ermöglichten eine positive Beeinflussung des Fügeprozesses bzw. der Schweißergebnisse. Über die zeitliche Steuerung des Gasvolumenstroms in Korrespondenz zum Laserstrahlschweißprozess gelang es, mit Schutzgaspulsen eine Krafteinwirkung auf die Schmelze hervorzurufen und dadurch eine Verbesserung in Hinblick auf die Einschweißcharakteristik von lasergeschweißten Nähten zu realisieren. / The present study focuses on the integration of a technology for generating temporally alternating (pulsed) gas flows in the field of laser welding. The technical realization required the specific adaptation of the three core elements of the system (valve, section of measurements, control system) or rather a completely new concept of the technological setup. The new parameters allow for a positive influence on the joining process and on the results of welding, respectively. By means of temporal control of the gas volume flow in combination with a laser welding process, it was possible to produce a force effect on the molten.