The research summarized by this thesis was comprised of an experimental analysis of beams loaded perpendicular to grain at midspan by a bolted double-shear laterally-loaded connection. Connection specimens were loaded monotonically until capacity was reached. Variables of consideration included the loaded edge distance of the connection main member, the span:depth ratio of the main member, and the main member material. Southern pine machine-stress-rated (MSR) lumber, laminated veneer lumber (LVL), and parallel strand lumber (PSL) were the three material types included in the program. Experimental results were compared with theoretical predictions from three models: the yield theory-based general dowel equations, which are currently the standard for laterally-loaded connection design in the U.S., and two models based upon fracture mechanics. All material property inputs required by the three models, were measured in the experimental program of this research and used to produce theoretical predictions. Comparisons were also made with respect to design values in the form of calculated factors of safety, over-strengths, and design factors of safety. Test results and observed trends are provided for all connection and material property tests. Notable trends included failure by splitting for all connections at low loaded edge distances, and variable span:depth ratios generally having a negligible effect on both connection and model performance. In most cases, the general dowel equations were more accurate than the two fracture models, however it should be noted that all three models over-predicted connection capacity at low loaded edge distances. / Master of Science

The emphasis of this dissertation is on using numerical and plasticity based methods to study two main areas of offshore geotechnics. The first part of this dissertation focuses on the undrained behavior of deeply embedded anchor plates under combined shear and torsion. Plate anchors are increasingly being used instead of typical foundation systems to anchor offshore floating platforms to sustain uplift operating forces. However extreme loading cases would create general loading conditions involving six degrees of freedom. The focus of my research was to evaluate the bearing capacity of plate anchors under two-way horizontal and torsional loading and to study the decreasing effect of torsional moment on the horizontal bearing capacity of these foundations. The study takes advantage of several approaches: Numerical simulation (two and three dimensional finite element analysis) Evaluating and modification of the available plasticity solutions Developing equations for three degree-of-freedom yield locus surfaces The same methodology is applied to evaluate the response of shallow foundations for subsea infrastructure subjected to significant eccentric horizontal loads. The second part of this study focuses on offshore geohazards. Coastal communities and the offshore industry can be impacted directly by geohazards, such as submarine slope failures, or by tsunamis generated by the failed mass movements. This study aims at evaluating the triggering mechanisms of submarine landslide under cyclic wave and earthquake loading. A simple effective stress elasto-plastic model with a minimal number of parameters accounting for monotonic and cyclic response of fine-grained material is developed. The new constitutive soil model could be used to simulate case histories and conduct parametric study to evaluate the effect of slope inclination angle, the earthquake loading with different PGA, frequency content, and duration, as well as various deposition rates to simulate different over pressure levels. This study will generate more insight on the static and cyclic behavior of submarine slopes and influencing factors on their triggering mechanisms using more comprehensive and realistic modeling tools. Several objectives are defined: Developing an appropriate constitutive formulation, Evaluating the constitutive model and material parameters for available databases.

