No description available.

In the first study, a new µ-HPLC column was developed using a monolithic silica gel as a column substrate for chiral separation by covalently modifying with (S, S)-Whelk-O1 chiral selector. The monolithic stationary phase was generated through a sol-gel process and prepared in situ in a 100 µm i.d. fused silica capillary tubing. The chromatographic performance was characterized in terms of retention factor, column efficiency, enantioselectivity and resolution, as well as the kinetics parameters affecting the separation. Comparison with a commercial particle packed HPLC column demonstrates a promising enantioselective resolving ability of the monolithic Whelk-O1 capillary column. The second project focuses on characterization of fluorescent sensor for zinc detection. In this work, we have examined the photophysical properties of the fluorescent probe sensor that has been developed in our laboratory for Zn2+ recognition via a photo-induced electron transfer (PET) sensing mechanism. To characterize the fundamental function of sensor, response curves have been conducted, using acetone/methanol (199:1), 1,4-dioxane, acetone, methanol and aqueous buffer as the solvent system. Similar to prior work from our group, the sensor was found to respond selectively to Zn2+ ions with fluorescence enhancement. The fluorescence properties and binding response were evaluated in the presence of water and a Lewis base, which we found to have a marked effect on the fluorescence signal. The selectivity of the sensor for Zn2+ was also observed and compared to other divalent metal such as Ca2+, Mg2+, Cu2+ and Hg2+ with the goal of learning fundamental information on the system that can aid in the development of future PET based sensors.

Submitted master thesis is by its character focused on development of polyaniline which would possess attributes typical for monolithic stationary phase. Developed polyaniline aims to be used in capillary liquid chromatography. Accompanying target of submitted master thesis is to provide solutions for variety of complications which follow the preparation of polyaniline in its desired form such as consistency in a form of solutions, gels and pastes, extremely fast polymerization reaction, limited solubility of cross-linking agents, solubility of monolithic polyaniline in polar mobile phases and insufficient bond of polyaniline to the inner wall of fused silica capillary tubing. Solutions for this complications are selection of ideal oxidation agent (ammonium persulfate), cross-linking agent (tris(4-aminophenyl)amine) and porogenic agent (methanol). Also, setting ideal ratio between oxidation agent, cross-linking agent and porogenic agent, heat treatment, choice of suitable mobile phase (tetrahydrofuran), adjustment of capillary wall using silanization agent (3-[3-(trimethoxysilyl)propyl]-aniline) and construction of equipment needed for quick filling of capillaries. Described development concluded in the preparation of solid polyaniline monolith which had a steady bond to the inner wall of fused...

Preterm birth (PTB) is defined as birth before the 37th week of pregnancy and affects 15 million infants per year. Presently, there is no clinical test to determine PTB risk. A 3D printed microfluidic device is being developed as a clinical test for PTB risk via detection of a panel of biomarkers. A significant step is extraction of the PTB biomarkers from blood serum. In this work, I developed 3D printed microfluidic devices in which monoliths can be polymerized. Using the monolith as a solid support to attach antibody, I show that ferritin, one of the PTB biomarkers, can be selectively extracted from human blood serum. This is the first study where a monolith has been formed in a 3D printed microfluidic device and used to perform an immunoaffinity extraction. This work is an important step in developing a clinical test for PTB risk. The realization of this work also demonstrates that 3D printing can be used to fabricate functional microfluidic devices.

