No description available.

No description available.

The effects of using an insert Heat Flux Microsensor (HFM) versus an HFM deposited directly on a turbine blade to measure heat flux in a transonic cascade are investigated. The HFM is a thin-film sensor, 6.35 mm (0.250") in diameter (for an insert gage, including the housing) which measures heat flux and surface temperature. The thermal time response of both gages was modeled using a 1-D, finite difference technique and a 2-D, finite element solver. The transient response of the directly deposited gage was also tested against insert gages using an unsteady shock wave in a bench test setup and using a laser of known output. The effects of physical gage offset from the blade surface were also investigated. The physical offset of an insert HFM near the stagnation point on the suction side of a turbine blade was intentionally varied and the average heat transfer coefficient measured. Turbulence grids were used to study how offset affects the heat transfer coefficient with freestream turbulence added to the flow. The time constant of the directly deposited gage was measured to be 856 ms compared to less than 30 ms for the insert gages. Model results predict less than 20 ms for both gages and rule out the anodization layer (used for electrical isolation of the directly deposited gage from the blade) as the cause for the directly deposited gage's much slower time response. Offsets of ± 0.254 mm (0.010") at the gage location with an estimated boundary layer thickness of 0.10 mm (0.004") produced a higher average heat transfer coefficient than the 0.000" offset case. Using an insert HFM resulted in a higher average heat transfer coefficient than using the directly deposited gage and reduced the effects of freestream turbulence. To accurately measure heat transfer coefficients and the effects of freestream turbulence, the disruption of the flow caused by a gage must be minimized. Depositing a gage directly on the blade minimizes the effects of offset, but the cause of the slow time response must first be resolved if high speed data is to be taken. / Master of Science

In this paper, some critical issues and problems in the development of TiNi thin films were discussed, including preparation and characterization considerations, residual stress and adhesion, frequency improvement, fatigue and stability, as well as functionally graded or composite thin film design. Different types of MEMS applications were reviewed and the prospects for future advances in fabrication process and device development were discussed. / Singapore-MIT Alliance (SMA)

The dinoflagellate genus Symbiodinium is a popular research topic in the coral reef molecular biology field. Primarily because these organisms serve as the coral holobiont’s primary source of energy, carrying out photosynthesis, and providing hydrocarbons to the coral host. Previous studies have shown the difficulty of isolating Symbiodinium as well as the inherent problems in trying to quantify the diversity of this genus and to qualify the distinct reactions of different Symbiodinium sp. to changing environmental conditions. The main goals of this study are: (1) to detail the relationship between the genetic classification of the organism and its physiology in regard to photosynthesis with a number of established Symbiodinium cultures; and (2) to isolate Symbiodinium from coral of the central Red Sea. To evaluate the photosynthetic physiology of Symbiodinium, a microsensor was used to measure oxygen concentrations along with a phytoplankton analyzer system that used pulse-amplitude-modulation (Phyto-PAM) to measure fluorescence. In order to identify the particular clade that the isolates belonged to, denaturing gradient gel electrophoresis (PCR-DGGE) was used to identify Symbiodinium based on their internal transcribed spacer 2 (ITS2) region. These techniques helped us to achieve our goals in the following ways: Symbiodinium sp. from a culture collection were classified to the subclade level; species-specific and clade-specific photosynthetic profiles were generated; and a Symbiodinium sp. was isolated from the central Red Sea. This study provided preliminary correlation between the photosynthetic difference and Symbiodinium genetic classification; showed the probable existence of a self-protection system inside the Symbiodinium cells by comparing the difference between the initial oxygen production at the beginning of each light step and the oxygen production after light adaptation; and confirmed the possibility of the isolation of Symbiodinium.

No description available.

No description available.

No description available.