Au cours des 50 dernières années, l’étude du phénomène de liquéfaction de sols sableux saturés ont fait l'objet de nombreuses recherches en laboratoire. La plupart de ces recherches antérieures se sont concentrées sur la liquéfaction de sables propres, en supposant que la présence de fines limite le développement de la surpression interstitielle et donc le risque de liquéfaction. Cependant, les sables sableux naturels se trouvent généralement dans la nature sous la forme d'un mélange de sable et de fines et, l’influence de ces fines sur le risque de liquéfaction de ce type de matériau n'est toujours pas claire. En effet, on trouve des résultats contradictoires, dans la littérature, sur l'effet des particules fines sur le phénomène de liquéfaction des sables. Dans ce contexte, l’objectif principal de ce travail expérimental est de clarifier et de quantifier l’influence des particules fines présentes au sein d’une matrice sableuse sur l’initiation et le développement du phénomène de liquéfaction. On s’est intéressé, en particulier, à la nature des particules fines (plastique/non-plastique), à leur proportion au sein de la matrice, à l’état de compacité de la matrice et à l’état de contrainte initial (état de consolidation). A cet effet, à l'aide d'un nouveau dispositif triaxial servo-hydraulique, une série d'essais monotones et cycliques ont été effectués afin de clarifier cet effet. Les résultats expérimentaux montrent que l'augmentation de la proportion de fines non plastiques augmente la résistance à la liquéfaction du mélange sous chargements monotone et cyclique. Par contre, cette tendance est inversée pour les mélanges qui contiennent des fines plastiques. Enfin, une comparaison a été établie entre le comportement de ces sols sous cisaillement monotone et cyclique non drainé en termes d'évaluation du déclenchement du phénomène d'instabilité et d'autres paramètres mécaniques / Since the last 50 years, the study of the phenomenon of liquefaction of saturated sandy soils has been a topic of extensive laboratory research. Most of the earlier research has focused on the liquefaction of clean sands assuming that the presence of fines resists the development of pore water pressure as well as the risk of liquefaction. However, natural sand is found in nature under the form of a mixture of sand and fines and, the influence of these fines on the liquefaction risk of this type of material is still unclear. In fact, we could find contradictory results in the literature review of the effect of fine particles on the sand liquefaction phenomenon. In this context, the main objective of this study is to clarify and quantify the influence of fine particles (plastic and non-plastic) present in a sandy matrix on the initiation and development of the liquefaction phenomenon .We’ve focused, in particular, on the nature of fine particles (plastic/non-plastic), their proportion in the matrix, the matrix compactness condition and initial stress state (state consolidation). For this purpose, with the aid of a new triaxial servo-hydraulic device, a series of monotonic and cyclic tests were done in order to clarify this effect. Experimental results show that the increase in non-plastic fines increases the resistance to liquefaction of the mixture under both monotonic and cyclic loading. However, this trend is reversed for the mixtures containing plastic fines. Finally a comparison has been established between the behavior of these soils under undrained monotonic and cyclic shearing in terms of evaluation of the initiation of instability phenomenon and other mechanical parameters

Este trabalho descreve o comportamento da aderência do concreto armado sob ações monotônicas e repetidas através de uma revisão bibliográfica e de ensaios de arrancamento padronizados. A influência de alguns parâmetros foi analisada, como diâmetro da armadura, tipo e amplitude de carregamento. Os resultados dos ensaios monotônicos foram comparados com as recomendações do CEB-FIP MC 1990, EUROCODE 2 e NB-1/78. Também foi realizada a análise numérica da aderência monotônica por meio de elementos finitos. Considerou-se a barra lisa, elementos de contato entre o aço e concreto e comportamento elástico-linear dos materiais; pois a ruína experimental da ligação ocorreu pelo corte do concreto entre as nervuras. A resistência monotônica da ligação ficou compreendida entre condições boas e ruins de aderência. Os resultados calculados de acordo com as normas foram muito diferentes em relação aos valores experimentais, e apresentaram uma dispersão muito grande. A força repetida ocasionou a perda de aderência pelo crescimento progressivo dos deslizamentos. Os modelos numéricos não representaram o comportamento experimental, devido à resposta força-deslizamento não-linear. / This research describes the bond behaviour in reinforced concrete under monotonic and repeated loading through a state-of-art and standard pull-out tests. The influence of some parameters was analysed as deformed bar diameter, type and amplitude of loading. The monotonic test results were compared with recommendations of CEB-FIP MC 1990, EUROCODE 2 and NB-1/78. The numerical analysis of monotonic bond was realized through finite elements. It was considered smooth bar, contact elements between the steel and concrete, and materials as of linear-elastic behaviour, because the experimental degradation of bond was caused by concrete between the ribs sheared off. The monotonic bond resistance resulted between good and bad bond conditions. The results calculated according to the codes were very different from the experimental values and very disperse. The repeated loading causes bond degradation by progressive increase of slip. The numerical specimens did not represent the experimental behaviour because of the non-linear load-slip response.