Laboratory test results are important in making decisions regarding a patient's diagnosis and response to treatment. These tests often measure the biomarkers found in biological fluids such blood, urine, and saliva. Immunoassay is one type of laboratory test used to measure the level of biomarkers using specific antibodies. Microfluidics offer several advantages such as speed, small sample volume requirement, portability, integration, and automation. These advantages are motivating to develop microfluidic platforms of conventional laboratory tests. I have fabricated polymer microfluidic devices and developed immunoassays on-chip for potential cancer markers. Silicon template devices were fabricated using standard photolithographic techniques. The template design was transferred to a poly(methyl methacrylate) (PMMA) piece by hot embossing and subsequently bonded to another PMMA piece with holes for reservoirs. I used these devices to perform microchip immunoaffinity electrophoresis to detect purified recombinant thymidine kinase 1 (TK1). Buffer with 1% methylcellulose acted as a dynamic coating that minimized nonspecific adsorption of protein and as sieving matrix that enabled separation of free antibody from antibody-TK1 complexes. Using this technique, I was able to detect TK1 concentration >80 nM and obtained separation results within 1 minute using a 5 mm effective separation length. Detection of endogenous TK1 in serum is difficult because TK1 is present at the pM range. I compared three different depletion methods to eliminate high abundance immunoglobulin and human serum albumin. Cibacron blue columns depleted abundant protein but also nonspecifically bound TK1. I found that ammonium sulfate precipitation and IgG/albumin immunoaffinity columns effectively depleted high abundance proteins. TK1 was salted out of the serum with saturated ammonium sulfate and still maintained activity. To integrate affinity columns in microfluidic devices, I have developed a fast and easy strategy for initial optimization of monolith affinity columns using bulk polymerization of multiple monolith solutions. The morphology, surface area, and porosity, were qualitatively assessed using scanning electron microscopy. This method decreased the time, effort, and resources compared to in situ optimization of monoliths in microfluidic devices. This strategy could be used when designing novel formulations of monolith columns. I have also integrated poly(ethylene glycol dimethacrylate-glycidyl methacrylate) monolith affinity columns in polymer microfluidic devices to demonstrate the feasibility of extracting human interleukin 8 (IL8), a cancer biomarker, from saliva. Initial results have shown that the affinity column (~3 mm) was successfully integrated into the devices without prior surface modification. Furthermore, anti-IL8 was immobilized on the surface of the monolith. Electrochromatograms showed that 1 ng/mL of IL8 can be detected when in buffer while 10 ng/mL was detected when IL8 was spiked in saliva. Overall, these findings can be used to further develop immunoassays in microfluidic platforms, especially for analyzing biological fluids.

This dissertation focuses on the preparation of polymeric monolithic capillaries for ion exchange chromatography of peptides and proteins, since polymeric monoliths have shown promise for providing improved protein separations. Characteristics of monolithic columns include low back pressure, simplicity of fabrication and biocompatibility. Preparation of strong and weak cation-exchange monolithic stationary phases in 75 μm I.D. capillaries by direct in situ copolymerization was achieved using various functional monomers including sulfopropyl methacrylate, phosphoric acid 2-hydroxyethyl methacrylate, bis[2-(methacryloyloxy)ethyl] phosphate and 2-carboxyethyl acrylate with polyethylene glycol diacrylate and other PEG materials. The resulting monoliths provided excellent ion exchange capillary LC of peptides and proteins with good run-to-run [relative standard deviation (RSD) < 1.99%] and column-to-column (RSD < 5.64%) reproducibilities. Narrow peaks were obtained and peak capacities of over 20 were achieved. Dynamic binding capacities of over 30 mg/mL of column volume for lysozyme were measured. A single monomer was used to synthesize a phosphoric acid containing monolith to improve its stability and reproducibility. The monolith was synthesized from only BMEP in 75 μm I.D. UV transparent fused-silica capillaries by photo-initiated polymerization. A dynamic binding capacity (lysozyme) of approximately 70 mg/mL of column volume was measured. Efficiencies of 52,900 plates/m for peptides and 71,000 plates/m for proteins were obtained under isocratic conditions. Good reproducibilities were achieved. Zwitterionic monolithic columns based on photo-initiated copolymerization of N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl)ammonium betain and poly(ethylene glycol) diacrylate were prepared in 75 μm I.D. fused silica capillaries for hydrophilic interaction chromatography. Inverse size exclusion chromatography was used to characterize the pore structure of the resulting monolith. A typical hydrophilic interaction chromatography mechanism was observed when the organic content in the mobile phase was higher than 60%. Good separations of amides, phenols, and benzoic acids were achieved. The effects of mobile phase pH, salt concentration, and organic modifier content on retention were investigated.