A presente pesquisa teve a intenção de desenvolver reator biológico de 159 \'M POT.3\' de volume total, com leito de carvões granulares (ativado e antracito) expandido e parcialmente aerado, para promover remoções de matéria orgânica e nutrientes (N e P) do esgoto sanitário, devido a manutenção de ambientes anaeróbio e aeróbio, estratificados ao longo da altura do reator e ao longo do biofilme cultivado em seu interior. Para avaliar o impacto das modificações operacionais no comportamento biológico dos microrganismos presentes no reator, foram aplicados métodos para análise das atividades nitrificante (ANE), desnitrificante (ADE) e metanogênica (PME), embasados em testes respirométricos padrões descritos na literatura. A estratificação reacional também foi estudada dentro de filmes biológicos com a ajuda de microsensores amperométricos de OD em testes de bancada. Assim, após 451 dias de operação, foi possível verificar remoções médias de \'DQO IND.F\', NTK e fosfato total de, respectivamente 78%, 56% e 42%, quando o reator foi operado por 66 dias com tempo de detenção hidráulica médio de 8,8 h, injetor de oxigênio puro, instalado após placa de orifício em linha de recirculação aerada, a qual funcionava pressurizada (3 a 4 bar) e com razão média de recirculação igual a 3, comparada à vazão de alimentação. Para o restante do período, no qual foram aplicadas taxas de carregamentos volumétricos médios de 0,74 \'+ OU -\' 0,28 kg\'DQO IND.F\'/\'M POT.3\'.dia; 0,17 \'+ OU -\' 0,07 kg NTK/\'M POT.3\'.dia e 0,05 \'+ OU -\' 0,02 kg\'PO IND.4\'POT.-3\'/\'M POT.3\'.dia, o sistema demonstrou remoções médias de 65 \'+ OU -\' 20% para \'DQO IND.F\', 25 \'+ OU -\' 21% para o NTK e 48 \'+ OU -\' 18% para o fosfato total, mesmo operado com tempo de retenção celular médio de 15 \'+ OU -\' 7 dias. Os testes respirométricos foram sensíveis para avaliar a atividade microbiana do material biológico coletado ao longo do reator, com os quais foram verificados PME médio de 0,25 mL\'CH IND.4\'/gSVT.h, para as amostras de material biológico coletado na região anaeróbia, ao fundo do reator; ANE variando entre 1,3 a 4,4 mg\'O IND.2\'/gSVT.h, para as amostras coletadas na região aeróbia, intermediária ao reator; e ADE variando entre 0,024 e 5,20 mg\'N IND.2\'/gSVT.h, para amostras coletadas, respectivamente, no fundo e no topo do reator. As análises do material líquido também corroboram com a idéia de estratificação dos ambientes aeróbio, no fundo do reator, e micro-aerado, em sua região intermediária superior, apontando para região com alto potencial de ocorrerem nitrificação e desnitrificação conjuntas no topo da sua zona reativa. O microsensor amperométrico de OD com ponta entre 10 e 30 \'mü\'m de diâmetro, confeccionados em laboratório especializado, se mostrou sensível para a observação do gradiente de concentração de oxigênio dissolvido dentro de filme biológico, suficientes para a formação de regiões aeróbia e anaeróbia em seu interior, cuja informação pode ser útil para a aprimoramento de reatores com biofilme, projetados para remoções combinadas de matéria orgânica e nutrientes. Entretanto, quando se pretende definir parâmetros cinéticos ou de transferência de massa, maior rigor deve ser dispensado na definição dos locais para a aplicação do sensor, nos quais sejam reduzidos os efeitos da heterogeneidade do agregado microbiano no ajuste da modelagem matemática aplicada aos