Trabecular bone is a porous composite material which consists of a mineral phase (mainly hydroxyapatite), organic phase (mostly type I collagen) and water assembled into a complex, hierarchical structure. In biomechanical modelling, its mechanical response to loads is generally assumed to be instantaneous, i.e. it is treated as a time-independent material. It is, however, recognised that the response of trabecular bone to loads is time-dependent. Study of this time-dependent behaviour is important in several contexts such as: to understand energy dissipation ability of bone; to understand the age-related non-traumatic fractures; to predict implant loosening due to cyclic loading; to understand progressive vertebral deformity; and for pre-clinical evaluation of total joint replacement. To investigate time-dependent behaviour, bovine trabecular bone samples were subjected to compressive loading, creep, unloading and recovery at multiple load levels (corresponding to apparent strain of 2,000-25,000 με). The results show that: the time-dependent behaviour of trabecular bone comprises of both recoverable and irrecoverable strains; the strain response is nonlinearly related to applied load levels; and the response is associated with bone volume fraction. It was found that bone with low porosity demonstrates elastic stiffening followed by elastic softening, while elastic softening is demonstrated by porous bone at relatively low loads. Linear, nonlinear viscoelastic and nonlinear viscoelastic-viscoplastic constitutive models were developed to predict trabecular bone's time-dependent behaviour. Nonlinear viscoelastic constitutive model was found to predict the recovery behaviour well, while nonlinear viscoelastic-viscoplastic model predicts the full creep-recovery behaviour reasonably well. Depending on the requirements all these models can be used to incorporate time-dependent behaviour in finite element models. To evaluate the contribution of the key constituents of trabecular bone and its microstructure, tests were conducted on demineralised and deproteinised samples. Reversed cyclic loading experiments (tension to compression) were conducted on demineralised trabecular bone samples. It was found that demineralised bone exhibits asymmetric mechanical response - elastic stiffening in tension and softening in compression. This tension to compression transition was found to be smooth. Tensile multiple-load-creep-unload-recovery experiments on demineralised trabecular samples show irrecoverable strain (or residual strain) even at the low stress levels. Demineralised trabecular bone samples demonstrate elastic stiffening with increasing load levels in tension, and their time-dependent behaviour is nonlinear with respect to applied loads . Nonlinear viscoelastic constitutive model was developed which can predict its recovery behaviour well. Experiments on deproteinised samples showed that their modulus and strength are reasonably well related to bone volume fraction. The study considers an application of time-dependent behaviour of trabecular bone. Time-dependent properties are assigned to trabecular bone in a bone-screw system, in which the screw is subjected to cyclic loading. It is found that separation between bone and the screw at the interface can increase with increasing number of cycles which can accentuate loosening. The relative larger deformation occurs when this system to be loaded at the higher loading frequency. The deformation at the bone-screw interface is related to trabecular bone's bone volume fraction; screws in a more porous bone are at a higher risk of loosening.

Este trabalho descreve o comportamento da aderência do concreto armado sob ações monotônicas e repetidas através de uma revisão bibliográfica e de ensaios de arrancamento padronizados. A influência de alguns parâmetros foi analisada, como diâmetro da armadura, tipo e amplitude de carregamento. Os resultados dos ensaios monotônicos foram comparados com as recomendações do CEB-FIP MC 1990, EUROCODE 2 e NB-1/78. Também foi realizada a análise numérica da aderência monotônica por meio de elementos finitos. Considerou-se a barra lisa, elementos de contato entre o aço e concreto e comportamento elástico-linear dos materiais; pois a ruína experimental da ligação ocorreu pelo corte do concreto entre as nervuras. A resistência monotônica da ligação ficou compreendida entre condições boas e ruins de aderência. Os resultados calculados de acordo com as normas foram muito diferentes em relação aos valores experimentais, e apresentaram uma dispersão muito grande. A força repetida ocasionou a perda de aderência pelo crescimento progressivo dos deslizamentos. Os modelos numéricos não representaram o comportamento experimental, devido à resposta força-deslizamento não-linear. / This research describes the bond behaviour in reinforced concrete under monotonic and repeated loading through a state-of-art and standard pull-out tests. The influence of some parameters was analysed as deformed bar diameter, type and amplitude of loading. The monotonic test results were compared with recommendations of CEB-FIP MC 1990, EUROCODE 2 and NB-1/78. The numerical analysis of monotonic bond was realized through finite elements. It was considered smooth bar, contact elements between the steel and concrete, and materials as of linear-elastic behaviour, because the experimental degradation of bond was caused by concrete between the ribs sheared off. The monotonic bond resistance resulted between good and bad bond conditions. The results calculated according to the codes were very different from the experimental values and very disperse. The repeated loading causes bond degradation by progressive increase of slip. The numerical specimens did not represent the experimental behaviour because of the non-linear load-slip response.