Highly cross-linked monoliths prepared from single cross-linking monomers were found to increase surface area and stability. Therefore, seven cross-linking monomers, i.e., 1,3-butanediol dimethacrylate (1,3-BDDMA), 1,4-butanediol dimethacrylate (1,4-BDDMA), neopentyl glycol dimethacrylate (NPGDMA), 1,5-pentanediol dimethacrylate (1,5-PDDMA), 1,6-hexanediol dimethacrylate (1,6-HDDMA), 1,10-decanediol dimethacrylate (1,10-DDDMA), and 1,12-dodecanediol dimethacrylate (1,12-DoDDMA), were used to synthesize highly cross-linked monolithic columns in 75-µm i.d. capillaries by one-step UV-initiated polymerization using dodecanol and methanol as porogens for reversed-phase liquid chromatography (RPLC) of small molecules. Selection of porogen type and concentration was investigated in detail. Isocratic elution of alkylbenzenes at a flow rate of 300 nL/min was conducted for all of the monoliths. Gradient elution of alkylbenzenes and alkylparabens provided high resolution separations. Several of the monoliths demonstrated column efficiencies in excess of 50,000 plates/m. Monoliths with longer alkyl-bridging chains showed very little shrinking or swelling in solvents of different polarities. In addition, highly cross-linked monolithic capillary columns poly(1,6-HDDMA), poly(cyclohexanediol dimethacrylate) [poly(CHDDMA)] and poly(1,4-phenylene diacrylate) [poly(PHDA)], were synthesized and compared for RPLC of small molecules. Isocratic elution of alkylbenzenes was performed using 1,6-HDDMA and CHDDMA monolithic columns. Gradient elution of alkylbenzenes using all three monolithic columns showed good separations. Monolithic columns formed from 1,6-HDDMA, which had a linear alkyl-bridging chain structure, exhibited the highest column efficiencies (86,000 plates/m). Optimized columns showed high permeability and high run-to-run and column-to-column reproducibilities. Monoliths prepared from controlled/living polymerization was demonstrated exhibiting narrower molecular weight distribution and more homogeneous cross-linked structures due to the reversible character of this polymerization method. Thus, monolithic columns were developed from three cross-linking monomers, i.e., 1, 12-DoDDMA, trimethylolpropane trimethacrylate (TMPTMA) and pentaerythritol tetraacrylate (PETA) using organotellurium-mediated living radical polymerization (TERP) in 150-µm i.d. capillaries for RPLC of small molecules. Selection of the polymerization conditions for the 1,12-DoDDMA monolirh was investigated in detail. Isocratic elution of alkylbenzenes was achieved with good efficiency (47,700 to 64,200 plates/m for uracil) using all monolithic columns prepared using TERP.

Detection of disease specific biomarkers is of great importance in diagnosis and treatment of diseases. Modern bioanalytical techniques, such as liquid chromatography with mass spectrometry (LC-MS), have the ability to identify biomarkers, but their cost and scalability are two main drawbacks. Enzyme-linked immunosorbent assay (ELISA) is another potential tool, but it works best for proteins, rather than peptide biomarkers. Recently, microfluidics has emerged as a promising technique due to its small fluid volume consumption, rapidness, low fabrication cost, portability and versatility. Therefore, it shows prominent potential in the analysis of disease specific biomarkers. In this thesis, microfluidic systems that integrate monolith columns for preconcentration and on-chip labeling are developed to analyze several protein biomarkers. I have successfully fabricated cyclic olefin copolymer (COC) microfluidic devices with standard micromachining techniques. Monoliths are prepared in situ in microchannels via photopolymerization, and the physical properties of monoliths are optimized by varying the composition and concentration of monomers to achieve better flow and extraction. On-chip labeling of protein biomarkers is achieved by driving solution through the monolith using voltage and incubating fluorescent dye with protein retained in the monolith. Subsequently, the labeled proteins are eluted by applying voltages to reservoirs on the microdevice and detected by laser-induced fluorescence. Finally, automation of on-chip preconcentration and labeling is successfully demonstrated.

The work deals with the static solution of monolithic reinforced concrete multi-purpose building, which includes a design point - supported panel, columns, flaps, underground wall and base band. Assessment of these structures in terms od first critical state -carrying capacity.