pontos experimentais / The current research aimed the development of a 159 \'M POT.3\' total volume biological reactor, with a expanded and partially aerated granular coal bed (activated and anthracite), to promote organic matter and nutrients (N and P) removal from wastewater due to the maintenance of anaerobic and aerobic environments, stratified throughout the height of the reactor and also all over the biofilm cultivated in its interior. Methods for the analyses of specific nitrifying activities (ENA), denitrifying (EDA) and methanogenic (EMA) were applied to assess the impact of the operational modifications in the biological behavior of microorganisms present in the reactor, based on standard respirometric tests found in literature. The reactional stratification was also studied inside the biological films with the help of DO microsensors in batch tests. Thus, after 451 of operation it was possible to verify mean \'COD IND.F\', TNK and phosphate removal of 78%, 56% and 42%, respectively, when the reactor was operated for 66 days with average hydraulic detention time of 8.8 h, pure oxygen injector which was installed after the aerated recirculation line which was working pressurized (3 to 4 bar) and with mean recirculation ratio equal to 3, when compared to the feeding flow. For the rest of the period where mean volumetric loading rates of 0.74 \'+ OR -\' 0.28 kg\'COD IND.F\'/\'M POT.3\'.day; 0.17 \'+ OR -\' 0.07 kgTNK/\'M POT.3\'.day and 0.05 \'+ OR -\' 0.02 kg\'PO IND.4\'POT.-3\'/\'M POT.3\'.day were applied the system demonstrated average removal of 65 \'+ OR -\' 20% for \'COD IND.F\', 25 \'+ OR -\' 21% for TNK and 48 \'+ OR -\' 18% for total phosphate, even when it operated with mean cellular retention time of 15 \'+ OR -\' 7 days. The respirometric tests were sensible enough to assess the microbial activity from the biological material collected throughout the reactor, and where mean PME of 0.25 mL\'CH IND.4\'/gSVT.h was verified for the samples of biological material collected in the anaerobic region, at the bottom of the reactor; ANE varying between 1.3 to 4.4 mg\'O IND.2\'/gSVT.h, for the samples collected in the aerobic region, reactor\'s intermediary; and ADE varying between 0.024 to 5.20 mg\'N IND.2\'/gSVT.h, for samples collected at the bottom and the top of the reactor, respectively. The analyses of the liquid material also support the idea of stratification of the aerobic environments, at the bottom of the reactor, and micro-aerated, in its superior intermediate region, pointing to the region as a high potential of occurring joint nitrification and denitrification at the top of the reactive zone. The DO amperometric microsensor, with tip between 10 and 30 \'mü\'m of diameter, produced in a special laboratory, is sensible to the determination of dissolved oxygen concentration gradient inside biological film, sufficient for the formation of anaerobic and aerobic regions in its interior, this information can be useful to the improvement of biofilm reactors, projected for the combined removal of organic matter and nutrients. However, when the definition of kinetic parameters or mass transference is intended more strictness must be applied when choosing the locals for microsensor application, where the effects of the microbial aggregate heterogeneity is reduced in the adjustment of the mathematical modeling applied to the experimental points.