Résumé: L’objectif de cette thèse est d’interpréter la dégradation des aspérités des joints rocheux sous différentes conditions de chargement. Pour cela, la variation des aspérités durant les différentes étapes du cisaillement d’un joint rocheux est observée. Selon le concept appelé “tiny windows”, une nouvelle méthodologie de caractérisation des épontes des joints a été développée. La méthodologie est basée sur les coordonnées tridimensionnelles de la surface des joints et elles sont mesurées après chaque essai. Après la reconstruction du modèle géométrique de la surface du joint, les zones en contact sont identifiées à travers la comparaison des hauteurs des “tiny windows” superposées. Ainsi, la distribution des zones de la surface en contact, endommagées et sans contact ont été identifiées. La méthode d’analyse d’image a été utilisée pour vérifier les résultats de la méthodologie proposée. Les résultats indiquent que cette méthode est appropriée pour déterminer la taille et la distribution des surfaces du joint en contact et endommagées à différentes étapes du cisaillement. Un ensemble de 38 répliques ont été préparées en coulant du mortier sans retrait sur une surface de fracture obtenue à partir d’un bloc de granite. Différentes conditions de chargement, incluant des chargements statiques et cycliques ont été appliquées afin d’étudier la dégradation des aspérités à différentes étapes du procédé de cisaillement. Les propriétés géométriques des “tiny windows” en contact en phase pré-pic, pic, post-pic et résiduelle ont été analysées en fonction de leurs angles et de leurs auteurs. Il a été remarqué que les facettes des aspérités faisant face à la direction de cisaillement jouent un rôle majeur dans le cisaillement. Aussi, il a été observé que les aspérités présentent différentes contributions dans le cisaillement. Les aspérités les plus aigües (“tiny windows” les plus inclinées) sont abîmées et les aspérités les plus plates glissent les unes sur les autres. Les aspérités d’angles intermédiaires sont définies comme “angle seuil endommagé” et “angle seuil en contact”. En augmentant la charge normale, les angles seuils diminuent d’une part et, d’autre part, le nombre de zones endommagées et en contact augmentent. Pour un petit nombre de cycles (avec faible amplitude et fréquence), indépendamment de l’amplitude, une contraction apparaît ; par conséquent, la surface en contact et les paramètres de résistance au cisaillement augmentent légèrement. Pour un grand nombre de cycles, la dégradation est observée à l’échelle des aspérités de second ordre, d’où une baisse des paramètres de résistance au cisaillement. Il a été aussi observée que les “tiny windows” avec différentes inclinaisons contribuent au processus de cisaillement, en plus des “tiny windows” les plus inclinées (aspérités plus aigües). Les résultats de la méthode proposée montrent que la différenciation entre les zones en contact et celles endommagées s’avère utile pour une meilleure compréhension du mécanisme de cisaillement des joints rocheux. / Abstract: The objective of the current research is to interpret the asperity degradation of rock joints under different loading conditions. For this aim, the changes of asperities during different stages of shearing in the three-dimensional joint surface are tracked. According to a concept named ‘tiny window’, a new methodology for the characterization of the joint surfaces was developed. The methodology is based on the three-dimensional coordinates of the joints surface that are captured before and after each test. After the reconstruction of geometric models of joint surface, in-contact areas were identified according to the height comparison of the face to face tiny windows. Therefore, the distribution and size of just in-contact areas, in-contact damaged areas and not in-contact areas are identified. Image analysis method was used to verify the results of the proposed method. The results indicated that the proposed method is suitable for determining the size and distribution of the contact and damaged areas at any shearing stage. A total of 38 replicas were prepared by pouring non-shrinking cement mortar on a fresh joint surface of a split granite block. Various loading conditions include monotonic and cyclic loading were applied to study the asperities degradation at different stages of shearing. The geometric properties of the in-contact tiny windows in the pre-peak, peak, post-peak softening and residual shearing stages were investigated based on their angle and height. It was found that those asperities facing the shear direction have the primary role in shearing. It is remarkable that different part of these asperities has their own special cooperation in shearing. The steepest parts (steeper tiny windows) are wore and the flatter parts (flatter tiny windows) are slid. The borderlines between these tiny windows defined as “damaged threshold angle” and “in-contact threshold angle”. By increasing normal load, both the amounts of threshold angles are decreased and contact and damaged areas increased. During low numbers of cycles (with low amplitude and frequency), independent of the type of cycle, contraction occurs and consequently the contact area and the shear strength parameters slightly increased. During larger number of cycles, degradation occurred on the second order asperities, therefore the shear strength parameters slowly decreased. It was also observed that tiny windows with different heights participate in the shearing process, not just the highest ones. The results of the proposed method indicated that considering differences between just in-contact areas and damaged areas provide useful insights into understanding the shear mechanism of rock joints.

No description available.