Polymers which are sensitive towards external physical, chemical and electrical stimuli are termed as ‘intelligent materials’ and are widely used in medical and engineering applications. Presently, polymers which can undergo a physical change when heat is applied at a certain temperature (cloud point) in water are well-studied for this property in areas of separation chemistry, gene and drug delivery and as surface modifiers. One example of such a polymer is the poly (N-isopropylacrylamide) PNIPAAM, where it is dissolved well in water below 32 oC, while by increasing the temperature further leads to its precipitation. In this work, an alternative polymer poly (2-(2-methoxy ethoxy)ethyl methacrylate-co- oligo(ethylene glycol) methacrylate) (P(MEO2MA-co-OEGMA)) is studied due to its biocompatibility and the ability to vary its cloud points in water. When a layer of temperature responsive polymer was attached to a single continuous porous piece of silica-based material known as a monolith, the thermoresponsive characteristic was transferred to the column surfaces. The hybrid material was demonstrated to act as a simple temperature ‘switch’ in the separation of a mixture of five steroids under water. Different analytes were observed to be separated under varying column temperatures. Furthermore, more complex biochemical compounds such as proteins were also tested for separation. The importance of this work is attributed to separation processes utilizing environmentally friendly conditions, since harsh chemical environments conventionally used to resolve biocompounds could cause their biological activities to be rendered inactive. / Polymere, welche empfindlich gegenüber externen physikalischen, chemischen und elektrischen Einflüssen sind, werden „intelligente Materialien“ genannt. Diese werden weitverbreitet in medizinischen und technischen Anwendungen eingesetzt. Auf diesem Gebiet ausführlich erforschte Materialien sind Polymere, welche durch Hitze bei einer bestimmten Temperatur (Trübungspunkt) eine physikalische Veränderung eingehen können, genannt thermoresponsive Polymere. Eingesetzt werden diese z.B. in chromatographischen Trennverfahren, in Gen- und Wirkstofftransport Vorgängen und zur Oberflächenmodifikation. Ein Beispiel für so ein Polymer ist das poly(N-isopropylacrylamide) PNIPAAM, welches unter 32 °C in Wasser gelöst vorliegt und mit Erhöhung der Temperatur als Niederschlag ausfällt. In dieser Arbeit wurde ein alternatives Polymer, das poly(2-(2-methoxyethoxy)ethylmethacrylate-co-oligo(ethyleneglycol) methacrylate) (P(MEO2MA-co-OEGMA)), untersucht, in Bezug auf Biokompatibilität und der Änderung des Trübungspunktes in Wasser. Wenn eine Schicht eines temperaturempfindlichen Polymers auf einen Monolithen (einteiliger, poröser und auf Silika-basierendes Material) aufgebracht wird, werden die thermoresponsiven Eigenschaften auf die Oberfläche dieses Monolithen übertragen. Der Monolith dient hier als Säule in einer HPLC-Anlage. Es wurde gezeigt, dass das Hybrid-Material als einfacher „Temperaturschalter“ in der Trennung von fünf verschiedenen Steroiden in Wasser agieren kann. Untersucht wurde die Separation verschiedener Analyten mit dem Variieren der Säulentemperatur. Zusätzlich wurden mehr komplexe biochemische Stoffe, wie Proteine, getestet. Die Bedeutung dieser Arbeit ist zurückzuführen auf Separationsprozesse, welche umweltfreundlichen Bedingungen nutzen, da die rauen chemischen Bedingungen in konventionellen Separationsprozessen die biologische Inaktivität der Verbindungen zur Folge haben können. Der zweite Teil der Arbeit beschäftigte sich mit der Entwicklung eines alternativen Trägermaterials als Ersatz zu den Silika-basierende Trennungssäulen. Kohlenstoffmaterialien sind aufgrund ihrer ausgezeichneten mechanischen Härte und chemischen Stabilität eine vielversprechend Alternative. Die Synthese von Kohlenstoffkugeln als Trägermaterial kann als „grüner“ Prozess in meiner Arbeit angesehen werden, da milde Synthesebedingungen in purem Wasser verwendet wurden. Die Leistungsfähigkeit des Materials wurde mit einer Serie von Separationsreaktionen gezeigt.