A presente pesquisa teve a intenção de desenvolver reator biológico de 159 \'M POT.3\' de volume total, com leito de carvões granulares (ativado e antracito) expandido e parcialmente aerado, para promover remoções de matéria orgânica e nutrientes (N e P) do esgoto sanitário, devido a manutenção de ambientes anaeróbio e aeróbio, estratificados ao longo da altura do reator e ao longo do biofilme cultivado em seu interior. Para avaliar o impacto das modificações operacionais no comportamento biológico dos microrganismos presentes no reator, foram aplicados métodos para análise das atividades nitrificante (ANE), desnitrificante (ADE) e metanogênica (PME), embasados em testes respirométricos padrões descritos na literatura. A estratificação reacional também foi estudada dentro de filmes biológicos com a ajuda de microsensores amperométricos de OD em testes de bancada. Assim, após 451 dias de operação, foi possível verificar remoções médias de \'DQO IND.F\', NTK e fosfato total de, respectivamente 78%, 56% e 42%, quando o reator foi operado por 66 dias com tempo de detenção hidráulica médio de 8,8 h, injetor de oxigênio puro, instalado após placa de orifício em linha de recirculação aerada, a qual funcionava pressurizada (3 a 4 bar) e com razão média de recirculação igual a 3, comparada à vazão de alimentação. Para o restante do período, no qual foram aplicadas taxas de carregamentos volumétricos médios de 0,74 \'+ OU -\' 0,28 kg\'DQO IND.F\'/\'M POT.3\'.dia; 0,17 \'+ OU -\' 0,07 kg NTK/\'M POT.3\'.dia e 0,05 \'+ OU -\' 0,02 kg\'PO IND.4\'POT.-3\'/\'M POT.3\'.dia, o sistema demonstrou remoções médias de 65 \'+ OU -\' 20% para \'DQO IND.F\', 25 \'+ OU -\' 21% para o NTK e 48 \'+ OU -\' 18% para o fosfato total, mesmo operado com tempo de retenção celular médio de 15 \'+ OU -\' 7 dias. Os testes respirométricos foram sensíveis para avaliar a atividade microbiana do material biológico coletado ao longo do reator, com os quais foram verificados PME médio de 0,25 mL\'CH IND.4\'/gSVT.h, para as amostras de material biológico coletado na região anaeróbia, ao fundo do reator; ANE variando entre 1,3 a 4,4 mg\'O IND.2\'/gSVT.h, para as amostras coletadas na região aeróbia, intermediária ao reator; e ADE variando entre 0,024 e 5,20 mg\'N IND.2\'/gSVT.h, para amostras coletadas, respectivamente, no fundo e no topo do reator. As análises do material líquido também corroboram com a idéia de estratificação dos ambientes aeróbio, no fundo do reator, e micro-aerado, em sua região intermediária superior, apontando para região com alto potencial de ocorrerem nitrificação e desnitrificação conjuntas no topo da sua zona reativa. O microsensor amperométrico de OD com ponta entre 10 e 30 \'mü\'m de diâmetro, confeccionados em laboratório especializado, se mostrou sensível para a observação do gradiente de concentração de oxigênio dissolvido dentro de filme biológico, suficientes para a formação de regiões aeróbia e anaeróbia em seu interior, cuja informação pode ser útil para a aprimoramento de reatores com biofilme, projetados para remoções combinadas de matéria orgânica e nutrientes. Entretanto, quando se pretende definir parâmetros cinéticos ou de transferência de massa, maior rigor deve ser dispensado na definição dos locais para a aplicação do sensor, nos quais sejam reduzidos os efeitos da heterogeneidade do agregado microbiano no ajuste da modelagem matemática aplicada aos pontos experimentais / The current research aimed the development of a 159 \'M POT.3\' total volume biological reactor, with a expanded and partially aerated granular coal bed (activated and anthracite), to promote organic matter and nutrients (N and P) removal from wastewater due to the maintenance of anaerobic and aerobic environments, stratified throughout the height of the reactor and also all over the biofilm cultivated in its interior. Methods for the analyses of specific nitrifying activities (ENA), denitrifying (EDA) and methanogenic (EMA) were applied to assess the impact of the operational modifications in the biological behavior of microorganisms present in the reactor, based on standard respirometric tests found in literature. The reactional stratification was also studied inside the biological films with the help of DO microsensors in batch tests. Thus, after 451 of operation it was possible to verify mean \'COD IND.F\', TNK and phosphate removal of 78%, 56% and 42%, respectively, when the reactor was operated for 66 days with average hydraulic detention time of 8.8 h, pure oxygen injector which was installed after the aerated recirculation line which was working pressurized (3 to 4 bar) and with mean recirculation ratio equal to 3, when compared to the feeding flow. For the rest of the period where mean volumetric loading rates of 0.74 \'+ OR -\' 0.28 kg\'COD IND.F\'/\'M POT.3\'.day; 0.17 \'+ OR -\' 0.07 kgTNK/\'M POT.3\'.day and 0.05 \'+ OR -\' 0.02 kg\'PO IND.4\'POT.-3\'/\'M POT.3\'.day were applied the system demonstrated average removal of 65 \'+ OR -\' 20% for \'COD IND.F\', 25 \'+ OR -\' 21% for TNK and 48 \'+ OR -\' 18% for total phosphate, even when it operated with mean cellular retention time of 15 \'+ OR -\' 7 days. The respirometric tests were sensible enough to assess the microbial activity from the biological material collected throughout the reactor, and where mean PME of 0.25 mL\'CH IND.4\'/gSVT.h was verified for the samples of biological material collected in the anaerobic region, at the bottom of the reactor; ANE varying between 1.3 to 4.4 mg\'O IND.2\'/gSVT.h, for the samples collected in the aerobic region, reactor\'s intermediary; and ADE varying between 0.024 to 5.20 mg\'N IND.2\'/gSVT.h, for samples collected at the bottom and the top of the reactor, respectively. The analyses of the liquid material also support the idea of stratification of the aerobic environments, at the bottom of the reactor, and micro-aerated, in its superior intermediate region, pointing to the region as a high potential of occurring joint nitrification and denitrification at the top of the reactive zone. The DO amperometric microsensor, with tip between 10 and 30 \'mü\'m of diameter, produced in a special laboratory, is sensible to the determination of dissolved oxygen concentration gradient inside biological film, sufficient for the formation of anaerobic and aerobic regions in its interior, this information can be useful to the improvement of biofilm reactors, projected for the combined removal of organic matter and nutrients. However, when the definition of kinetic parameters or mass transference is intended more strictness must be applied when choosing the locals for microsensor application, where the effects of the microbial aggregate heterogeneity is reduced in the adjustment of the mathematical modeling applied to the experimental points.